Hoover U5182900 owner manual Agitator brush roll, Lubrication

Page 9

3-14

3-15

3-16

B

Rotate hood toward front of cleaner and remove the hood.

Removing agitator brush roll

Remove agitator brush roll and used belt.

Discard used belt.

Installing new belt

With lettering on outside of belt, slide new belt over motor pulley (B).

3-17

C

Replacing agitator brush roll

Insert agitator through belt and place belt in belt guide (C) on agitator.

3-18

E

D

Securing agitator

Grasp agitator firmly and fit it into position by first sliding end opposite the belt into the rectangular slot (D) on side of cleaner.

Pull other side of agitator (E) into place.

Turn agitator making sure belt turns freely and is not pinched between agitator and bottom of cleaner.

3-19

F

G

Replacing hood

Align tabs (F) on hood with slots (G) on base of cleaner. Pivot hood into position.

Secure hood into position by turning the coin slots (Fig. 3-13).

The agitator brush roll

When to replace

When agitator brushes are worn, the agitator should be replaced.

To check condition of brushes, dis- connect cleaner from electrical outlet.

3-20

Move edge of a card across bottom plate while turning agitator. To main- tain cleaning effectiveness, replace agitator if brushes do not touch card.

What to buy

When purchasing a new agitator, ask for HOOVER part No. 48414115.

How to replace

Disconnect cleaner from electrical outlet.

Remove hood, belt and agitator fol- lowing directions in “The belt” sec- tion beginning with Fig. 3-13.

Discard old agitator.

Continue following the directions in “The belt” section to reposition belt, new agitator and hood.

Lubrication

The motor is equipped with bear- ings that contain sufficient lubrica- tion for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to motor bearings.

Continued

 

9

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents
This product was designed for easy assembly see Review this manual before Operating the cleanerEnglish ‹pp Hoover.comContents Important SafeguardsCarton contents Cleaner assemblyON-OFF switch Cleaner descriptionTransporting cleaner Position toolsCarpet height adjustment Carrying cleanerSettings Cleaning lightweight flexible rugsCleaning tools Cyclonic filter assembly Dirt cupSecondary filter Belt replacement Final filterHeadlight replace- ment Lubrication Agitator brush rollAgitator brush roll replacement Powered hand toolBelt replacement Inspect the belt Replace beltThermal protector ServiceChecking under hood Turn cleaner OFF and unplug Full One Year WarrantyClearing blockages Domestic UseÍndice Aspiradora vertical ciclónica¡Guarde estas instrucciones Lea este manual antes de hacer funcionar la aspiradoraCómo usar la aspiradora Ensamblado de la aspiradoraTraslado de la aspiradora Mango telescópicoPara transportar la aspiradora Posiciones del mangoColocación del tubo de extensión y de los accesorios MantenimientoAccesorio combinado Limpieza de los filtrosReemplazo de la luz delantera LubricaciónReemplazo de la correa El rodillo de escobillas del agitadorProtector térmico Si tiene un problemaServicio Reemplazo de la correaEliminación de obstrucciones Revisión del paso del flujo de aireRevisión debajo de la cubierta Uso doméstico Garantía de un año CompletoContenu Aspirateur vertical cycloniqueMerci d’avoir choisi un produit Hoovermd Ce produit a été conçu pour un assemblage facile voirUtilisation Assemblage de l’aspirateurChoix de l’accessoire approprié Accessoires de nettoyageTransport de l’aspirateur Positions du mancheEntretien Lubrification Remplacement de la courroieRemplacement de la courroie Remplacement de la courroieDépannage Protecteur thermiqueGarantie complète De un an Déblocage des obstructionsVérifier le débit d’air Vérifier sous le couverclePage East Maple St North Canton, OH Attn Sales & Service Center Número No. en Costo No.de De pieza Paqte Desprenda esta sección y envíela por Correo a$7.50 Hoover Company North Canton, OH