Harbor Freight Tools 93820 Grounding, NEVER raise or lower the Pump by its electrical Power Cord

Page 6
11.NEVER raise or lower the Pump by its electrical Power Cord.

10.If necessary, have a certified electrician install (within 14 feet of where the

Pump will be located) a 120 volt, GFCI electrical outlet that is dedicated only to the Pump. Any outlet should be above the water line.

11.NEVER raise or lower the Pump by its electrical Power Cord.

12.In cold weather, when the Pump is not in use, protect the interior of the Pump from freezing by draining the water and pumping a permanent type automobile anti-freeze containing a rust inhibitor through the system. A

50% mixture with water is recommended. Be sure to flush the system with a neutralizing liquid prior to re-use of the Pump.

13.Prior to use, and periodically thereafter, check to make sure all connections are tight and secure.

14.Industrial applications must follow OSHA requirements.

15.Performance of this product may vary depending on variations in local line voltage.

16.WARNING! People with pacemakers should consult their physician(s) be- fore using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker.

17.WARNING! The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

GROUNDING

14.Industrial applications must follow OSHA requirements. WARNING!

Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

SKU 93819

For technical questions, please call 1-800-444-3353

PAGE 6

93820

 

 

Image 6
Contents SUBMERSIBLE DIRTY WATER PUMP For technical questions, please callASSEMBLY AND OPERATING INSTRUCTIONS Model 93819 - 1 HP Model 93820 - 1.2 HPSAVE THIS MANUAL PRODUCT SPECIFICATIONSGENERAL SAFETY RULES WORK AREAELECTRICAL SAFETY PERSONAL SAFETY2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes SPECIFIC SAFETY RULES SERVICETOOL USE AND CARE FIGURE A 8. Make sure to position the Pump on a flat, level, solid surfaceDrip Loop OUTLET PUMP DEVICE OUTLET CORD14. Industrial applications must follow OSHA requirements 11. NEVER raise or lower the Pump by its electrical Power CordGROUNDING SAVE THESE INSTRUCTIONSFIGURE C GROUNDED TOOLS TOOLS WITH THREE PRONG PLUGSFIGURE B DOUBLE INSULATED TOOLS TOOLS WITH TWO PRONG PLUGS THIS PRODUCT USES A 3-PRONG ELECTRICAL PLUG 120 VOLT GROUNDEDUNPACKING SYMBOLOGYASSEMBLY AND OPERATING INSTRUCTIONS FIGURE DPOWER CORD & PLUG See Figure EFIGURE E FLOAT SWITCH LOCK 1/8” AIR BLEED HOLEINSPECTION, MAINTENANCE, AND CLEANING Cord 1 or Discharge Pipe. See Figure E1 HP Model 93819 = 26 Feet 1.2 HP Model 93820 = 28 Feet FIGURE F TROUBLESHOOTINGSee Figure F and Assy. Diagram ProblemPARTS LIST PLEASE READ THE FOLLOWING CAREFULLYASSEMBLY DIAGRAM and are not available individually as replacement partsSome parts are listed and shown for illustration purposes only 3491 Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800 Limited 1 year / 90 Day warranty