GARDENA WP1200 Pumps: User Manual for Garden Spring Pump Models WP 600, 1200 & 1800

GARDENA Garden Spring Pump WP 600 / WP 1200 / WP 1800

Welcome to the Garden of GARDENA ...

The pump must not be operated when there are people in the water.

Swimming pools and garden ponds should be designed according to international and national design regulations.

Protect the power cable from heat, oil and sharp edges.

User instructions:

Never let the pump run dry; running dry generates heat and will damage the pump.

This is the translation of the original German User’s Manual. Please read the User’s Manual carefully and comply with them. Use this User’s Manual to familiarise yourself with the pump, its proper use and the safety instructions.

For safety reasons, children under 16 as well as persons not familiar with this User’s Manual must not use this pump.

vKeep this User’s Manual in a safe place.

1. Where to use your GARDENA Garden Spring Pump. . . . . . . . . 8

2. Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

vPlease consult a professional electrician.

Before operating the pump, look to see if there is any damage to the pump (esp. regarding power cable and plug).

The connection cable of the pump cannot be replaced. If the cable is damaged the pump must be scrapped.

Do not use the power cable to carry the pump or to pull the plug out of the socket.

The temperature of the liquid used must not be below 4 °C or above 35 °C.

Sand and other abrasive substances in the liquid cause increased wear and reduce the output of the pump.

Please observe the local noise prevention regulations.

3. Initial Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4. Storing your Fountain Pump Set . . . . . . . . . . . . . . . . . . . . . . . 10

3. Initial Operation

5. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6. Trouble-shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

8. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

9. Service / Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Commissioning the pump:

1.	Screw the stepped nipple 1 on to the pump outlet 2.
2.	Connect the stepped nipple 1 to the spring / gargoyle with
	a hose (1⁄2” or 3⁄4”).
3.	Install the pump at ground level so that the filter housing 3 is
	standing in water to at least half its height.
4.	Insert the pump plug into a mains socket.
	Caution: The pump will start immediately.

1. Where to use your GARDENA Fountain Pump set

5. Use the flow control 4 to set the desired water flow for the

spring / gargoyle.

Intended Use:

Please note

The GARDENA Garden Spring Pump is intended for domestic use for supplying water to springs and gargoyles. It is not designed for operating watering equipment and accessories or irrigation systems. The pump can be used both indoors and outdoors.

The GARDENA Garden Spring Pump is not suitable for continuous operation in industrial applications. Corrosive, easily combustible, aggressive or explosive substances (such as gasoline, petroleum or nitro thinners), or saltwater must not be pumped, nor must foodstuffs or drinking water.

Commissioning the pump if it is installed out of water:

3 5 7

If the pump is installed out of water, the filter housing 3 must be taken off.

1. Pull off the filter housing 3.
2.	Turn the pump inlet 5 anticlockwise and pull it vertically off the
	motor housing 6 (bayonet socket).
3.	Depending on the pumping application, the pump inlet can
	be rotated in 90° steps. Twist the pump inlet 5 accordingly,
	again press it vertically on to motor housing 6 and tighten it

2. Safety instructions

	Electrical Safety:	v Please ask your electrician for his advice.
	DANGER ! Electric shock !	Mains power cables should not have a smaller
	v Always disconnect the pump	cross-section than a rubber sheathed cable
	v Always disconnect the pump	of the designation H05 RN-F3G0,75.
	from the mains before under-	of the designation H05 RN-F3G0,75.
	from the mains before under-	Extension cables must meet the requirements
	taking any work on it.	Extension cables must meet the requirements
	taking any work on it.	of DIN VDE 0620. Check line voltage.
		of DIN VDE 0620. Check line voltage.
	The pump should be operated via a residual	Data indicated on the type plate must match
	The pump should be operated via a residual	technical data of the mains supply.
	current device with a residual current rating of	technical data of the mains supply.
	≤ 30 mA (DIN VDE 0100-702 and 0100-738). The	Please unplug the pump after operation and
	pump must be placed on solid, even ground.	before carrying out any maintenance works.

	clockwise (see 5. Cleaning).
4.	Screw stepped nipples 7 on to the pump inlet 5 and
	pump outlet 2.
5.	Connect the pump inlet 5 to the water reservoir with a hose
	(1⁄2” or 3⁄4”). The level in the water reservoir must be highert-
	han the pump inlet 5.
6.	Connect the pump outlet 2 to the spring / gargoyle with a
	hose (1⁄2” or 3⁄4”).
7. Fill the hose to the pump inlet 5 with water.
8.	Insert the pump plug into a mains socket.
	Caution: The pump will start immediately.
9.	Use the flow control 4 to set the desired water flow for the
	spring.

WP1200, WP 1800, WP 600 specifications

The Gardena WP line of water pumps, comprising the WP 600, WP 1200, and WP 1800 models, stands out in the market for their reliability and efficiency in various water management tasks. Designed with user convenience and high performance in mind, these pumps cater to different needs in gardening, irrigation, and general water supply.

The WP 600 is a compact and lightweight model ideal for small gardens and watering tasks. With a power output of 600 watts, it delivers a maximum flow rate of around 3,300 liters per hour and a pump height of up to 35 meters. This model incorporates the innovative Gardena "Quick Connect" system, which allows users to easily connect hoses and fittings without the need for additional tools. Additionally, the WP 600 features a robust design that includes a built-in filter to prevent dirt and debris from entering the pump, thereby extending its lifespan.

Moving up in power, the WP 1200 is geared toward more extensive gardening and irrigation needs. It boasts a 1200-watt motor, allowing for a higher flow rate of approximately 4,600 liters per hour and a pump height of 42 meters. The WP 1200 is equipped with a user-friendly control panel, making operation straightforward for both experienced users and beginners. A thermal overload protection feature ensures that the pump doesn't overheat, an essential safety measure enhancing its longevity. The WP 1200 also includes a carry handle, making it easy to transport between locations.

At the top of the WP range, the WP 1800 sets the standard for high-performance water pumps. With an output of 1800 watts, this model achieves an impressive flow rate of 5,500 liters per hour and a maximum delivery height of 48 meters. The WP 1800 comes with advanced features such as an integrated pressure switch that automatically activates and deactivates the pump as needed, optimizing energy consumption. This model is particularly suitable for larger-scale irrigation systems and can effectively handle both clean and slightly dirty water, making it versatile for different applications.

In summary, Gardena's WP 600, WP 1200, and WP 1800 pumps offer a range of features tailored to various water management tasks. With durability and efficiency at the forefront, these pumps incorporate innovative technologies, ensuring reliable performance for every user, whether tending to a small garden or managing a more extensive irrigation system.

Gardena Essential Guide to GARDENA Garden Spring Pumps for Effective Watering Solutions