Dimplex WB3, WB7, WB15, WB5E 1 Overflow Pipe Rear Entry, Vent Pipe, FIT Case, WB5E ONLY. FIT TAP

Page 6

OVERFLOW PIPE REAR ENTRY

In your fitting kit you will find a straight push on connector with a small length of 15mm copper tube pushed into it.

If rear entry has been chosen this connector must be replaced by a push on elbow (available from plumber’s merchants). Push the elbow onto the overflow pipe on the bracket (alongside the solenoid).

The pipe must have a continuous fall and should not be longer than 200mm (if a longer run is required use 22mm pipe to avoid airlocks). The overflow pipe should have no more than four right angle bends and should discharge to a safe visible position.

Under certain conditions, the overflow pipe could vent steam, hot water or cold water and the manufacturers cannot be held responsible should damage arise from such discharge if the overflow pipe has not been directed to a suitable position where overflowing water can run away safely.

Under no circumstances should the overflow pipe be allowed to vent inside the case of the boiler.

VENT PIPE

A small silicone tube connects the boiler to the wall bracket. Ensure that this is connected and that the opening in the bracket is not obstructed.

FIT CASE

Attach the L.E.D display lead to the case per the instructions. Using the fixing screws fit the outer case to the boiler.

WB5E ONLY. FIT TAP

Remove plastic plug from the tap boss. Ensure that the yellow washer is in place and carefully screw the chromed tap extension into place using a 28mm open-ended spanner to tighten. Do not use grips or tools that are likely to scratch the chrome.

Push the grey tap collar firmly into place and twist to fit snugly against the case.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents AUTO-FILL Water Boilers Important Health and Safety Information Check List Installation Positioning the UnitIntroduction Electrical Connection ALL MachinesRear Entry of Cable Bottom Entry of CableWater Connection Bottom Entry Rear EntryOverflow Pipe Bottom Entry FIT Case Overflow Pipe Rear EntryVent Pipe WB5E ONLY. FIT TAPOperation All models except WB5E Temperature Control & Safety CUT OUT CleaningOperation WB5Eonly Technical Specification ALL Models MaintenanceDE-SCALING All models except WB5E DE-SCALING WB5EService Warning Light WB5E only Service Warning Light All Models except WB5E Constant

WB7, WB5E 1, WB3, WB15 specifications

The Dimplex WB series, including models WB5E, WB15, WB3, and WB7, represents an innovative and versatile range of electric heating solutions designed specifically for residential and commercial environments. With a combination of efficient heating technology and user-friendly features, these electric heaters provide effective warmth while maintaining aesthetic appeal.

The Dimplex WB5E is a compact unit that offers exceptional efficiency and low energy consumption. It features a built-in digital thermostat, allowing users to maintain the desired room temperature with precision. Moreover, it incorporates advanced convection heating technology, which circulates warm air effectively throughout the space, ensuring even warmth and comfort.

The WB15 model offers a higher output, making it suitable for larger rooms or commercial spaces. Its sleek design allows for wall mounting, preserving floor space while delivering powerful heating capabilities. This model also includes an adjustable thermostat and a timer function, enabling users to customize their heating schedule to maximize energy savings.

For those needing a more compact solution, the Dimplex WB3 is an ideal choice. This model is perfect for smaller rooms or areas where space is at a premium. Despite its size, the WB3 does not compromise on performance, utilizing rapid warm-up technology to quickly raise the ambient temperature. Additionally, the unit is equipped with safety features such as overheat protection and a tip-over switch, ensuring peace of mind for users.

The WB7 model strikes a balance between size and heating output, making it an excellent choice for medium-sized spaces. It comes with integrated fan assistance that enhances heat distribution, resulting in a comfortable atmosphere even in larger areas. The WB7 includes an easy-to-read LCD display for effortless temperature adjustments and a user-friendly control panel that offers various operational modes, such as eco and comfort settings.

All models in the Dimplex WB series are designed with energy efficiency in mind, using technologies that reduce energy waste while providing reliable heat. Their contemporary aesthetic fits seamlessly into modern interiors, and the choice of finish options allows users to select a look that complements their decor. Overall, the Dimplex WB series represents a blend of functionality, safety, and style, catering to diverse heating requirements.
Top Page Image Contents