Harbor Freight Tools 93820, 93819 manual Inspection, Maintenance, And Cleaning

Page 10
Cord (1) or Discharge Pipe. (See Figure E.)

7.Carefully set the Pump in place. Do not lower or raise the Pump by its Power

Cord (1) or Discharge Pipe. (See Figure E.)

8.The Float Switch (2) automatically switches on and off at a water depth of ap- proximately 4 inches. The ON/OFF height can be manually adjusted by adjusting the Float Switch Lock. CAUTION: Do not run the Pump dry. Doing so will increase wear to the unit and possibly cause seal damage. (See Figure E.)

9.NOTE: This Pump has a built-in thermal protector for the Motor which automati- cally shuts it off to avoid overheating. After the Motor cools, it will cycle back on. Wait for the cycle to continue. Do not try to turn on the Pump manually after it has automatically shut off.

10.Connect additional Discharge Pipe as needed to direct the water discharge to the desired location. The discharge should be kept as short as possible with a mini- mum number of turns. IMPORTANT: Do not exceed the maximum lift of the Pump:

1 HP Model 93819 = 26 Feet.

1.2 HP Model 93820 = 28 Feet.

11.Connect the Power Cord & Plug (1) to its 120 volt, GFCI electrical outlet, while making sure to form a “drip loop” in the Power Cord. (See Figure A.)

12.When the water level exceeds approximately 4 inches the Pump will automatically turn on and run continuously until the water level falls below 4 inches at which time the Pump will automatically turn off.

13.WARNING! When shutting off power to the Pump, always shut off the electrical power to the GFCI outlet first. Then, disconnect the Pump’s Power

Cord & Plug (1) from the GFCI outlet.

INSPECTION, MAINTENANCE, AND CLEANING

1.WARNING! Always shut off the electrical power to the GFCI outlet first.

Then, disconnect the Pump’s Power Cord & Plug (1) from the GFCI outlet prior to performing any inspection, maintenance, or cleaning procedures.

2.Before each use, inspect the general condition of the Pump. Check for cracked or broken parts, damaged electrical wiring, clogged Impeller Cover, Impeller, Dis- charge Pipes, and any other condition that may affect safe operation. If abnor- mal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment.

3.To clean the Impeller Cover and Impeller: A clogged or dirty Impeller Cover

SKU 93819

For technical questions, please call 1-800-444-3353

PAGE 10

93820

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents SUBMERSIBLE DIRTY WATER PUMP For technical questions, please callASSEMBLY AND OPERATING INSTRUCTIONS Model 93819 - 1 HP Model 93820 - 1.2 HPSAVE THIS MANUAL PRODUCT SPECIFICATIONSGENERAL SAFETY RULES WORK AREAPERSONAL SAFETY ELECTRICAL SAFETY2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes SERVICE SPECIFIC SAFETY RULESTOOL USE AND CARE FIGURE A 8. Make sure to position the Pump on a flat, level, solid surfaceDrip Loop OUTLET PUMP DEVICE OUTLET CORD14. Industrial applications must follow OSHA requirements 11. NEVER raise or lower the Pump by its electrical Power CordGROUNDING SAVE THESE INSTRUCTIONSFIGURE C GROUNDED TOOLS TOOLS WITH THREE PRONG PLUGSFIGURE B DOUBLE INSULATED TOOLS TOOLS WITH TWO PRONG PLUGS THIS PRODUCT USES A 3-PRONG ELECTRICAL PLUG 120 VOLT GROUNDEDUNPACKING SYMBOLOGYASSEMBLY AND OPERATING INSTRUCTIONS FIGURE DPOWER CORD & PLUG See Figure EFIGURE E FLOAT SWITCH LOCK 1/8” AIR BLEED HOLECord 1 or Discharge Pipe. See Figure E INSPECTION, MAINTENANCE, AND CLEANING1 HP Model 93819 = 26 Feet 1.2 HP Model 93820 = 28 Feet FIGURE F TROUBLESHOOTINGSee Figure F and Assy. Diagram ProblemPARTS LIST PLEASE READ THE FOLLOWING CAREFULLYand are not available individually as replacement parts ASSEMBLY DIAGRAMSome parts are listed and shown for illustration purposes only 3491 Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800 Limited 1 year / 90 Day warranty
Top Page Image Contents