GE GX1S04C Mounting Bracket to Cabinet Wall, Tubing Connections-Push-In Style Model GX1S15C

Page 7

Mounting Bracket to Cabinet Wall

The bracket can be used as a template for marking the location of the mounting screws. When determining the location of the bracket make sure you leave 1-1⁄2″ to 2″ of free area under the sumps to allow for sump removal and enough space on either side to make the tubing connections.

Tubing Connections—Compression Style

(Models GX1S04C and GN1S04C)

1 Run the length of 3⁄8″ tubing, connected to the bottom of faucet, to the filter system outlet. Allow enough slack in the tubing so the unit can be easily removed for filter changes. Measure and cut the end of the tubing square.

2 Slide a compression nut onto the end of the tubing and push a tubing insert into the tubing.

3 Connect the tubing and tighten the compression nuts securely.

4 Repeat the preceding steps to connect a length of tubing between the filter system inlet and the water supply/saddle valve (illustration in the Installation Overview section).

2-3⁄4

 

 

Tubing connector

 

(outlet)

Mounting

 

bracket

 

Tubing connector

Mounting

(inlet)

screws

Sump

 

1 -1⁄2 to 2

Tubing Connections—Push-In Style (Model GX1S15C)

1 Run the length of the 3⁄8″ tubing, connected to the bottom of the faucet, to the filter system outlet (illustration above). Allow enough slack in the tubing so that the unit can be easily removed.

2 Measure and cut the end of the tubing square using a sharp cutter or knife. Remove any burrs (illustration A).

3 Inspect the end of the tubing, about 1 inch, to be sure there are no imperfections. It may be necessary to cut the tubing again.

4 Mark the tubing for length of insertion. For 3/8″ OD tubing the insertion length should be approximately 3/4 of an inch. Tubing must be fully inserted to avoid leaks.

5 DO NOT REMOVE GRAY COLLET. Push the tubing all the way into the fitting until it bottoms out. The insertion line should be hidden or barely visible (illustration B and C). Slightly pull on the tubing to verify engagement.

6 Repeat the procedure to connect the tubing between the filter system inlet and the water supply/saddle valve (illustration in the Installation Overview section).

7 To remove tubing (illustration D), depress and hold gray collet. Pull tubing to remove.

NOTE: Avoid installing the unit where the tubing is pulled at a sharp angle. This type of installation may cause the fittings to leak. If using tubing other than what is supplied, be sure it is high quality, exact size and roundness, and has a smooth surface.

A

B

C

Cut tubing square

End of tubing round and smooth, with no cuts,

nicks or flat spots (approximately 1)

Gray Collet

(DO NOT REMOVE)

Insertion line

Tubing

 

3⁄4

Tubing must

 

be fully inserted

 

 

Insert

 

to avoid leaks.

Gray Collet

 

 

(DO NOT

 

 

REMOVE)

 

 

Insertion line

3 4"

 

Insert tubing

Engagement

3/4(3/8tubing)

D

Gray Collet

Tubing

Depress gray collet

 

and pull tubing

 

to remove

7

Image 7
Contents Part No C1044P010-1 Pub. No -50040-112-99 JR Filter Cartridge Installation orBefore You Call For Service Parts List/Catalog Service Telephone Numbers WarrantyWrite the model and serial numbers here Staple sales slip or cancelled check hereIs in the water Specification guidelinesAbout the water filtration system How much water you useInstallation Overview Tools and Materials Required for InstallationCheck and comply with local plumbing codes as you plan Optional Home Installation Where codes permitFeed Water Supply For 1/2 OD or larger metal tubing onlyFaucet Installation Step-by-step installation instructionsNeeded Tubing Connections-Push-In Style Model GX1S15C Mounting Bracket to Cabinet WallFilters should be changed every six months Filter Cartridge Installation or ReplacementProcedure for flushing the GE Water Filtration system is Flush ProcedureCircumstances that may require flushing the system are Problem Possible Causes Before you call for service…General Electric parts catalog Parts ListWhat GE Will Not Cover Service Telephone NumbersGE Water Filtration System Warranty For The Period Of GE Will ReplaceConseils pour le diagnostic Instructions d’installationInformation de sécurité Instructions d’utilisation Agrafer ici le bordereau de vente ou chèque encaissé SI UN Dépannage EST NécessaireSubstances indésirables Volume de consommation d’eauDescription sommaire du système de filtration d’eau SpécificationsOutillage et matériel nécessaires pour l’installation Instructions d’installationRecommandations importantes concernant l’installation Illustration de l’installationSource d’alimentation du filtre Configuration D’INSTALLATION PréférentielleInstallation du robinet Étapes de l’installationRaccordement des tubes par enfoncement modèle GX1S15C Fixation de la bride de montage sur la paroi du placardUtilisation du système de filtration de l’eau Cartouches de filtration-Installation ou remplacementCirconstances qui peuvent nécessiter un rinçage du circuit Processus de rinçageMéthode de rinçage du système de filtration GE Problème Causes possibles Avant de contacter un dépanneur…Catalogue des pièces General Electric Liste des piècesCe que la garantie GE ne couvre pas Numéros de serviceSystème de filtration d’eau GE-Garantie Pendant une période de GE remplaceraAntes de llamar para un servicio Instrucciones de instalaciónEscriba los números de modelo y serie aquí Engrape el recibo de venta o el cheque cancelado aquíGuía de especificaciones Acerca del sistema de filtración de aguaSumario de la instalación Instrucciones de instalaciónRecomendaciones importantes de instalación Herramientas y Materiales requeridas para la instalaciónPara un tubo OD de 1/2 o más grande solamente Línea de abastecimiento de aguaPara un tubo OD de 1/2 o más grande solamente Instalacion DE Casa Opcional donde lo permitan los códigosInstalación de llaves de agua Instrucciones de instalación paso a pasoConexiones de los tubos-Estilo empuje Modelo GX1S15C Cómo montar la abrazadera en la pared del gabineteGN1S04C Conexiónes de los tubos-Estilo compresión Modelos GX1S04CCartucho Instalación o reemplazo del cartucho del filtroProcedimiento para lavar Agua y está turbia Problema Posibles causasAntes de llamar para un servicio Agua tiene burbujas deCatálogo de partes General Electric Lista de partesDe Massachusetts Lo que GE no cubrirá Números de servicioGarantía del sistema de Filtración de Agua GE Por el período de GE reemplazará

GN1S04C, GX1S15C, GX1S04C specifications

The GE GN1S04C, GX1S15C, and GX1S04C are advanced gas-powered refrigerators designed for commercial use, making them the ideal choice for various business environments, including restaurants and catering services. Each model boasts unique features and technologies that cater to specific needs, ensuring optimal performance and reliability.

Starting with the GN1S04C, this refrigerator is known for its spacious interior and energy-efficient design. With a generous capacity of 400 liters, it can easily accommodate a large volume of food items, making it perfect for busy kitchens. The GN1S04C is equipped with a powerful compressor that ensures rapid cooling and temperature stability. The adjustable shelving allows for customizable storage options, while the stainless-steel exterior provides durability and easy maintenance. Additionally, the model features a digital temperature control system that allows users to monitor and adjust settings with precision.

Moving on to the GX1S15C, this model stands out due to its innovative temperature management technology. It is designed with multi-air flow systems that ensure even cooling throughout the unit, reducing the risk of hot spots. With an impressive capacity of 420 liters, it offers ample space for storage. One of its key features is the advanced electronic control that includes an energy-saving mode, optimizing efficiency during low-demand periods. The GX1S15C also prioritizes user convenience with its easy-to-read digital display and intuitive interface.

Lastly, the GX1S04C complements the lineup with its compact design, making it suitable for smaller kitchen spaces without compromising on performance. This model features a user-friendly design with well-designed shelving that maximizes storage space. The GX1S04C is also robustly constructed, ensuring resistance against wear and tear, essential for a busy commercial kitchen. It offers seamless temperature regulation thanks to its advanced refrigeration technology, which maintains food safety standards even during peak hours.

Together, these models showcase GE's commitment to quality, efficiency, and innovation in commercial refrigeration. Their distinct characteristics, such as spacious interiors, energy-saving technologies, and robust construction, make the GN1S04C, GX1S15C, and GX1S04C top choices for businesses that require reliable refrigeration solutions. As industries continue to evolve, these models represent the forefront of gas-powered refrigeration technology, catering to the needs of modern kitchens.