Desa CBT30NT, CBT30PT Installing Heater to Wall, Mounting Bracket, Removing Front Panel Of Heater

Page 9

INSTALLATION

Continued

INSTALLING HEATER TO WALL

Mounting Bracket

Locate mounting bracket in heater carton. Remove mounting bracket from heater carton.

Figure 6 - Mounting Bracket

Removing Front Panel Of Heater

1.Remove the four painted screws, two on each side of front panel.

2.Pull bottom of front panel forward, then out.

3.Remove any remaining packaging materials.

Screw

Front Panel

Figure 7 - Removing Front Panel Of Heater

Methods For Attaching Mounting Bracket To Wall Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes are 14" (35.6 cm) apart from their centers. Attach mount- ing bracket to wall in one of two ways:

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain mini- mum clearances shown in Figure 8. If you can, provide greater clearances from floor and joining wall.

2.Mark screw locations on wall (see Figure 8).

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

 

8"

14" (35.6 cm)

 

 

 

(20.3

 

 

 

 

cm)

 

 

 

AdjoiningallW

Min.

 

 

 

Only Insert Mounting

 

18 3/4"

Screws Through Last

 

(47.6 cm

 

 

Hole On Each End

 

Min.

 

 

Floor

 

 

 

20,000 Btu/hr Models

 

 

12"

14" (35.6 cm)

 

 

 

(30.4

 

 

 

 

cm)

 

 

 

AdjoiningallW

Min.

 

 

 

Only Insert Mounting

 

18 3/4"

Screws Through Last

 

(47.6 cm)

 

 

 

Hole On Each End

 

 

 

Min.

 

 

 

 

 

 

Floor

 

 

 

30,000 Btu/hr Models

 

Figure 8 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws and spacers

are in hardware package. The hardware package

is provided with heater.

 

 

107882-01M

www.desatech.com

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS Table of Contents Safety Information Safety Device Product FeaturesLocal Codes Ignition SystemProviding Adequate Ventilation AIR for Combustion VentilationFollowing are excerpts from National Fuel Unusually Tight ConstructionVentilation AIR Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside BuildingInstallation Items AIR for Combustion Ventilation InstallationCheck GAS Type Ventilation Air From OutdoorsThermostat Sensing Bulb Locating HeaterMounting Bracket Installing Heater to WallRemoving Front Panel Of Heater Marking Screw LocationsAttaching To Wall Stud Method Installing Bottom Mounting ScrewsAttaching To Wall Anchor Method Placing Heater On Mounting BracketMounting Base Feet to Floor Where required by local code Connecting to GAS SupplyMounting Heater to Floor Optional Mounting Base Feet to HeaterBe upstream from heater see Figure Dealer. See Accessories,Appliance Apply pipe joint sealant lightly to male NPT Clogged heater valvesChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa For Your Safety Read Before Lighting Operating HeaterLighting Instructions Inspecting Heater Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationBurner Flame Pattern Soft bristled brush to cleanODS/PILOT and Burner Burner Pilot AIR InletService Hints Cleaning MaintenanceTechnical Service When Gas Pressure Is Too LowObserved Problem Possible Cause Remedy TroubleshootingControl knob is not in pilot position Contact local propane/LP gas companyProblem could be caused by Goes out when control knob is Control knob not pressedAssembly Delayed ignition of burners Manifold pressure is too lowWhen heated, vapors from Turn heater off when using Noise when burner is litSlight smoke or odor during Initial operation Processes Hours of operationGas leak. See Warning Specifications Service Publications Replacement PartsIllustrated Parts Breakdown Parts List 111435-01 Electronic Ignitor 097159-04 Piezo IgnitorFront Panel 107954-01 107955-01 Equipment Shutoff Valve GA5010 AccessoriesFAN Kits GA3250T Floor Mounting KIT GA4550Parts Central Keep this Warranty Warranty Information

CBT30NT, CBT30PT specifications

The Desa CBT30NT and CBT30PT are high-performance heating solutions designed to deliver efficient warmth for both residential and commercial applications. These units are known for their reliability, innovative features, and easy integration into various spaces. They are particularly suited for those seeking effective heating options without compromising on energy efficiency.

The CBT30NT, or the natural gas version, stands out with its ability to provide consistent warmth through a direct vent system. This allows for safe operation while minimizing the impact on indoor air quality. It effectively draws combustion air from outside, which is essential for spaces with limited ventilation. The CBT30PT, on the other hand, is a propane variant, providing flexibility for users who may not have access to natural gas lines. Both models are designed with user convenience in mind, featuring a simple control system that allows for easy adjustments and temperature settings.

One of the key characteristics of these heaters is their advanced thermostat control, which enables precise temperature management. This feature ensures energy usage is optimized, preventing unnecessary heating and reducing utility costs. The compact and sleek design of the CBT30NT and CBT30PT allows them to fit seamlessly into any room without being an eyesore.

The heaters are equipped with durable materials, providing resilience against the rigors of daily use. They feature safety mechanisms, including flame failure safety devices, ensuring peace of mind for users. Furthermore, both models incorporate a forced air design, which disperses heat efficiently throughout the space, eliminating cold spots and creating a more uniform climate.

In summary, the Desa CBT30NT and CBT30PT are ideal heating solutions that combine safety, efficiency, and aesthetic appeal. Their natural gas and propane options respectively cater to a diverse range of user needs, making them versatile choices for enhanced comfort. With their advanced technology and user-friendly features, these heaters are a worthy investment for anyone in need of reliable heating solutions. Emphasizing energy efficiency and user safety, they represent the next generation of residential and commercial heating systems.
Top Page Image Contents