A.O. Smith Complete Installation Guide for the XDVS Water Heater
Page 11

16.Go back indoors to attach inside collar to the inside wall. Place the collar against the wall. Secure to wall by using 4 long sheet metal screws.

FIGURE 30

NOTE: Screws are supplied; however, substitution may be necessary depending on the interior wall material.

17.Using the tube of sealant supplied, run an ample amount of sealant around the edge of the vent pipe where it is inserted through the inside collar to seal air drafts from wall.

FIGURE 31

OPTIONAL VERTICAL VENT KIT # 900124-6 WITH STANDARD HORIZONTAL VENT KIT INSTALLATION #2

Use the simple equation below, chart and drawing to find the length of expansion of the telescoping flue sections. Because of manufacturing tolerances, place the telescoping extension on the water heater and adjust the height (“X” Dimension) and mark the point. Once the length has been determined, lock the two sections together by drilling two holes (180° apart) in the pipe and securing with the screws supplied.

EQUATION: C - A -10” = X

 

*GALLON

*BTU’s in 1000’s

 

 

CAPACITY

NAT/L.P.

A

40

36/36

48-3/4

 

50

38/38

57-1/2

40

40/40

48-3/4

 

50

48/44

61

 

75

55 NAT.

63

*See models and rating plate attached to the water heater for specific model number and other detailed information.

ANY OPTIONAL VENT KIT

FIGURE 32

The opening through the wall should be cut at this time. If it hasn’t been, refer back to that section.

1.First it must be determined how far the vertical (3” dia.) telescoping flue sections are set and locked together using the two screws supplied as shown below.

FIGURE 33

FIGURE 34

NOTE: EACH PART HAS BEEN STAMPED WITH A PART NUMBER.

2.Set the vertical (3” diameter) telescoping flue section in place on the flue collar. Using a #22 drill bit, drill two holes (180° apart) and secure the vertical assembly to the flue collar.

FIGURE 35

3.Slide the 6” vent telescoping section apart to reveal the beads. Using the caulking supplied, fill the beads.

FIGURE 36

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Direct Vent GAS Models Replacement Parts Typical InstallationExtended NON-USE Periods Vent KIT Assembly ComponentsExternal Damage Chemical Vapor CorrosionGAS Connections Water Potable Heating and Space HeatingClosed Water System Vent Pipe Termination Relief ValveVenting Venting Clearances Optional Wire GrillCombustion AIR and Ventilation Possible Extension Combinations Flue ExtensionsCutting the Opening Through Outside Wall ALL InstallationsVertical Extension KIT Height Horizontal Extension KITWater Heater Attitude Standard Vent KIT Installation #1Page Gallon Equation C a -10 =Page Page Optional Horizontal Vent KIT #900124-7 Installation #3 Page Capacity Natural Equation C a 10 =Insert the 6 telescoping vent section into the wall Page Filling High Altitude InstallationsTemperature Regulation Valve and Pipe InsulationForce For Your Safety Read Before LightingDraining Temperature & Pressure Relief ValvePilot and Main Burner Cathodic Protection Anode Anode ROD MaintenanceCondensation Troubleshooting Limitation on Implied Warranties Service and Labor ResponsibilityClaim Procedure Conditions and ExceptionsPage Page Page Tennessee Waltz PARKWAY, Ashland CITY, TN

GDVH, XDVS, GDVS specifications

A.O. Smith is a leading manufacturer of water heating solutions, renowned for offering innovative products that cater to both residential and commercial needs. Among its impressive lineup, the GDVH, XDVS, and GDVS models stand out, showcasing advanced features and technologies that enhance performance and efficiency.

The A.O. Smith GDVH series is designed for high-efficiency gas water heating. These units come equipped with the latest condensing technology, which allows them to utilize heat that would otherwise be lost in traditional systems. This process results in improved energy efficiency and significant cost savings on energy bills. The GDVH series is also noted for its EcoSmart feature, which adjusts the operational settings according to water usage patterns, further optimizing energy consumption.

The XDVS model, on the other hand, is a testament to A.O. Smith's commitment to durability and performance. Constructed with high-quality materials, the XDVS offers exceptional resistance against corrosion, thereby prolonging the lifespan of the unit. This model features advanced controls that provide real-time diagnostic information, enabling users to monitor performance and schedule maintenance effectively.

The GDVS series bridges the gap between affordability and performance. These water heaters are designed with a user-friendly interface, allowing for simple operation and easy adjustments. The GDVS models utilize a high-efficiency burner system that ensures rapid heating capabilities while keeping energy costs down. Additionally, the units are compact, making them ideal for homes with limited installation space, without compromising on output performance.

All three models incorporate A.O. Smith’s proven heating technologies that prioritize safety and efficiency. They feature advanced flame sensors and integrated safety controls that protect against overheating and ensure reliable operation. Furthermore, these models are compatible with various installation configurations, making them versatile options for diverse applications.

In conclusion, A.O. Smith's GDVH, XDVS, and GDVS water heaters present a blend of cutting-edge technology, rugged durability, and user-friendly features, catering to the needs of modern households and businesses. With energy efficiency as a hallmark of their design, these models not only promise excellent performance but also contribute to sustainable energy usage, making them an ideal choice for eco-conscious consumers.
Top Page Image Contents