Desa FB-3B Attaching Mounting Bracket To Wall, Placing Heater On Mounting Bracket

Page 9

OWNER’S MANUAL

INSTALLATION

Continued

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hard- ware package is provided with heater.

Attaching to Wall Stud Method

For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64" drill bit.

2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket is firmly fastened to wall studs.

Attaching to Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.

2.Fold wall anchor as shown in Figure 10.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 11). IMPORTANT: Do not hammer key!For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Figure 10 - Folding Anchor

Figure 11 - Popping Open Anchor Wings For Thin Walls

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater (see Figure 12).

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Horizontal Slots

Stand-Out Tab

Mounting Bracket

(attached to wall)

 

Figure 12 - Mounting Heater Onto Mounting Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 13).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 un- der Attaching To Wall Anchor Method. If installing bottom mounting screw into wall stud, drill holes at marked lo- cations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mount- ing holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 10 and 11).

Figure 13 - Installing Bottom Mounting Screws

Continued

105567

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS Infrared VENT-FREE PROPANE/LP GAS HeaterInfrared PROPANE/LP GAS Heater Safety InformationProduct Identification Product FeaturesLocal Codes UnpackingProducing Adequate Ventilation Fresh AIR for Combustion and VentilationUnusually Tight Construction Confined and Unconfined SpaceFresh AIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Items InstallationInstalling Thermostat Sensing Bulb Check GAS TypeMounting Bracket Installing Heater to WallMethods For Attaching Mounting Bracket To Wall Marking Screw LocationsInstalling Bottom Mounting Screws Attaching Mounting Bracket To WallPlacing Heater On Mounting Bracket Typical Inlet Pipe Diameters Connecting to GAS SupplyOperating For Your SafetyHeater Checking GAS ConnectionsOperating Heater Manual Lighting ProcedureLighting Instructions To Select Heating LevelPress in control knob and turn coun For Your Safety Read Before LightingInspecting Burner Cleaning and MaintenanceObserved Problem Possible Cause Remedy TroubleshootingInfrared PROPANE/LP GAS Heater Top Parts Centrals SpecificationsService Hints Replacement PartsService Publications Accessories Technical ServiceODS/Pilot Assembly Burner Assembly Illustrated Parts BreakdownFB-3B KEY FB-3B Description Parts ListFB-5B Burner Assembly ODS/Pilot AssemblyKEY FB-5B Description FBS-3C KEY FBS-3B Description QTY FBS-5B KEY FBS-5B Description QTY FBS-5CInternational Warranty Information

FB-3B specifications

Desa FB-3B is an innovative muscle-building device that has gained recognition in the fitness community for its effectiveness and ease of use. Designed to cater to fitness enthusiasts of all levels, the FB-3B integrates advanced technology with ergonomic features that enhance the workout experience.

One of the standout characteristics of the Desa FB-3B is its compact design. This makes it suitable for home gyms, commercial fitness centers, or even smaller workout spaces without compromising on functionality. The frame is constructed from high-strength steel, ensuring durability and stability during intense workout sessions. Its sleek design not only appeals aesthetically but also maximizes the user’s workout area.

The FB-3B offers a multi-functional workout experience thanks to its adjustable resistance settings. Users can easily modify the resistance according to their fitness levels, which allows for personalized training experiences. This feature is particularly beneficial for progressive training, where users can gradually increase the load as they build strength.

Another critical aspect of the Desa FB-3B is its integrated digital monitoring technology. The built-in LCD screen tracks key performance metrics such as time, repetitions, and calories burned. This real-time feedback aids users in setting and achieving their fitness goals, creating a more structured and goal-oriented workout regime.

Comfort is also prioritized in the design of the FB-3B. It features padded seats and backrests made from high-density foam, promoting proper posture and reducing the risk of injury during workouts. The non-slip footrests provide extra safety, allowing users to focus on their exercises without distractions.

Moreover, the FB-3B includes various attachment options, enabling users to target specific muscle groups effectively. From leg extensions to lat pull-downs, this versatility makes the FB-3B ideal for comprehensive strength training.

In conclusion, the Desa FB-3B combines durability, functionality, and user-friendly technology to create a versatile fitness solution for anyone looking to enhance their strength training regimen. Whether you’re a beginner or an experienced athlete, the FB-3B offers features that allow for an effective and enjoyable workout experience.
Top Page Image Contents