Specifications
Models LP122A Series/LP123
Volume | Up to 39.0 GPM (147.6 l/m) |
Discharge Pressure | Up to 2000* PSI (138* Bar) |
Inlet Pressure | Up to 90 PSI (6.2 Bar) |
Speed | Up to 885 RPM |
Plunger Diameter | 42 mm |
Stroke | 42 mm |
Crankcase Oil Capacity | 116 fl.oz. |
Temperature of Pumped Fluids | Up to 160oF (71oC) |
Inlet Port | |
Discharge Port | 1" NPT |
Crankshaft Mounting | Either Side |
Shaft Rotation | Top of Pulley Towards Fluid End |
Weight | 116 lbs. |
Crankshaft Diameter | 35 mm |
Valve Casing - LP122A | Aluminum Bronze |
Valve Casing - LP123 | Brass |
Valve Casing - | 303 S.S. |
Valve Casing - | Aluminum |
Volumetric Efficiency @ 800 RPM | 0.96 |
Mechanical Efficiency @ 800 RPM | 0.85 |
PULLEY INFORMATION
Pulley selection and pump speed are based on a 1725 RPM motor and "B" section belts. When selecting desired GPM, allow for a ±5% tolerance on pumps output due to variations in pulleys, belts and motors among manufacturers.
1.Select GPM required, then select appropriate motor and pump pulley from the same line.
2.The desired pressure is achieved by selecting the correct nozzle size that corresponds with the pump GPM.
HORSEPOWER INFORMATION
We recommend that a 1.1 service factor be specified when s electing an electric motor as the power source. To compute specific pump horsepower requirements, use the following formula:
HP = (GPM X PSI) / 1440
Pump speeds of 640 RPM and above require a minimum inlet pressure of 12 psig. Pump speeds of 805 RPM and above require a minimum inlet pressure of 14 psig.
LP122A SERIES/LP123 PULLEY SELECTION AND HORSEPOWER
REQUIREMENTS
GPM | PUMP | MOTOR | RPM | 600 PSI | 800 PSI | 1000 PSI | 1300 PSI | 2000 PSI | |
PULLEY | PULLEY | ||||||||
|
|
|
|
|
|
| |||
22.3 | 12.75" | 3.95" | 500 | 9.6 | 12.7 | 15.9 | 20.7 | 31.9 | |
24.7 | 12.75" | 4.35" | 555 | 10.6 | 14.1 | 17.6 | 22.9 | 35.3 | |
28.5 | 12.75" | 4.95" | 640 | 12.2 | 16.3 | 20.4 | 26.5 | 40.7 | |
30.9 | 12.75" | 5.35" | 695 | 13.2 | 17.7 | 22.1 | 28.7 | 44.1 | |
33.4 | 12.75" | 5.75" | 750 | 14.3 | 19.1 | 23.9 | 31.0 | 47.7 | |
35.6 | 12.75" | 6.15" | 800 | 15.3 | 20.3 | 25.4 | 33.1 | 50.9 | |
39.4* | 12.75" | 6.50" | 885 | 16.9 | 22.5 | 28.1 | 36.6 | 56.3 |
*Intermittent duty only! - Consult factory!
3