Bulldog Security RS82 manual Precautions, Making Wiring Connections

Page 3

Since there are many different makes and models of vehicles, look at the wiring chart on or our website, www.bulldogsecurity.com/wires.htm.

Read this manual thoroughly before starting the installation. You must decide if the parking light option is desired. An optional part #775 will be needed. Please do not skip any steps.

TACH/TACHLESS OPERATION

In most cases the decision to go with tachless mode will save time during the installation. If your vehicle is hard-starting then you should use tach mode.

MAKE SURE YOU PLACE THE WARNING STICKER UNDER YOUR HOOD.

PRECAUTIONS

This system is designed to be used with fuel-injected,

automatic transmission vehicles only.

SAFETY FIRST!

Never start your vehicle if it is indoors, if the keys are in the ignition and you’re sure the car is in park. A periodic safety check is recommended to ensure that your system is in proper working order.

DO NOT use mechanical wiring connections, such as crimp or snap together taps. Follow instructions below.

DO NOT disconnect the battery if the vehicle has an anti-theft-coded radio or is equipped with an airbag. Doing so may cause a warning light to be displayed and may require a trip to the dealer to be corrected.

DO NOT leave the interior or exterior lights on for an extended period of time as it may cause battery drain. Remove the dome light fuse from the fuse box. NOTE: Starter systems do not work well with a partially discharged battery.

DO NOT mount the control module until all connections have been made and tested. Using wire ties or double sided tape, MOUNT THE MODULE UNDER THE DASH. Place the warning sticker under the hood.

WARNING!

GENERAL MOTORS REAR WHEEL DRIVE VEHICLES AND DODGE DAKOTAS

All General Motors rear wheel drive vehicles and Dodge Dakotas built prior to 1996 do not have an electrical Neutral Safety switch. They have a mechanical neutral safety switch. The mechanical neutral safety switch operates as follows.

a)The key will only turn to start position when the gear selector is in park or neutral. b)The key can only be removed from the ignition switch when the gear selector is in the park

position.

You must use special precautions with this system. For more information see page 7.

MAKING WIRING CONNECTIONS

1.Strip back two inches of insulation on the wire from the keyless entry. Two Inches of Bare Wire

2.Strip back one inch of insulation on the wire you need to connect to. One Inch of Bare Wire

3.Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through.

2

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Contents Installation Guide OWNER’S GuideTechnical Assistance System FeaturesSystem Components Required ToolsMaking Wiring Connections PrecautionsMaking END to END Connections Wire TieLocating & Making Connections Ignition Wires +12V in run and crank position onlyAccessory Wires That Power the HEATER/BLOWER Motor STARTER/CRANK Wire +12V only in the start positionBrake Input Factory Alarm Shut Down Wire FasdHood PIN Switch Chassis GroundNeutral Safety Switch Connecting the 11-PIN Harness & 4-RELAY HarnessHOW to USE Your Remote Transmitter Factory ANTI-THEFT SystemsProgramming Instructions

RS82 specifications

The Bulldog Security RS82 represents a cutting-edge advancement in vehicle security systems, tailored to provide top-tier protection for vehicles of various sizes. As theft and vandalism become more sophisticated, the RS82 offers a robust solution designed to keep your vehicle secure while offering convenience and user-friendly features.

One of the standout characteristics of the Bulldog Security RS82 is its powerful immobilizer function. This feature works by disabling critical engine components, rendering the vehicle almost impossible to start without the authorized key or remote. Such technology is especially crucial in today's landscape where opportunistic thefts are rampant.

Another notable attribute of the RS82 is its comprehensive alarm system. The alarm includes a loud siren, which effectively deters potential thieves, while also alerting nearby individuals to any unauthorized attempts to access the vehicle. The alarm system is equipped with a range of sensors, including shock sensors that detect vibrations and movements, ensuring that any disturbance triggers an immediate response.

Additionally, the RS82 supports remote control functionality. Users can lock or unlock their vehicle, activate or deactivate the alarm, and even locate their vehicle via GPS all through a compact remote device. This level of control adds convenience, allowing users to manage their vehicle's security from a distance.

In terms of installation, the Bulldog Security RS82 is designed for versatility. Its universal fit allows it to be installed on a variety of vehicle types, including cars, vans, and motorcycles. The system is also engineered for ease of integration, making it suitable for both professional installations and DIY enthusiasts.

Furthermore, the RS82 is built to withstand harsh weather conditions. With a durable casing that protects the internal components from moisture and debris, this security system is reliable regardless of environmental challenges.

In summary, the Bulldog Security RS82 is an exceptional vehicle security solution that combines cutting-edge technologies, including a powerful immobilizer, an effective alarm system, and convenient remote control features. Its robust design and universal fit make it an ideal choice for any vehicle owner looking to enhance security and protect their investment. With the RS82, users can enjoy peace of mind knowing their vehicle is safeguarded against theft and unauthorized access.
Top Page Image Contents