Bulldog Security RS82 Chassis Ground, Brake Input, Antenna, Factory Alarm Shut Down Wire Fasd

Page 6

CHASSIS GROUND

Factory Bolt

Locate an easy to get to bolt or screw

located under the driver’s side of the dash and

attach the BLACK ground wire from the 11-pin Spade Connector harness securely as pictured.

Black Ground Wire

Note: Remove any paint below the spade connector.

Parking Light Output (-)(Optional part #775 required)

 

 

 

 

 

YELLOW To parking

Turn the parking lights to the ON position. (NOT YOUR HEADLAMPS).

 

 

 

 

 

 

 

 

light

Probe the wire(s) coming from your headlamp switch. Find the wire

 

 

 

 

 

 

 

 

circuit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

that will show +12V only when the parking lights are ON and ground

 

 

 

 

 

 

 

 

 

 

when the lights are OFF. Connect the YELLOW wire from part #775

WHITE

 

 

87a

 

 

 

 

to this wire. Connect the BROWN wire from the 11-pin harness to

 

 

 

 

 

 

 

Brown(-)

 

 

 

 

BLACK

 

 

 

 

 

 

 

 

the WHITE wire on part #775. Connect the BLACK and the BLUE wires

from

 

 

 

 

 

 

 

 

from part #775 to +12V constant fused at 20 amps. See diagram

module

 

 

 

 

 

 

 

above.

 

RED

 

 

 

 

 

 

+12V Fused

BRAKE INPUT

 

 

 

 

 

 

 

 

 

Do not

 

 

 

 

 

 

 

The brake wire is located on the switch near and above the brake pedal. The correct wire willat 20showamps

 

use, tape

 

 

BLUE

 

 

 

(+12V) on the test light only when the brake is pressed. Connect the BLUE WITH BLACK STRIPE from

the 11-pin harness to this wire.

off.

 

ANTENNA

For best results, run the antenna (YELLOW WITH BLACK TIP in the 11-pin harness) as straight as possible. Do not place the antenna next to any metal parts or the vehicle’s main computer control.

FACTORY ALARM SHUT DOWN WIRE (FASD) (-)

If your vehicle is equipped with a factory alarm system (as most vehicles with a factory keyless entry are) probe for a small gauge wire (usually found in the driver’s side kick panel) that shows (-) ground when the door lock cylinder is turned to the unlock position using the door key. This wire will usually show a (+) positive voltage before turning the key. NOTE: Some factory disarm wires remain neutral (shows no voltage) before you turn the key to unlock instead of +12v positive. Connect the RED WITH BLACK STRIPE wire from the 11-pin harness to this wire.

HOOD PIN SWITCH

This feature will keep the engine from starting or shut off the engine when the hood is opened. Locate a good chassis ground, if at all possible do not install the pin switch in the rain gutter. Drill a 5/16 hole, insert the pin switch into the hole and tighten. Check for the hood adjustment, there is approximately 1/4” adjustment in the pin switch. Close the hood easy, making sure that the pin switch is not keeping the hood from closing all the way, if it does, cut off approximately 1/8” of the black plastic off of the top of the hoodpin switch and try closing the hood again. Check to make sure that the hoodpin switch remains neutral when the hood is closed and shows ground when the hood is open. Plug the BLACK WITH BLUE STRIPE wire from the 18-pin harness into the bottom of the hood pin switch.

TACH INPUT (Optional)

By this time, you should have determined the way you want your vehicle to start (tach or tachless). If you have chosen the TACHLESS start option, simply proceed to the next step and skip the following instructions. Make sure you tape this wire up if not used. For TACH mode connect the BLACK WITH WHITE STRIPE wire from the 11-pin harness to the negative side of the coil or the tach wire at the coil pack under the hood. To find the coil pack follow the spark plug wires back to their termination point. To operate in tach mode, make sure to program tach option, see programming tach option page 7.

AUXILIARY INPUT

If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 11-pin harness to the second or third channel (-) output of your existing alarm. When the output is activated, a (-) signal will be supplied to the remote starter.

5

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Guide OWNER’S Guide ContentsRequired Tools System FeaturesSystem Components Technical AssistancePrecautions Making Wiring ConnectionsWire Tie Making END to END ConnectionsSTARTER/CRANK Wire +12V only in the start position Ignition Wires +12V in run and crank position onlyAccessory Wires That Power the HEATER/BLOWER Motor Locating & Making ConnectionsChassis Ground Factory Alarm Shut Down Wire FasdHood PIN Switch Brake InputConnecting the 11-PIN Harness & 4-RELAY Harness Neutral Safety SwitchHOW to USE Your Remote Transmitter Factory ANTI-THEFT SystemsProgramming Instructions

RS82 specifications

The Bulldog Security RS82 represents a cutting-edge advancement in vehicle security systems, tailored to provide top-tier protection for vehicles of various sizes. As theft and vandalism become more sophisticated, the RS82 offers a robust solution designed to keep your vehicle secure while offering convenience and user-friendly features.

One of the standout characteristics of the Bulldog Security RS82 is its powerful immobilizer function. This feature works by disabling critical engine components, rendering the vehicle almost impossible to start without the authorized key or remote. Such technology is especially crucial in today's landscape where opportunistic thefts are rampant.

Another notable attribute of the RS82 is its comprehensive alarm system. The alarm includes a loud siren, which effectively deters potential thieves, while also alerting nearby individuals to any unauthorized attempts to access the vehicle. The alarm system is equipped with a range of sensors, including shock sensors that detect vibrations and movements, ensuring that any disturbance triggers an immediate response.

Additionally, the RS82 supports remote control functionality. Users can lock or unlock their vehicle, activate or deactivate the alarm, and even locate their vehicle via GPS all through a compact remote device. This level of control adds convenience, allowing users to manage their vehicle's security from a distance.

In terms of installation, the Bulldog Security RS82 is designed for versatility. Its universal fit allows it to be installed on a variety of vehicle types, including cars, vans, and motorcycles. The system is also engineered for ease of integration, making it suitable for both professional installations and DIY enthusiasts.

Furthermore, the RS82 is built to withstand harsh weather conditions. With a durable casing that protects the internal components from moisture and debris, this security system is reliable regardless of environmental challenges.

In summary, the Bulldog Security RS82 is an exceptional vehicle security solution that combines cutting-edge technologies, including a powerful immobilizer, an effective alarm system, and convenient remote control features. Its robust design and universal fit make it an ideal choice for any vehicle owner looking to enhance security and protect their investment. With the RS82, users can enjoy peace of mind knowing their vehicle is safeguarded against theft and unauthorized access.
Top Page Image Contents