Bunn service manual FAN FMD-1 & FMD-2, Dispense Switch Terminals P1449

Page 23

SERVICE (cont.)

DISPENSE SWITCH(S) - FMD-1 & FMD-2 (cont.)

BLK

 

RED

 

 

FMD-1

BLK

 

RED/WHI

BLK

 

RED

 

 

RIGHT

 

ORN

 

BLK/WHI

ORN

LEFT

FMD-2

BLU/WHI

FIG. 14 DISPENSE SWITCH TERMINALS P1449

FAN - FMD-1 & FMD-2

P1665

FIG. 15 FAN

Location:

The fan is located inside the dispenser hous- ing on the right rear of the dispenser base plate.

Test Procedures:

1.Disconnect the dispenser from the power source.

2.Disconnect the black and white wires from the fan terminals.

3.Check the voltage across the black and white wires on the main harness with a voltmeter. Connect the dispenser to the power source. The indication must be:

a)120 volts ac for two wire 120 volts models.

b)120 volts ac for three wire 120/208 volt or 120/ 240 volt models.

If voltage is present as described, replace the fan

If voltage is not present as described, refer to wiring diagram and check the dispenser wiring harness.

Removal and Replacement:

1.Disconnect the vacuum hose from the fan.

2.Remove the two #8-32 locking screws securing the fan to the dispenser housing base plate.

3.Disconnect the wires from the fan terminals and discard the fan

4.Refer to Fig. 16 and connect the wires to the new fan.

5.Install new fan through the rear access hole and secure to the dispenser housing base plate using two #8-32 locking screws.

6.Reconnect the vacuum hose to the fan.

 

BLK from Control Harness

 

WHI from Control Harness

 

P1507

 

FIG. 16 FAN TERMINALS

23

29112 101598

 

Image 23
Contents BUNNFMD-1 FMD-2 FMD-1 FMD-2 WarrantyIntroduction User Notices28368.0001 00656.0000FMD-1 only Plumbing Requirements Initial SET-UPElectrical Requirements Electrical HOOK-UPRunning a Rinse Sequence Rinse Timer FMD-2 onlyInitial Fill & Heat Liquid Level ControlCold Beverage SET-UP Optional FMD-2 only CleaningAdjustments Hopper Motor Speed Adjustment FMD-1Draining the HOT Water Tank Probable Cause TroubleshootingProblem Product will not dispenseProbable Cause Remedy See Problem Probable CauseStat for testing procedures. See FMD-1Problem Probable Cause Remedy Dispenser is making unusual Refer to Service Lamp, see page 28 for lamp replacementAuger Drive Components FMD-1 ServiceComponent Access ContentsRetainer Clip Ing panel Retainer Clip Hopper AssemblyHopper Lid Spacer Auger Motor Hopper Base Dust Seal WasherAuger Drive Components FMD-2 Auger Drive Components FMD-1To the rear of the auger motor mounting panel Hopper Hopper Assy Remove auger motor and discard Disconnect the wires from the auger motor 16 to be removedRemove dust seal 17 from auger motor Location Ballast FMD-1 & FMD-2Thermostat Terminals Control Board FMD-2 onlyService Dispense Switch Dispense Switchs FMD-1 & FMD-2 FAN FMD-1 & FMD-2 Dispense Switch Terminals P1449FMD-2 Whipper Motor Terminals P1221 Frother and Whipper Motor FMD-1 shown & FMD-2Hopper Drive Board Hopper Drive Board FMD-1 onlyHopper Drive Board Terminals Hopper Drive Board FMD-1 onlyDoor Assy Upper Panel Lamp Holders Lower Panel Lamp Replacement Refer to FigLevel Control Board and Level Probe FMD-1 only Lamp Replacement Refer toAs assembly Lamp Starter and Socket Refer to LocationLevel Control Board and Level Probe FMD-1 only Reconnect the violet wire to terminalLocation RINSE/RUN Switch FMD-1BLK from Main Harness WHI/BRN to YEL to Control Board J2-3 RINSE/RUN Switch FMD-2WHI/RED to Cold Water Solenoid Valve Solenoid Valve Cold Water OPTIONALFMD-2 onlyFMD-1 Solenoid Valve Dispense FMD-1 & FMD-2 Tank Heater Solenoid Valve Inlet FMD-1 & FMD-2Main Harness Thermostat Tank Heater FMD-1 shown & FMD-2WHI/GRN T7 WHI/BLK T12 Transformer FMD-2 onlySingle Phase Schematic Wiring Diagram FMD-1Schematic Wiring Diagram FMD-2
Related manuals
Manual 8 pages 61.25 Kb

FMD-2, FMD-1 specifications

The Bunn FMD-2 is an advanced coffee dispensing machine designed for high-traffic environments, such as cafés, restaurants, and convenience stores. This commercial coffee equipment stands out for its reliability, efficiency, and user-friendly features, making it a preferred choice among coffee retailers.

A standout feature of the FMD-2 is its dual coffee bean hopper system, which allows for the storage and dispensing of two different coffee blends simultaneously. This versatility provides establishments the opportunity to cater to varying customer preferences, whether they prefer a robust espresso or a smooth medium roast. The hoppers can hold a significant amount of coffee beans, ensuring that the machine can keep up with high demand without the need for frequent refilling.

The FMD-2 incorporates state-of-the-art brewing technology, including the ability to brew coffee quickly while preserving the essential flavor characteristics of the beans. Its precision brewing process ensures consistency in taste and quality, which is crucial for customer satisfaction in a commercial setting. The machine is equipped with adjustable brew times and temperatures, allowing operators to fine-tune the brewing process according to specific coffee styles or customer preferences.

Another notable characteristic of the Bunn FMD-2 is its digital interface, which features an intuitive touchscreen display. This modern interface simplifies the operation of the machine, enabling baristas and staff to quickly train and adapt to its functionalities. The display provides real-time feedback on brewing status, maintenance reminders, and settings adjustments, making it easier to ensure optimal performance and reduce downtime.

In addition to its user-friendly design, the Bunn FMD-2 is constructed for durability. Its stainless steel exterior not only enhances its aesthetic appeal but also ensures that it can withstand the rigors of daily use in a bustling environment. The machine is designed with easy maintenance in mind, allowing for straightforward cleaning and servicing to keep it operating at peak performance.

Overall, the Bunn FMD-2 is a versatile, reliable, and innovative coffee dispensing solution that meets the demands of today’s coffee enthusiasts. With its dual hopper system, precision brewing technology, and user-friendly interface, it’s an ideal choice for any establishment looking to elevate their coffee offerings and enhance customer experience.