Bunn FMD-1, FMD-2 service manual

Page 34

SERVICE (cont.)

SOLENOID VALVE (DISPENSE) - FMD-1 & FMD-2

J1

 

FMD-1

P1665

 

J1

 

FMD-2

 

FIG. 36 DISPENSE SOLENOID VALVE

P1666

 

Location:

 

The dispense solenoid is located on the upper left center of the tank.

Test Procedures:

1.Disconnect the dispenser from the power source.

2.For FMD-1 disconnect the red and white wires from the solenoid valve. For FMD-2 disconnect orange and white wires on the right solenoid or the tan and white wires on the left solenoid. With the “RINSE/RUN” switch in the "RINSE" upper position press the dispense switch on front of the door.

3.Check the voltage across the red and white, orange and white or tan and white wires with a voltmeter. Connect the dispenser to the power source. The indication must be 120 volts ac for two wire 120 volt models, three wire 120/208 and 120/240 volt models.

4.Disconnect the dispenser from the power source.

If voltage is present as described, proceed to #5

If voltage is not present as described, refer to wiring diagram and check dispenser wiring harness.

5.Check for continuity across the solenoid valve coil terminals.

If continuity is present as described, reconnect the wires to the solenoid (see Fig. 34), proceed to #6

If continuity is not present as described, replace the solenoid valve.

6.Check the solenoid valve for coil action. Connect the dispenser to the power source. With "RINSE/ RUN” switch in the "RINSE" upper position press the dispense switch and listen carefully in the vicinity of the solenoid valve for a "clicking" sound as the coil magnet attracts.

7.Disconnect the dispenser from the power source.

If the sound is heard as described and water will not pass through the solenoid valve, there may be a block- age in the water outlet before the solenoid valve or, the solenoid valve may require inspection for wear, and removal of waterborne particles.

If the sound is not heard as described, replace the solenoid valve.

Removal and Replacement:

1.Open dispenser door and remove the hopper(s)

2.Remove the two #8-32 screws securing the hop- per panel to the auger motor mounting panel and two #8-32 screws to the whipper mounting panel.

34

29112 101598

 

Page 33 Page 35
Image 34
Page 33 Page 35
Contents BUNNFMD-1 FMD-2 User Notices WarrantyIntroduction FMD-1 FMD-2FMD-1 only 00656.000028368.0001 Electrical HOOK-UP Initial SET-UPElectrical Requirements Plumbing RequirementsLiquid Level Control Rinse Timer FMD-2 onlyInitial Fill & Heat Running a Rinse SequenceHopper Motor Speed Adjustment FMD-1 CleaningAdjustments Cold Beverage SET-UP Optional FMD-2 onlyDraining the HOT Water Tank Product will not dispense TroubleshootingProblem Probable CauseProbable Cause Remedy FMD-1 Problem Probable CauseStat for testing procedures. See SeeProblem Probable Cause Remedy Refer to Service Lamp, see page 28 for lamp replacement Dispenser is making unusualContents ServiceComponent Access Auger Drive Components FMD-1Spacer Auger Motor Hopper Base Dust Seal Washer Retainer Clip Hopper AssemblyHopper Lid Retainer Clip Ing panelTo the rear of the auger motor mounting panel Auger Drive Components FMD-1Auger Drive Components FMD-2 Hopper Hopper Assy Remove dust seal 17 from auger motor Disconnect the wires from the auger motor 16 to be removedRemove auger motor and discard Ballast FMD-1 & FMD-2 LocationControl Board FMD-2 only Thermostat TerminalsService Dispense Switch Dispense Switchs FMD-1 & FMD-2 Dispense Switch Terminals P1449 FAN FMD-1 & FMD-2FMD-2 Frother and Whipper Motor FMD-1 shown & FMD-2 Whipper Motor Terminals P1221Hopper Drive Board FMD-1 only Hopper Drive BoardHopper Drive Board FMD-1 only Hopper Drive Board TerminalsLamp Replacement Refer to Fig Door Assy Upper Panel Lamp Holders Lower PanelLamp Starter and Socket Refer to Location Lamp Replacement Refer toAs assembly Level Control Board and Level Probe FMD-1 onlyReconnect the violet wire to terminal Level Control Board and Level Probe FMD-1 onlyRINSE/RUN Switch FMD-1 LocationWHI/RED to RINSE/RUN Switch FMD-2BLK from Main Harness WHI/BRN to YEL to Control Board J2-3 Solenoid Valve Cold Water OPTIONALFMD-2 only Cold Water Solenoid ValveFMD-1 Solenoid Valve Dispense FMD-1 & FMD-2 Solenoid Valve Inlet FMD-1 & FMD-2 Tank HeaterTank Heater FMD-1 shown & FMD-2 Main Harness ThermostatTransformer FMD-2 only WHI/GRN T7 WHI/BLK T12Schematic Wiring Diagram FMD-1 Single PhaseSchematic Wiring Diagram FMD-2
Related manuals
Manual 8 pages 61.25 Kb

FMD-2, FMD-1 specifications

The Bunn FMD-2 is an advanced coffee dispensing machine designed for high-traffic environments, such as cafés, restaurants, and convenience stores. This commercial coffee equipment stands out for its reliability, efficiency, and user-friendly features, making it a preferred choice among coffee retailers.

A standout feature of the FMD-2 is its dual coffee bean hopper system, which allows for the storage and dispensing of two different coffee blends simultaneously. This versatility provides establishments the opportunity to cater to varying customer preferences, whether they prefer a robust espresso or a smooth medium roast. The hoppers can hold a significant amount of coffee beans, ensuring that the machine can keep up with high demand without the need for frequent refilling.

The FMD-2 incorporates state-of-the-art brewing technology, including the ability to brew coffee quickly while preserving the essential flavor characteristics of the beans. Its precision brewing process ensures consistency in taste and quality, which is crucial for customer satisfaction in a commercial setting. The machine is equipped with adjustable brew times and temperatures, allowing operators to fine-tune the brewing process according to specific coffee styles or customer preferences.

Another notable characteristic of the Bunn FMD-2 is its digital interface, which features an intuitive touchscreen display. This modern interface simplifies the operation of the machine, enabling baristas and staff to quickly train and adapt to its functionalities. The display provides real-time feedback on brewing status, maintenance reminders, and settings adjustments, making it easier to ensure optimal performance and reduce downtime.

In addition to its user-friendly design, the Bunn FMD-2 is constructed for durability. Its stainless steel exterior not only enhances its aesthetic appeal but also ensures that it can withstand the rigors of daily use in a bustling environment. The machine is designed with easy maintenance in mind, allowing for straightforward cleaning and servicing to keep it operating at peak performance.

Overall, the Bunn FMD-2 is a versatile, reliable, and innovative coffee dispensing solution that meets the demands of today’s coffee enthusiasts. With its dual hopper system, precision brewing technology, and user-friendly interface, it’s an ideal choice for any establishment looking to elevate their coffee offerings and enhance customer experience.
Top Page Image Contents