Harbor Freight Tools 93819, 93820 Grounded Tools Tools With Three Prong Plugs, Figure C, Volt

Page 7
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

1.Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of elec- tric shock. (See Figure B.)

2.The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure B.)

3.Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure B.)

THIS PRODUCT

USES A

3-PRONG

ELECTRICAL

PLUG

120 VOLT,

GROUNDED,

ELECTRICAL OUTLET

FIGURE B

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

4.Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure C.)

5.Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure C.)

THIS PRODUCT DOES NOT USE A 2-PRONG ELECTRICAL PLUG

120 VOLT,

GROUNDED,

ELECTRICAL OUTLETS

FIGURE C

SKU 93819

For technical questions, please call 1-800-444-3353

PAGE 7

93820

 

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model 93819 - 1 HP Model 93820 - 1.2 HP For technical questions, please callASSEMBLY AND OPERATING INSTRUCTIONS SUBMERSIBLE DIRTY WATER PUMPWORK AREA PRODUCT SPECIFICATIONSGENERAL SAFETY RULES SAVE THIS MANUALPERSONAL SAFETY ELECTRICAL SAFETY2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes SERVICE SPECIFIC SAFETY RULESTOOL USE AND CARE OUTLET PUMP DEVICE OUTLET CORD 8. Make sure to position the Pump on a flat, level, solid surfaceDrip Loop FIGURE ASAVE THESE INSTRUCTIONS 11. NEVER raise or lower the Pump by its electrical Power CordGROUNDING 14. Industrial applications must follow OSHA requirementsTHIS PRODUCT USES A 3-PRONG ELECTRICAL PLUG 120 VOLT GROUNDED GROUNDED TOOLS TOOLS WITH THREE PRONG PLUGSFIGURE B DOUBLE INSULATED TOOLS TOOLS WITH TWO PRONG PLUGS FIGURE CFIGURE D SYMBOLOGYASSEMBLY AND OPERATING INSTRUCTIONS UNPACKINGFLOAT SWITCH LOCK 1/8” AIR BLEED HOLE See Figure EFIGURE E POWER CORD & PLUGCord 1 or Discharge Pipe. See Figure E INSPECTION, MAINTENANCE, AND CLEANING1 HP Model 93819 = 26 Feet 1.2 HP Model 93820 = 28 Feet Problem TROUBLESHOOTINGSee Figure F and Assy. Diagram FIGURE FPLEASE READ THE FOLLOWING CAREFULLY PARTS LISTand are not available individually as replacement parts ASSEMBLY DIAGRAMSome parts are listed and shown for illustration purposes only Limited 1 year / 90 Day warranty 3491 Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800
Top Page Image Contents