Black & Decker PM1000, 90503695 Installation Instructions, Operating Instructions

8

15

9

13

14

19

18

10 A	16	10 B
7	10	C
	17
6
11	11 A

	52” min
	132 cm	1”
		25 cm
12 A	12 D
12D	12 B	2
	2
	1
	12 C
	2

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Features

*Depending on model purchased, your unit may not appear exactly as shown.

*BEFORE FIRST USE remove all components from the packaging and familiarize yourself with them to help you with the assembly and operation of your Power Mop.

Assembling the Power Mop Unit

•Snap Yoke Rod (8) into the Conversion Bar Link (9) as shown in Fig. 2.

•Install the Handle Section (2) by ensuring that the Connector Key (10) matches the shape of the Notch in the Main Unit Tube (11) before inserting and snapping in place. Push Handle Section until you hear a “click” sound to ensure it is properly assembled with Main Unit Tube. (see Fig. 3)

•Unscrew Thumbscrew (3) from Slider (12) and insert Conversion Bar (13) into Slider as shown in Fig. 4. Re-installThumbscrew and hand tighten.

•Install the Brush (5) by lining up the shape of the end of the accessory with the shaft and push it on, until it snaps in place. See Fig. 5 for reference. To remove the Brush, simply pull it off.

WARNING: Do not attach/remove accessory when unit is running.

•Convert the unit from Scrubbing Mode to Mop Mode as shown in Fig. 6.

•Install Pad Holder (7) to Yoke (14) as shown in Fig. 7. Push it in until you hear a “click” sound.

Battery Installation

Note: Before installing batteries, ensure the Power Mop is in Mop Mode. See section How to Convert the Unit for proper mode conversion.

CAUTION: Use caution when removing batteries as they may become hot if the unit is used in scrubbing mode for extended periods of time.

Remove the Battery Compartment (15) by pushing the tab and rotating up as shown in Fig. 8. Insert four fresh alkaline AA batteries making sure to match (+) and (-) terminals correctly. Insert batteries as shown in Fig. 9 starting with the ones close to cover first.

Re-install the battery compartment into unit. Use alkaline batteries only.

WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:

•Carefully follow all instructions and warnings on the battery label and package.

•Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the equipment.

•Do not short battery terminals.

•Do not charge batteries.

•Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type.

•Remove dead batteries immediately and dispose of per local codes.

•Do not dispose of batteries in fire.

•Keep batteries out of reach of children.

•Remove batteries if the device will not be used for several months.

•Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.

Installation and Ejection of “No Touch” Cleaning Pads

“No Touch” Pad Installation

1.To attach the Cleaning Pad the Power Mop needs to be in Mop Mode. See section How to Convert the Unit for proper mode conversion.

2.Place the Cleaning Pad (6) on the floor with the fabric side touching the floor surface as shown in Fig. 10A.

3.Bring the Pad Holder (7) over the Cleaning Pad and insert it inside the Cleaning Pad.

4.Apply a small pressure on the Pad Holder to secure the pad in place.

Cleaning Pad Ejection

1.To eject, raise the Pad Holder above the floor and turn the Pad Holder Knob (16) (Fig. 10B) in the direction indicated by the arrow.

2.Dispose of the Cleaning Pad

Note: It might be possible to recycle the Cleaning Pad in your area. Verify with your local recycling organization to inquire about it.

The Power Mop also accepts common disposable pads as well as common washable and reusable pads (i.e. Microfiber cloths). These pads can readily be found in most retail stores.

Installation and Removal of Generic Cleaning Pads

To install Generic Pads:

1.Lay the pad flat on the floor.

2.Center the Pad Holder of the Power Mop directly over the pad on the floor.

3.Wrap the edges of the pad around the sides of the Pad Holder to reach the Rubber Grippers (17) found on the top of the Pad Holder as shown in Fig. 10C.

4.Insert the edges of the pads, one at a time, into each of the 4 Rubber Grippers found on top of the Pad Holder. Use your finger to do this.

5.To remove dirty pad, simply pull pad out of Rubber Grippers.

Hanging the Unit

1.Find a stud within the wall where the unit will rest.

2.Insert a 2” (63.5 mm) finishing nail at 45 degree from at least 52” (1321 mm) to the floor. The nail head should extend 1” (25 mm) from the wall. See Fig. 11 and 11A for details.

OPERATING INSTRUCTIONS

How to Convert the Unit

12A - Mop Mode

12B - Scrubbing Mode

12C - Brush Installation / Removal Mode