Desa VN10TA installation manual Connecting to GAS Supply, Gas Connection

Page 9

OWNER’S MANUAL

INSTALLATION

Continued

CONNECTING TO GAS SUPPLY

WARNING: This appliance re- quires a 3/8" NPT (National Pipe Thread) inlet connection to the pressure regulator.

WARNING: A qualified service person must connect heater to gas supply. Follow all local codes.

Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.

CAUTION: Use pipe joint seal- ant that is resistant to liquid pe- troleum (LP) gas.

Install sediment trap in supply line as shown in Figure 12. Locate sediment trap where it is within reach for cleaning. Locate sedi- ment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

IMPORTANT: Hold pressure regulator with wrench when connecting it to gas pip- ing and/or fittings.

WARNING: Never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas.

IMPORTANT: Check gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 14 inches of water. If gas line pressure is higher, heater regulator damage could occur.

CAUTION: Use only new, black iron or steel pipe. Inter- nally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe 3/8" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of pressure will occur

Installation must include a equipment shutoff valve, ground joint union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be up- stream from heater (see Figure 12). An

3/8" NPT Pipe Nipple

Equipment

Shutoff

Valve *

From

Gas Meter (5" W.C. to 10.5" W.C. Pressure)

3" Minimum

Figure 12 - Gas Connection

Pressure

Regulator

Heater

Cabinet

Ground Joint

Union

Tee Joint

 

 

 

 

 

 

 

 

Reducer

 

Test

Bushing to

 

Gauge

1/8" NPT

 

Connection *

1/8" NPT

 

 

Plug Tap

 

 

 

 

 

 

Tee

 

 

 

Joint

 

 

Pipe

 

Sediment

 

Trap

Nipple

 

 

 

Cap

 

 

 

appliance main gas valve (equipment shutoff valve) shall be provided in an accessible location for turning on or shutting off the gas to the appliance.

IMPORTANT: Install an equipment shutoff valve in an accessible location. The equip- ment shutoff valve is for turning on or shutting off the gas to the appliance.

*A CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA/AGA design-certified equipment shutoff valve from your dealer. See Accessory, page 18.

Continued

104086

9

Image 9
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualNatural GAS Heater Safety InformationProduct Identification Product FeaturesLocal Codes UnpackingProviding Adequate Ventilation AIR for Combustion and VentilationUnusually Tight Construction Confined and Unconfined SpaceAIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Items InstallationInstalling Heater to Wall Locating HeaterInstalling Bottom Mounting Screw Installing Two Mounting ScrewsPlacing Heater On Mounting Screws Removing Front Panel Of HeaterGas Connection Connecting to GAS SupplyPressure Testing Gas Supply Piping System For Your Safety Read Before LightingPressure Testing Heater Gas Connections Operating HeaterLighting Instructions Manual Lighting ProcedureThermostat Control Operation To Turn OFF GAS To ApplianceInspecting Burner Cleaning and MaintenanceObserved Problem Possible Cause Remedy TroubleshootingNatural GAS Heater Gas leak. See Warning statement VN10TA Illustrated Parts ListKEY Part Number Description QTY Parts ListTechnical Service Servicepublications Replacement Parts SpecificationsService Hints Accessory104086 Warranty Information

VN10TA specifications

Desa VN10TA is an advanced multi-functional agricultural tractor designed for a wide range of farming tasks. This powerful machine is engineered to meet the needs of modern agriculture, combining efficiency, durability, and versatility into one cohesive package.

One of the standout features of the Desa VN10TA is its robust engine. Equipped with a high-performance diesel engine, it delivers impressive horsepower while ensuring fuel efficiency. The engine is designed with advanced fuel injection technology, optimizing power output and reducing emissions, making it compliant with current environmental standards. This results in lower operating costs for farmers without compromising performance.

The VN10TA also comes with a hydrostatic transmission system, allowing for smoother operation and easier handling. This system provides seamless speed adjustments and enhances maneuverability, particularly in tight spaces. Operators can easily navigate through various terrains, whether working on flat fields or uneven landscapes. The intuitive controls make it user-friendly, ensuring that even those with limited experience can operate it effectively.

In terms of build quality, the Desa VN10TA is constructed with durable materials, ensuring longevity even under harsh working conditions. The chassis is designed to withstand rigorous use while providing stability and balance. This makes it ideal for both heavy-duty tasks and lighter agricultural activities.

Another significant characteristic of the VN10TA is its adaptability to various attachments and implements. The tractor can be equipped with a variety of tools, ranging from plows and harrows to seeders and trailers. This versatility allows farmers to customize their machines based on specific needs, optimizing productivity throughout the growing season.

Incorporating cutting-edge technology, the Desa VN10TA is equipped with an advanced monitoring system. This system provides real-time data regarding engine performance, fuel consumption, and maintenance needs, allowing for proactive management of the tractor. Additionally, the model features ergonomic seating and a spacious cabin, enhancing operator comfort during long hours of work.

Overall, the Desa VN10TA is a reliable and efficient solution for modern agricultural challenges. Its powerful engine, advanced transmission, build quality, and versatility make it an asset to any farming operation, helping to improve productivity and reduce labor costs in the field. Whether for small farms or larger agricultural enterprises, the VN10TA is positioned to meet the evolving demands of the industry.