Temperature Regulation, Checking Venting, D E F

TEMPERATURE REGULATION

DANGER

THIS WATER HEATER IS EQUIPPED WITH AN ADJUSTABLE THERMOSTAT TO CONTROL WATER TEMPERATURE. HOT WATER TEMPERATURES REQUIRED FOR AUTOMATIC DISHWASHING AND LAUNDRY USE CAN CAUSE PAINFUL SCALDING WITH POSSIBLE SERIOUSAND PERMANENT INJURY. THE TEMPERATUREAT WHICH INJURY OCCURS VARIES WITH THE PERSON’S AGE AND THE TIME OF THE EXPOSURE. THE SLOWER RESPONSE TIME OF CHILDREN, AGED OR DISABLED PERSONS INCREASES THE HAZARDS TO THEM. NEVER ALLOW SMALL CHILDREN TO USE A HOT WATER TAP, OR TO DRAW THEIR OWN BATH WATER. NEVER LEAVE A CHILD OR DISABLED PERSON UNATTENDED IN A BATHTUB OR SHOWER.

THE WATER HEATER SHOULD BE LOCATED IN AN AREA WHERE THE GENERAL PUBLIC DOES NOT HAVE ACCESS. IF A SUITABLE AREA IS NOT AVAILABLE, A COVER SHOULD BE INSTALLED OVER THE THERMOSTAT TO PREVENT TAMPERING. Suitable covers are available through A.O. Smith Water Products Company, 5621 W. 115th Street, Alsip, IL 60803. In Canada, A.O. Smith Enterprises, LTD., P.O. Box 310- 768 Erie Street, Stratford, Ontario N5A 6T3.

It is recommended that lower water temperatures be used to avoid the risk of scalding. It is further recommended, in all cases, that the water temperature setting be set for the lowest temperature that satisfies your hot water needs. This will also provide the most energy efficient operation of the water heater. The water temperature adjustment was factory set at the lowest temperature. Pressing the "COOLER" button decreases

temperature and pressing the "HOTTER" button increases the temperature.

		Display	Time to Produce
		Display	2nd & 3rd Degree
	Temperature Setting	B C D E F	Burns on Adult Skin
F	= approx. 180°F (82°C)		Nearly instantaneous
D	= approx. 160°F (71°C)		About 1/2 seconds
B	= approx. 140°F (60°C)		Less than 5 seconds
	= approx. 120°F (49°C)		More than 5 minutes

FIGURE 6

SETTINGTHE WATER HEATERTEMPERATUREAT120°F (49°C) (APPROX.

"" MARK ON FACE OF THE TEMPERATURE ADJUSTING DIAL) WILL REDUCE THE RISK OF SCALDS. Some states require settings at specific lower temperatures.

Temperature	Time to Produce 2nd & 3rd
Setting	Degree Burns on Adult Skin
180°F (82°C)	Nearly instantaneous
170°F (77°C)	Nearly instantaneous
160°F (71°C)	About 1/2 second
150°F (66°C)	About 1-1/2 second
140°F (60°C)	Less than 5 seconds
130°F (54°C)	About 30 seconds
120°F (49°C)	More than 5 minutes

Figure 6 shows the approximate water temperatures produced at various thermostat settings. Short repeated heating cycles caused by small hot water uses can cause temperatures at the point of use to exceed the thermostat setting by up to 20°F (11°C). If you experience this type of use you should consider using lower temperature settings to reduce scald hazards.

Valves for reducing point of use temperature by mixing cold and hot water are available. Also available are inexpensive devices that attach to faucets to limit hot water temperatures. Contact a licensed plumber or the local plumbing authority.

To avoid any unintentional changes in water temperature settings, the control has a tamper resistant feature for changing the temperature setting. To change the temperature setting follow these instructions:

1."Wake Up" the temperature indicators by holding down both the "COOLER" and "HOTTER" temperature adjustment buttons at the same time for one second (see Figure 6). One or two of the temperature indicators will light up. These indicators will only remain on for 30 seconds if no further buttons are pressed. After 30 seconds the control will go back to "Sleep" mode.

2.Release both of the temperature adjustment buttons.

A.To decrease the temperature press and release the "COOLER" button until desired setting is reached.

B.To increase the temperature press and release the "HOTTER" button until the desired setting is reached.

NOTE: Holding down the button will not continue to lower or raise the temperature setting. The button must be pressed and released for each temperature change desired.

SHOULD OVERHEATING OCCUR OR THE GAS SUPPLY FAIL TO SHUT OFF, TURN OFF THE MAIN MANUAL GAS SHUTOFF VALVE TO THE APPLIANCE. SEE FIGURE 1 (G).

CHECKING VENTING

The following steps shall be followed with each appliance connected to the venting system placed in operation, while any other appliances connected to the venting system are not in operation.

1.Seal any unused openings in the venting system.

2.Inspect the venting system for proper size and horizontal pitch, as required in the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or the CAN/CGA B149 Installation codes and these instructions. Determine that there is no blockage or restriction, leakage, corrosion and other deficiencies which could cause an unsafe condition.

3.So far as is practical, close all building doors and windows and all doors between the space in which the water heater(s) connected to the venting system are located and other spaces of the building. Turn on all appliances not connected to the venting system. Turn on all exhaust fans, such as range hoods and bathroom exhausts, so they shall operate at maximum speed. Close fireplace dampers.

4.Follow the lighting instruction. Place the water heater being inspected in operation. Adjust thermostat so appliance shall operate continuously.

5.Test for vent system leakage after 5 minutes of main burner operation.

BTI-80 specifications

The A.O. Smith BTI-80 is a notable contender in the residential water heater market, renowned for its reliable performance, energy efficiency, and innovative features. Designed with the modern homeowner in mind, this model stands out due to its ability to provide ample hot water while minimizing energy consumption, making it an excellent choice for a variety of home sizes and needs.

At its core, the BTI-80 is a 80-gallon capacity tank water heater, catering to households with higher hot water demand. This large capacity ensures that families can comfortably enjoy long showers, run multiple appliances simultaneously, and meet their everyday hot water requirements without experiencing a dip in temperature. The tank's size makes it particularly suitable for larger families or homes with multiple bathrooms.

One of the most significant advancements in the BTI-80 is its state-of-the-art insulation technology. With its high-density foam insulation, this water heater retains heat more effectively, reducing standby heat loss and ensuring that the water remains hot for longer periods. This efficiency translates directly into savings on energy bills, offering an environmentally friendly solution without compromising performance.

The BTI-80 is equipped with a robust and reliable burner system. The gas burner operates efficiently, designed to heat water quickly while still adhering to safety and environmental standards. Additionally, the unit features a self-diagnostic control system that continuously monitors the operational efficiency of the heater. This technology not only contributes to enhanced safety by flagging potential issues but also allows for preventative maintenance, improving the lifespan of the unit.

Another standout characteristic of the A.O. Smith BTI-80 is its user-friendly interface. With accessible temperature controls and easy-to-read indicators, homeowners can easily adjust settings according to their preferences without any hassle.

Moreover, A.O. Smith’s commitment to quality is evident in the warranty that accompanies the BTI-80. The unit is often backed by a generous warranty period, underscoring the company's confidence in its product's durability and performance.

In conclusion, the A.O. Smith BTI-80 is an exceptional water heater that combines capacity, efficiency, and advanced technology. It is designed for homeowners who prioritize both comfort and sustainability, providing a reliable hot water solution that meets the demands of modern living. With its sophisticated features and consumer-friendly design, the BTI-80 is undoubtedly a top choice in the residential market.