Installation Instructions

Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installa- tion. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.

1.The pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication.

2.The inlet to the pump should be sized for the flow rate of the pump with no unnecessary restrictions that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to be operated at temperatures in excess of

1600 F, it is important to insure a positive head to the pump to prevent cavitation.

3.The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pressure loss to the work area. It is essential to provide a safety bypass valve between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.

4.Use of a dampener is necessary to minimize pulsation at drive elements, plumbing, connec- tions, and other system areas. The use of a dampener with Giant Industries, Inc. pumps is optional, although recommended by Giant Industries, Inc. to further reduce system pulsa- tion. Dampeners can also reduce the severity of pressure spikes that occur in systems using a shut-off gun. A dampener must be positioned downstream from the unloader.

5.Crankshaft rotation on Giant Industries, Inc. pumps should be made in the direction desig- nated by the arrows on the pump crankcase. Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the charts on pages 3-6.

6.Before beginning operation of your pumping system, remember: Check that the crankcase and seal areas have been properly lubricated per recommended schedules. Do not run the pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the pump.

Finally, remember that high pressure operation in a pump system has many advantages. But, if it is used carelessly and without regard to its potential hazard, it can cause serious injury.

IMPORTANT OPERATING CONDITIONS

Failure to comply with any of these conditions invalidates the warranty.

1.Prior to initial operation, add oil to the crank- case so that oil level is between the two lines on the oil dipstick. DO NOT OVERFILL.

Use Giant Oil or Use SAE 0 W 40 when pumping CO2 under 32oF (0o C)

Crankcase oil should be changed after the first 50 hours of operation, then at regular intervals of 500 hours or less depending on operating conditions.

2.Pump operation must not exceed rated

pressure, volume, or RPM. A pressure relief device must be installed in the discharge of the system.

3.Acids, alkalines, or abrasive fluids cannot be pumped unless approval in writing is obtained before operation from Giant Industries, Inc.

4.Run the pump dry approximately 10 seconds to drain the water before exposure to freezing temperatures.

CP200, CP220, CP218, CP230 specifications

Giant's CP series represents a significant step forward in the world of compact construction machinery, with models like CP218, CP230, CP200, and CP220 leading the way. These multi-purpose compactors are specifically designed to meet the demands of a variety of construction and landscaping applications, offering powerful performance combined with user-friendly features.

The CP218 boasts a sturdy design, combined with a powerful engine that ensures efficient operation even in the most challenging conditions. Its compact size allows for easy maneuverability in tight spaces, making it an ideal choice for urban construction projects. The machine features advanced vibration technology that maximizes the compaction efficiency, delivering optimal results with minimal effort.

Next in line, the CP230 is engineered for those who require enhanced compaction force. With an upgraded engine and heavier weight, this model excels in compacting thicker layers of material. The CP230 incorporates an ergonomic design with a user-friendly control panel, ensuring operators can easily manage the machine even during extended periods of use. Additionally, it features an integrated water spraying system that helps keep the surface moist, preventing dust and ensuring consistent compaction.

The CP200 stands out for its versatility. This model is equipped with a variety of attachments, allowing it to perform multiple tasks effectively. Whether it's compacting soil, asphalt, or aggregate, the CP200 adapts seamlessly to the job at hand. Its lightweight structure and foldable handlebars make transport and storage a breeze, catering to contractors with space constraints.

Lastly, the CP220 ranks as a mid-range solution that balances power and efficiency. This model integrates noise-reduction technologies, ensuring quieter operation without sacrificing performance. Its intuitive controls and safety features, such as automatic shutoff and vibration isolation, make it suitable for both novice and experienced operators alike.

All models in the Giant CP series are built with durability in mind, geared to withstand the rigors of daily use on construction sites. They are equipped with reliable engines and robust frames, ensuring a long lifespan and reduced maintenance costs. Overall, the Giant CP218, CP230, CP200, and CP220 provide an impressive combination of performance, versatility, and ease of use, making them essential tools for any contractor looking to enhance their efficiency on the job.