Euro-Pro UV209H owner manual Operating Instructions

Page 6
Fig. 3
Fig. 2
Fig. 1

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Assembling Your Vacuum Cleaner

Note: Do not plug the power cord into an electrical outlet until the vacuum is fully assembled.

Handle Assembly

1.Carefully unpack all components, set aside packaging.

2.Lift vacuum body to upright position.

3.Remove the screw (1) that comes attached to the

body.

4.From the rear of the vacuum, align the handle with groove and slide onto vacuum. If necessary, use

thumb and finger pressure to slide handle into position.

5.Once handle is in place, secure the handle with the screws (2). (Fig. 1)

Caution: Do not over tighten. Over tightening could strip the screw holes. Do not operate the vacuum without the handle screws in place.

Cord Assembly

1.Make sure that the quick release cord holder is in the upright position.

2.Remove the wire tie from the power cord.

3.Wrap the cord into place by wrapping it in a clockwise direction around the quick release cord holder and the lower cord holders. (Fig. 2)

4. Turn the quick release cord holder

to the left or to the right to unwrap the power cord. (Fig. 2)

Warning: Always make sure that the vacuum is turned off before unplugging.

Using the Attachments

1.Place vacuum in its upright position. Make sure that the vacuum cleaner is NOT plugged into the electrical outlet when adding or removing accessories.

2.Turn the carpet height selector

to the highest position and set the Carpet to Floor selector to the “Floor” position.

3.Remove the hose connector from the rear of the unit and push in the desired attachment firmly onto the end of the hose.

4.If additional length is required, attach the extension tubes to the end of the hose and then attach the crevice tool, round brush or upholstery brush to the end of the extension tube.

Warning: Avoid tipping the vacuum or setting it on furniture, fringed area rugs or carpeted stairs while you are using the hose with the attachments. When using the unit to vacuum floors or with attachments, set the Carpet to Floor Selector to the “Floor” position. This will stop the beater brush from rotating. When vacuuming carpets, avoid leaving the vacuum in one place for an extended period of time, particularly on thick carpet.

Caution: Do NOT pull the vacuum cleaner around the room by the hose as it could tip over and cause damage. When using the attachments, do NOT over extend the hose length when reaching. Trying to reach beyond the hose reach could cause the vacuum to tip over.

How to Start

The upright vacuum can be used on multiple types of carpeting, bare floors or upholstery with attachments. When using the attachment tools such as the crevice tool, round brush or the upholstery brush, place the handle of the vacuum in the upright position.

1.Turn the quick release cord holder to either side 180° to release the power cord.

2.Plug the power cord into the electrical outlet.

3.Push the On/Off button to the "On" position to turn the vacuum on.

4. To release the handle, step on the power

head and pull the handle back.

Cleaning & Changing the Belt

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, HEPA filter,changing the filters or performing maintenance/trouble shooting checks.

Occasionally the power nozzle drive belt will require changing, the frequency will depend upon the amount of use your vacuum sees.

1.Turn the vacuum "Off" and unplug from power supply.

2.Turn the vacuum upside down on a flat level surface.

3.With a coin or a thick flat head screwdriver, unlock the two (2) screw locks by turning counter- clockwise. (Fig. 22)

Fig. 22

4.Remove the bottom cover of the power head.

5.Lift the right side of the agitator brush first and then lift the left hand side and lift the agitator brush out of the power head.

6.Carefully remove any belt residue that may exist in the belt area.

7.If the belt has broken, remove any loose pieces before replacing with a new belt.

8.Remove the worn or broken belt

from the motor drive shaft.

9Loop the new belt first over the motor drive shaft and then over the agitator pulley. (Fig. 23)

Insert

First

10.Insert the left side of the agitator in first by placing the end cap down into the slot and then do the same with the right side. Press firmly to make sure that each end is completely inserted.

11.Check to make sure that the belt is centered on the pulley and that the agitator turns freely.

12.Replace the top cover over the power head base and lock in place by turning the two screw locks clockwise until you hear them lock in place.

Changing the Headlight Bulb

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, HEPA filter,changing the filters or performing maintenance/trouble shooting checks.

1.Turn unit “Off” and unplug from wall outlet.

2.With a flat head screw driver, snap off the lens cover by pressing down on the two notches on the lens cover. (Fig. 24)

3.Lift off the head light lens.

Notches

Fig. 24

4.Remove the light bulb by pulling it out carefully.

5.Replace the new bulb by pushing it in.

6.Replace the head light lens by pushing it in so that it snaps back in place.

4

5.When using the attachments, the vacuum must be in the upright position. (Fig. 3)

Fig. 23

9

Image 6
Contents Bagless Upright Vacuum Model UV209HMain Mill Street, Door Plattsburgh, NY 800 Ownership Registration Card Model UV209HImportant Safety Instructions Rev /03DCyclonic Bagless Upright To Order Replacement Filters or BeltsPrecautionary Measures Or for Technical Support For Model UV209HProblem Solving Getting to Know Your Bagless Cyclonic UprightOperating Instructions Motor Thermostat Using the Air Driven Turbo BrushCleaning Air Driven Turbo Brush Carpet Height SelectorCleaning the Filter Ring Cleaning the Hepa Dust Cup FilterCleaning the Hepa Filter Frame Cleaning the Secondary Filter

UV209H specifications

The Euro-Pro UV209H is a cutting-edge handheld vacuum that merges powerful suction capabilities with advanced filtration technologies, making it an ideal choice for both everyday cleaning tasks and more specialized cleaning needs. Designed with the modern user in mind, it boasts a compact and lightweight design, allowing for easy maneuverability and storage.

At the heart of the UV209H is its robust motor, which provides impressive suction power. This ensures that dirt, dust, and debris can be easily lifted from various surfaces, including carpets, upholstery, and hard floors. The vacuum's versatility is complemented by multiple attachments, such as crevice tools and upholstery brushes, designed to tackle a wide range of cleaning challenges.

One of the standout features of the Euro-Pro UV209H is its innovative HEPA filtration system. This advanced technology captures 99.97% of dust and allergens, making it an excellent choice for allergy sufferers and families with pets. The washable filter not only enhances the vacuum’s performance but also contributes to a more eco-friendly cleaning experience, as users can easily maintain it without the need for frequent replacements.

The Euro-Pro UV209H is also designed with user convenience in mind. It features a large dustbin that minimizes the frequency of emptying, allowing for longer cleaning sessions without interruption. The vacuum's ergonomic handle and controls ensure comfortable usage, reducing strain during extended periods of operation.

Additionally, the vacuum is equipped with a powerful lithium-ion battery, offering cordless operation for maximum flexibility and ease of use. This feature is particularly advantageous for cleaning hard-to-reach areas or taking the vacuum outside without the hassle of cords.

Durability is another key characteristic of the Euro-Pro UV209H. It is constructed with high-quality materials designed to withstand regular use, ensuring that it remains a reliable cleaning companion for years to come.

In summary, the Euro-Pro UV209H combines powerful suction, advanced HEPA filtration, and user-friendly features, making it a top choice for anyone looking to maintain a clean and healthy living environment. Its thoughtful design and innovative technologies make cleaning not only effective but also enjoyable.