Desa VN10TA installation manual Installing Two Mounting Screws, Placing Heater On Mounting Screws

Page 8

®

NATURAL GAS HEATER

INSTALLATION

Continued

Installing Two Mounting Screws

Note: Wall anchors and mounting screws are in hardware package. The hardware package is provided with heater.

Attaching To Wall Stud Method

For attaching mounting screw to wall stud

1.Drill hole at marked location using 9/64" drill bit.

2.Insert mounting screw into wall stud.

3.Tighten screw until 1/16" space (thick- ness of penny) is between screwhead and wall.

Attaching To Wall Anchor Method

Follow instructions below to attach mount- ing screws to hollow walls (wall areas be- tween studs) or solid walls (concrete or masonry).

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1 1/4" deep.

2.Fold wall anchor (see Figure 6).

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 7).

IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Tighten two screws until 1/16" space (thickness of penny) is between screwheads and wall (see Figure 8).

Thin or Thick Wall

(thick wall

shown)

1/16" Space

Solid

Wall

ANCHOR

Figure 8 - Tightening Anchors

Placing Heater On Mounting Screws

1.Locate two keyhole slots on back panel of heater (see Figure 9).

2.Place large openings of slots over screwheads. Slide heater down until screws are in small portion of slots.

Keyhole Slots

Figure 9 - Location Of Keyhole Slots On Back Panel Of Heater

Removing Front Panel Of Heater

1.Remove two screws near bottom cor- ners of front panel.

2.Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4".

3.Pull bottom of front panel forward, then down.

Installing Bottom Mounting Screw

1.Locate bottom mounting hole. This hole is near bottom on back panel of heater (see Figure 11).

2.Mark screw location on wall.

3.Remove heater from wall.

4.If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 5 un- der Attaching To Wall Anchor Method.

If installing bottom mounting screw into wall stud, drill hole at marked lo- cation using 9/64" drill bit.

5.Replace heater on wall.

6.Insert bottom anchor screw through back panel into bottom anchor or drilled hole (see Figure 11).

7.Tighten screw until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 9 and 10).

Figure 6 - Folding Anchor

Figure 11 - Installing Bottom Mounting

 

Screw

Thin Walls (1/4" to 1/2" thick)

Figure 7 - Popping Open Anchor Wings

Figure 10 - Removing Front Panel Of

For Thin Walls

Heater

 

8

104086

Page 7 Page 9
Image 8
Page 7 Page 9
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASSafety Information Natural GAS HeaterProduct Features Product IdentificationLocal Codes UnpackingAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Installation Installation ItemsInstalling Heater to Wall Locating HeaterInstalling Two Mounting Screws Installing Bottom Mounting ScrewPlacing Heater On Mounting Screws Removing Front Panel Of HeaterConnecting to GAS Supply Gas ConnectionFor Your Safety Read Before Lighting Pressure Testing Gas Supply Piping SystemPressure Testing Heater Gas Connections Operating HeaterManual Lighting Procedure Lighting InstructionsThermostat Control Operation To Turn OFF GAS To ApplianceCleaning and Maintenance Inspecting BurnerTroubleshooting Observed Problem Possible Cause RemedyNatural GAS Heater Gas leak. See Warning statement Illustrated Parts List VN10TAParts List KEY Part Number Description QTYSpecifications Technical Service Servicepublications Replacement PartsService Hints Accessory104086 Warranty Information

VN10TA specifications

Desa VN10TA is an advanced multi-functional agricultural tractor designed for a wide range of farming tasks. This powerful machine is engineered to meet the needs of modern agriculture, combining efficiency, durability, and versatility into one cohesive package.

One of the standout features of the Desa VN10TA is its robust engine. Equipped with a high-performance diesel engine, it delivers impressive horsepower while ensuring fuel efficiency. The engine is designed with advanced fuel injection technology, optimizing power output and reducing emissions, making it compliant with current environmental standards. This results in lower operating costs for farmers without compromising performance.

The VN10TA also comes with a hydrostatic transmission system, allowing for smoother operation and easier handling. This system provides seamless speed adjustments and enhances maneuverability, particularly in tight spaces. Operators can easily navigate through various terrains, whether working on flat fields or uneven landscapes. The intuitive controls make it user-friendly, ensuring that even those with limited experience can operate it effectively.

In terms of build quality, the Desa VN10TA is constructed with durable materials, ensuring longevity even under harsh working conditions. The chassis is designed to withstand rigorous use while providing stability and balance. This makes it ideal for both heavy-duty tasks and lighter agricultural activities.

Another significant characteristic of the VN10TA is its adaptability to various attachments and implements. The tractor can be equipped with a variety of tools, ranging from plows and harrows to seeders and trailers. This versatility allows farmers to customize their machines based on specific needs, optimizing productivity throughout the growing season.

Incorporating cutting-edge technology, the Desa VN10TA is equipped with an advanced monitoring system. This system provides real-time data regarding engine performance, fuel consumption, and maintenance needs, allowing for proactive management of the tractor. Additionally, the model features ergonomic seating and a spacious cabin, enhancing operator comfort during long hours of work.

Overall, the Desa VN10TA is a reliable and efficient solution for modern agricultural challenges. Its powerful engine, advanced transmission, build quality, and versatility make it an asset to any farming operation, helping to improve productivity and reduce labor costs in the field. Whether for small farms or larger agricultural enterprises, the VN10TA is positioned to meet the evolving demands of the industry.
Top Page Image Contents