Desa VN10T installation manual Attaching to wall anchor method, Placing Heater On Mounting Screws

Page 7

OWNER’S MANUAL

INSTALLING TO WALL

Continued

Installing Two Mounting Screws

Note: Wall anchors and mounting screws are in hardware package. The hardware pack- age is provided with heater.

Attaching to wall stud method

For attaching mounting screw to wall stud

1.Drill hole at marked location using 9/64" drill bit.

2.Insert mounting screw into wall stud.

3.Tighten screw until 1/16" space (thick- ness of penny) is between screwhead and wall.

Attaching to wall anchor method

Follow instructions below to attach mount- ing screws to hollow walls (wall areas be- tween studs) or solid walls (concrete or masonry).

5.Tighten two screws until 1/16" space (thickness of penny) is between screwheads and wall (see Figure 8).

Thin or Thick Wall

(thick wall

shown)

1/16" Space

Solid

Wall

ANCHOR

Figure 8 - Tightening Anchors

Placing Heater On Mounting Screws

1.Locate two keyhole slots on back panel of heater (see Figure 9).

2.Place large openings of slots over screwheads. Slide heater down until screws are in small portion of slots.

Installing Bottom Mounting Screw

1.Locate bottom mounting hole. This hole is near bottom on back panel of heater (see Figure 11).

2.Mark screw location on wall.

3.Remove heater from wall.

4.If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 5 under Attaching To Wall Anchor Method.

If installing bottom mounting screw into wall stud, drill hole at marked lo- cation using 9/64" drill bit.

5.Replace heater on wall.

6.Insert bottom anchor screw through back panel into bottom anchor or drilled hole (see Figure 11).

7.Tighten screw until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 8 and 9).

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1 1/4" deep.

2.Fold wall anchor (see Figure 6).

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

Figure 6 - Folding Anchor

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 7). IMPORTANT: Do not hammer key!

For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

Thin Walls (1/4" to 1/2"

thick)

Keyhole Slots

Figure 9 - Location Of Keyhole Slots On Back Panel Of Heater

Removing Front Panel Of Heater

1.Remove two screws near bottom cor- ners of front panel.

2.Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4".

3.Pull bottom of front panel forward, then down.

Figure 11 - Installing Bottom Mounting Screw

Figure 7 - Popping Open Anchor Wings

Figure 10 - Removing Front Panel Of

For Thin Walls

Heater

102490

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Infrared VENT-FREE Natural GAS Heater OWNER’S Operation and Installation ManualModel VN10T Vanguard VN10T Natural GAS Heater Safety InformationLocal Codes Product FeaturesProduct Identification AIR for Combustion and VentilationDetermining if You Have a Confined or Unconfined Space Determining AIR Flow for Heater LocationUnusually Tight Construction Confined and Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type Installing to WallInstallation Items Installing Heater to WallRemoving Front Panel Of Heater Installing Bottom Mounting ScrewAttaching to wall anchor method Placing Heater On Mounting ScrewsPressure will occur Connecting to GAS SupplyChecking GAS Connections Pressure Testing GAS Supply Piping SystemPressure Testing Heater GAS Connections For Your Safety Read Before LightingTo Turn OFF GAS To Appliance Manual Lighting ProcedureLighting Instructions Thermostat Control OperationInspecting Burner Cleaning and MaintenanceObserved Problem TroubleshootingPossible Cause Remedy Observed Problem Possible Cause Remedy Top Observed Problem Possible CauseGas leak. See Warning statement at Service Publications SpecificationsReplacement Parts Technical ServiceVN10T Illustrated Parts ListODS/PILOT Parts Available not Shown Vanguard VN10T Natural GAS Heater 102490 Limited Warranty Vanguard VENT-FREE Residential GAS Heaters Warranty Information

VN10T specifications

The Desa VN10T is a sophisticated and versatile piece of machinery designed for various agricultural applications. Known for its robust construction and advanced technology, the VN10T stands out in the market for its efficiency and reliability. This model is particularly favored by farmers looking for a tractor that can handle challenging terrains while providing optimal performance.

One of the standout features of the Desa VN10T is its powerful engine. The tractor is equipped with a high-performance diesel engine that ensures not only substantial horsepower but also excellent torque delivery. This makes it particularly suited for heavy-duty tasks such as plowing, tilling, and hauling materials over uneven surfaces. The engine is designed with fuel efficiency in mind, allowing for longer working hours without the need for frequent refueling.

The VN10T features a user-friendly transmission system, providing smooth shifting and excellent control over various speed ranges. This adaptability allows operators to easily switch between tasks, increasing productivity on the farm. The four-wheel drive option enhances traction and stability, making it ideal for diverse agricultural practices, from planting to harvesting.

Technologically, the Desa VN10T is equipped with an advanced hydraulic system. This system allows for precise control of implements, facilitating a seamless execution of farming tasks. The hydraulic capabilities enable the use of various attachments, such as front loaders, backhoes, and mowers, transforming the tractor into a multipurpose tool on the farm.

Comfort and ease of use are also paramount in the design of the VN10T. The operator's cabin is spacious and ergonomically designed, coming with adjustable seating, intuitive controls, and climate control options. Visibility is enhanced through large windows, ensuring the operator can maneuver the tractor safely and effectively.

In terms of maintenance, the VN10T is designed for ease of access, simplifying routine checks and repairs. This reduces downtime and ensures that farmers can keep their operations running smoothly.

Overall, the Desa VN10T combines power, comfort, and advanced technology, making it an excellent choice for modern agricultural needs. Its ability to adapt to various tasks while maintaining efficiency sets it apart as a reliable partner for farmers.
Top Page Image Contents