Rheem Solar Loline Conversion Kit Electric Wter Heater Relief Valve Drain, Bleed Valve Drain

Page 30

CONNECTIONS - PLUMBING

RELIEF VALVE

The Temperature and Pressure Relief valve must be fitted before the water heater is operated. Before fitting the relief valve, make sure the probe has not been bent. Seal the thread with Teflon tape - never hemp. Make sure the tape does not hang over the end of the thread.

Screw the valve into the correct opening (refer to the installation diagram on page 23) leaving the valve outlet pointing downwards. Do not use a wrench on the valve body - use the spanner flats provided.

RELIEF VALVE DRAIN

A drain pipe must be fitted to the relief valve to carry the discharge clear of the water heater. Connect the drain line to the relief valve using a disconnection union. The pipe work from the relief valve to the drain should be as short as possible, and fall all the way from the water heater with no restrictions. It should have no more than three right angle bends in it. Use DN15 pipe. The outlet of the drain pipe must be in such a position that flow out of the pipe can be easily seen (refer to AS/NZS 3500.4.2) - but arranged so hot water discharge will not cause injury, damage or nuisance. The relief line must discharge at an outlet or air break not more than 9 metres from the relief valve.

In locations where water pipes are prone to freezing, the drain pipe must be insulated and not exceed 300 mm in length. In this instance, the drain pipe is to discharge into a tundish through an air gap of between 75 mm and 150 mm.

Warning: As the function of the Temperature and Pressure Relief valve on this water heater is to discharge high temperature water under certain conditions, it is strongly recommended the pipe work downstream of the relief valve be capable of carrying water exceeding 93￿C. Failure to observe this precaution may result in damage to pipe work and property.

BLEED VALVE DRAIN

A drain pipe must be fitted to the bleed valve to carry the discharge clear of the water heater and solar controls. Connect the drain line to the bleed valve using a disconnection union. The pipe work from the bleed valve to the drain should be as short as possible, and fall all the way from the valve with no restrictions. It should have no more than three right angle bends in it. Use DN15 pipe. The outlet of the drain pipe must be in such a position that flow out of the pipe can be easily seen (refer to AS/NZS 3500.4.2) - but arranged so water discharge will not cause injury, damage or nuisance. The water discharged may be of a high temperature under certain conditions.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Owners Guide Installation Instructions Patents Contents About Your Water Heater Model TypeHotter Water Increases the Risk of Scald Injury To Turn OFF the Water HeaterTo Turn on the Water Heater Does the Water Quality Affect the Water HEATER?HOW Long will the Water Heater LAST? Anode Protection Flushing the Solar Collectors Freeze ProtectionRegular Care Temperature and Pressure Relief ValveSafety Expansion Control ValveHOW Your Water Heater Works Mains PressureElectric Boosting Single Element Models Twin Element ModelsManual ON/OFF Switch Manual ControlsContinuous Tariff Connection ONE Shot Control Switch Going on HolidaysSave a Service Call Not Enough HOT Water or no HOT WaterWater not HOT Enough Continuous dribble Temperature and Pressure Relief Valve RunningNormal Operation Steady flows for long period often at nightHigh Electricity Bills Electricity TariffsCollector Glass Installation Solar Storage Tank Tank Water Supply Safe TrayMax. mains supply pressure HOT Water DeliverySaddling Pipe Work Reducing Heat LossesAnode Types Booster Heating UnitCold Water Inlet Assembly of Cold Water Supply and Solar Pipe ConnectionsHOT Water Outlet Relief ValveRheemglas Indoor Location Outdoor Location Installation Solar Control Unit Solar Conversion of a Rheem Electric Water HeaterSolar Storage Tank with Solar Control Unit Installation of Solar Collectors Supplied in Solar Loline Conversion KITInstallation Solar Collectors Solar Collector LocationLatitude of Some Australian Cities INLET/OUTLET Connections Connections PlumbingConnection Sizes Pipe SizesPipe Lengths Relief Valve Drain Bleed Valve DrainExpansion Control Valve Thermostat Setting Connections ElectricalManual Controls Commissioning To Fill and Turn on the Water HeaterBleeding the Solar Collectors To Turn OFF the Water Heater Draining the Solar Collectors Draining the Water HeaterPage Water Supplies AnodeRheem Solar Water Heater Warranty Australia only Cylinder from date of installation Rheem will

Solar Loline Conversion Kit Electric Wter Heater specifications

The Rheem Solar Loline Conversion Kit for electric water heaters is a remarkable solution that integrates solar energy into water heating systems, facilitating a more sustainable and efficient way to heat water. This innovative kit is designed specifically to convert existing electric water heaters into solar-compatible units, enabling homeowners to harness the power of the sun for their hot water needs.

One of the main features of the Rheem Solar Loline Conversion Kit is its compatibility with various electric water heater models. This flexibility allows homeowners to enhance their existing systems without the need for complete replacement, making it a cost-effective choice for many. The kit includes all necessary components required for the installation, including a solar controller, a solar pump, and the required plumbing fittings, ensuring a seamless upgrade process.

This conversion kit utilizes advanced technologies to maximize energy efficiency. The solar controller optimizes the operation of the system by monitoring the temperature of the water in the storage tank and the solar collectors, ensuring that the water is heated when sufficient solar energy is available. This intelligent management helps reduce electricity consumption, leading to significant savings on energy bills.

In terms of characteristics, the Rheem Solar Loline Conversion Kit boasts high-quality construction and reliable performance. The durable components ensure a long lifespan and minimal maintenance, making it a wise investment for environmentally-conscious homeowners. The solar pump, designed for efficiency, enhances the movement of water between the solar collectors and the storage tank, ensuring optimal heat transfer and system performance.

Moreover, the kit promotes sustainability by reducing reliance on fossil fuels and decreasing carbon emissions. By utilizing solar energy for water heating, homeowners can significantly lower their environmental impact while enjoying the benefits of hot water on demand.

In conclusion, the Rheem Solar Loline Conversion Kit for electric water heaters presents an excellent opportunity for homeowners to embrace solar energy. With its compatibility, advanced technologies, and eco-friendly characteristics, this conversion kit stands as an ideal solution for those looking to enhance their water heating systems while contributing to a greener future. Whether for new installations or retrofitting existing systems, the Rheem Solar Loline Conversion Kit is designed to meet modern demands for efficiency and sustainability.
Top Page Image Contents