Dimplex WB7, WB15, WB3, WB5E 1 Operation WB5Eonly, Temperature Control & Safety CUT OUT, Cleaning

Page 8

OPERATION (WB5Eonly)

After the electrical and water connections have been made, switch the power and water supply on.

When the power supply is switched on, the small indicator lamp on the front panel will glow orange. This means that the water is filling to the bottom probe. When the bottom probe has been reached, the indicator lamp will change to red to show heating. When the water has reached the correct temperature the light will change green. Wait a further 10 minutes before starting to use.

Your machine does not fill completely at once. The water input is electronically controlled to obtain maximum output, temperature and efficiency.

In daily use, switch on and wait for the green light. The water will then be at the correct temperature and the boiler ready to use.

TEMPERATURE CONTROL & SAFETY CUT OUT

A small knob protrudes from the base of the mounting bracket (Not WB5E). This controls the boiler temperature. It has been factory set at approximately 98oC and should not need adjustment. However, under certain conditions (extreme change in ambient room or cold water temperature), the boiler temperature may fluctuate slightly. The knob may then be used to adjust this. Using a screwdriver, loosen the transit bracket, which holds the knob in place. Turn the knob clockwise to increase or anti-clockwise to decrease the temperature.

All models except WB5E

Should the temperature be set too high, steam or boiling water will discharge through the overflow pipe. In the event of this happening, a high temperature control switch will switch off the heater. The red service light will flash 10 or 12 times depending upon the water level. Switch the boiler off at the electricity supply and switch back on a few moments later. This will reset the boiler but if it cuts out again it is recommended that you then adjust the temperature by turning the knob anti-clockwise. If the boiler continues to over-boil, contact the Instanta service department on 01704 502911 for advice.

WB5E

Should the temperature be set too high, steam or boiling water will discharge through the overflow pipe. In the event of this happening, a high temperature control switch will switch off the heater. After a short period, the neon indicator will change from green to flashing red or flashing red and green. Switch the boiler off at the electricity supply and switch back on a few moments later. This will reset the boiler but if it cuts out again it is recommended that you contact the Instanta service department for advice.

CLEANING

The external surface of the machine can be kept clean by wiping with a damp cloth.

Do not use abrasive material on the outer surface of the machine.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents AUTO-FILL Water Boilers Important Health and Safety Information Installation Positioning the Unit IntroductionCheck List Electrical Connection ALL MachinesWater Connection Rear Entry of CableBottom Entry of Cable Overflow Pipe Bottom Entry Bottom EntryRear Entry Overflow Pipe Rear Entry Vent PipeFIT Case WB5E ONLY. FIT TAPOperation All models except WB5E Operation WB5Eonly Temperature Control & Safety CUT OUTCleaning Technical Specification ALL Models MaintenanceDE-SCALING All models except WB5E DE-SCALING WB5EService Warning Light WB5E only Service Warning Light All Models except WB5E Constant

WB7, WB5E 1, WB3, WB15 specifications

The Dimplex WB series, including models WB5E, WB15, WB3, and WB7, represents an innovative and versatile range of electric heating solutions designed specifically for residential and commercial environments. With a combination of efficient heating technology and user-friendly features, these electric heaters provide effective warmth while maintaining aesthetic appeal.

The Dimplex WB5E is a compact unit that offers exceptional efficiency and low energy consumption. It features a built-in digital thermostat, allowing users to maintain the desired room temperature with precision. Moreover, it incorporates advanced convection heating technology, which circulates warm air effectively throughout the space, ensuring even warmth and comfort.

The WB15 model offers a higher output, making it suitable for larger rooms or commercial spaces. Its sleek design allows for wall mounting, preserving floor space while delivering powerful heating capabilities. This model also includes an adjustable thermostat and a timer function, enabling users to customize their heating schedule to maximize energy savings.

For those needing a more compact solution, the Dimplex WB3 is an ideal choice. This model is perfect for smaller rooms or areas where space is at a premium. Despite its size, the WB3 does not compromise on performance, utilizing rapid warm-up technology to quickly raise the ambient temperature. Additionally, the unit is equipped with safety features such as overheat protection and a tip-over switch, ensuring peace of mind for users.

The WB7 model strikes a balance between size and heating output, making it an excellent choice for medium-sized spaces. It comes with integrated fan assistance that enhances heat distribution, resulting in a comfortable atmosphere even in larger areas. The WB7 includes an easy-to-read LCD display for effortless temperature adjustments and a user-friendly control panel that offers various operational modes, such as eco and comfort settings.

All models in the Dimplex WB series are designed with energy efficiency in mind, using technologies that reduce energy waste while providing reliable heat. Their contemporary aesthetic fits seamlessly into modern interiors, and the choice of finish options allows users to select a look that complements their decor. Overall, the Dimplex WB series represents a blend of functionality, safety, and style, catering to diverse heating requirements.
Top Page Image Contents