Desa VN10TA Lighting Instructions, Thermostat Control Operation, To Turn OFF GAS To Appliance

Page 11
C-clockwise

OWNER’S MANUAL

OPERATING

HEATER

Continued

LIGHTING

INSTRUCTIONS

1.STOP! Read the safety information on page 10, column 3.

2.Make sure equipment shutoff valve is fully open.

3. Turn control knob clockwise Clockwise to the OFF position.

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol- low “B” in the safety information on page 10, column 3. If you don’t smell gas, go to the next step.

5.Press in control knob, and turn coun-

terclockwise to pilot position. Keep control knob pressed for five seconds.

Note: You may be running this heater for the first time after hook- ing up to gas supply. If so, the con- trol knob may need to be pressed in for 30 seconds. This will allow air to bleed from the gas system.

Ignitor Button

Control Knob

 

PILOT

LO

 

OFF

 

 

HI

 

IGNITOR

Figure 15 - Control Knob In The OFF Position

6.With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the bottom of burner. The pilot can be seen below the left hand plaque. If needed, keep pressing ignitor but- ton until pilot lights.

•If pilot does not stay lit, contact a qualified service person or gas supplier for repairs.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot does not light, repeat steps 3 through 7. This heater has a safety interlock system. Wait one

(1)minute before lighting pilot again.

8.Turn control knob counterclockwise

C-clockwiseto desired heating level. Both plaques should light. Set control

knob to any heat level between HI and LO.

Ignitor Electrode

Thermocouple

Pilot Burner

Figure 16 - Pilot

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

THERMOSTAT

CONTROL

OPERATION

The control knob can be set to any heat level between HI and LO. When the room temperature exceeds the set temperature, the burner will cycle to pilot. The burner will cycle back on when room tempera- ture drops below the set temperature. Selecting a higher setting will cause the heater to run longer, producing greater heat output. At lower settings, the heater will run less.

Note: The thermostat sensing bulb mea- sures the temperature of air near the heater cabinet. This may not always agree with room temperature (depending on housing construction, installation loca- tion, room size, open air temperatures, etc.) Frequent use of your heater will let you determine your own comfort levels.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise Clockwise to the OFF position.

Shutting Off Burner Only (pilot stays lit)

Turn control knob clockwise Clockwise to the PILOT position.

MANUAL LIGHTING

PROCEDURE

1.Remove front panel (see Figure 10, page 8).

2.Follow steps 1 through 5 under Light- ing Instructions.

3.With control knob pressed in, strike match. Hold match to pilot until pi- lot lights.

4.Keep control knob pressed in for 10 seconds after pilot is lit. After 10 sec- onds, release control knob. Follow step 8 under Lighting Instructions.

5.Replace front panel.

104086

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualNatural GAS Heater Safety InformationUnpacking Product FeaturesProduct Identification Local CodesConfined and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Locating Heater InstallationInstallation Items Installing Heater to WallRemoving Front Panel Of Heater Installing Two Mounting ScrewsInstalling Bottom Mounting Screw Placing Heater On Mounting ScrewsGas Connection Connecting to GAS SupplyOperating Heater For Your Safety Read Before LightingPressure Testing Gas Supply Piping System Pressure Testing Heater Gas ConnectionsTo Turn OFF GAS To Appliance Manual Lighting ProcedureLighting Instructions Thermostat Control OperationInspecting Burner Cleaning and MaintenanceObserved Problem Possible Cause Remedy TroubleshootingNatural GAS Heater Gas leak. See Warning statement VN10TA Illustrated Parts ListKEY Part Number Description QTY Parts ListAccessory SpecificationsTechnical Service Servicepublications Replacement Parts Service Hints104086 Warranty Information

VN10TA specifications

Desa VN10TA is an advanced multi-functional agricultural tractor designed for a wide range of farming tasks. This powerful machine is engineered to meet the needs of modern agriculture, combining efficiency, durability, and versatility into one cohesive package.

One of the standout features of the Desa VN10TA is its robust engine. Equipped with a high-performance diesel engine, it delivers impressive horsepower while ensuring fuel efficiency. The engine is designed with advanced fuel injection technology, optimizing power output and reducing emissions, making it compliant with current environmental standards. This results in lower operating costs for farmers without compromising performance.

The VN10TA also comes with a hydrostatic transmission system, allowing for smoother operation and easier handling. This system provides seamless speed adjustments and enhances maneuverability, particularly in tight spaces. Operators can easily navigate through various terrains, whether working on flat fields or uneven landscapes. The intuitive controls make it user-friendly, ensuring that even those with limited experience can operate it effectively.

In terms of build quality, the Desa VN10TA is constructed with durable materials, ensuring longevity even under harsh working conditions. The chassis is designed to withstand rigorous use while providing stability and balance. This makes it ideal for both heavy-duty tasks and lighter agricultural activities.

Another significant characteristic of the VN10TA is its adaptability to various attachments and implements. The tractor can be equipped with a variety of tools, ranging from plows and harrows to seeders and trailers. This versatility allows farmers to customize their machines based on specific needs, optimizing productivity throughout the growing season.

Incorporating cutting-edge technology, the Desa VN10TA is equipped with an advanced monitoring system. This system provides real-time data regarding engine performance, fuel consumption, and maintenance needs, allowing for proactive management of the tractor. Additionally, the model features ergonomic seating and a spacious cabin, enhancing operator comfort during long hours of work.

Overall, the Desa VN10TA is a reliable and efficient solution for modern agricultural challenges. Its powerful engine, advanced transmission, build quality, and versatility make it an asset to any farming operation, helping to improve productivity and reduce labor costs in the field. Whether for small farms or larger agricultural enterprises, the VN10TA is positioned to meet the evolving demands of the industry.
Top Page Image Contents