Harbor Freight Tools 68375 Locating the Water Pump, Strainer must be fully immersed in water

Page 9

Locating the Water Pump

Locate the Water Pump on a flat, level, sturdy surface capable of supporting the weight of the Pump.

1.For best Pump performance, place the Pump near the water level and use hoses that are no longer than necessary. This will allow the Pump to produce the greatest output with the least self-priming time. See diagram below.

Discharge Head

Total Head

 

Suction

Water Pump

Head

As the head (pumping height) increases, pump output decreases. The length, type, and size of the suction and discharge hoses can also significantly affect Pump output.

Discharge head capability is always greater than suction head capability. This means pumping height for the Intake Hose (suction head) should be shorter than the pumping height for the Discharge Hose.

Minimizing suction head (placing the Pump closer to the water level) will also help reduce self-priming time. This is the time it takes the Pump to bring the water from the water level to the Pump during the initial operation.

2.Route the Intake Hose with the Intake Strainer fully immersed in the water supply source.

3.Place Strainer into water to be pumped. CAUTION:

Strainer must be fully immersed in water.

Do not operate Pump without Strainer connected to end of suction hose. Keep Strainer out of sand or silt by placing Strainer in a bucket or on stones.

NOTICE: If there is an air leak in the suction line, you may not be able to prime the pump. Use of a thread sealant is recommended.

Strainer

4.Secure the Intake Hose in place to keep it from moving once the Pump is turned on. The Intake Hose should be as short as possible for more efficient operation.

5.Route the discharge hose to the desired discharge location. If necessary, connect additional discharge hoses to direct the discharge to the desired location. Make sure to secure the discharge hose in place to keep it from moving once the Water Pump is turned on. The discharge hose should be kept as short as possible for more efficient operation.

Operation Concerns

1.Cavitation: This is the sudden formation and collapse of low-pressure vapor (bubbles) across the vanes of the impeller.

Cause: When the surface pressure on a liquid becomes low enough, the liquid will begin to boil (even at room temperature). With centrifugal pumps, cavitation can occur when the suction vacuum becomes too great, allowing water vapor or bubbles to form at the impeller. The rapid pressure increase can cause impeller damage.

Solution: Minimizing suction head and using the largest practical suction hose diameter will reduce the likelihood of cavitation. Do not use a suction hose with a diameter smaller than the Pump’s Intake Port (2″ diameter).

2.Water Hammer Pressure: This is energy sent back to the Pump due to sudden stoppage of water flowing from the Pump.

Cause: Water hammer pressure is more likely to occur when using a very long discharge hose. If the flow of water at the end of the discharge hose is shut off suddenly, energy is sent back to the pump. This causes a large pressure spike in the Pump housing, leading to potential damage to the Pump casing.

Solution: Use as short a discharge hose as possible and turn off water pump before closing water flow.

Item 68375

For Pump technical questions, please call 1-800-444-3353.

Page 7

 

For Engine technical questions, please call 1-800-520-0882.

 

Image 9
Contents Using an engine indoors can Kill YOU Gasoline Powered Clear Water PumpPump SpecificationsSet up Precautions Symbol DefinitionsSafety Warnings Symbol Property or StatementCarbon Monoxide Hazard Using an engine indoors can Kill Engine Precautions Operating PrecautionsRefueling Service PrecautionsControls Connecting Hoses Set upDischarge Port Locating the Water Pump Strainer must be fully immersed in waterOperation Concerns Operation Pre-Start ChecksPrime the Pump Checking and Filling Engine Oil Checking and Filling FuelStarting the Engine Break-in Period Stopping the EngineMaintenance and Service Cleaning, Maintenance, and Lubrication ScheduleEngine Oil Change 10W-30 5W-30Cleaning Air Filter Element MaintenanceSpark Plug Maintenance Cap Recommended Spark PlugStorage BatteryFuel Air Filter Cover Muffler Carburetor Drain Bolt LubricationProblem Possible Causes Likely Solutions Pump TroubleshootingProblem Possible Causes Probable Solutions Engine TroubleshootingDo not use gasoline with more than 10% ethanol E15, E20, E85, etcCompression Related section Use Engine will not startPart Description Qty Parts List Including Item 68120 212cc engineDiagram Including Item 68120 212cc engine United States Emission Control Defects Warranty Statement Emission Control System WarrantyManufacturer’s Warranty Coverage WarrantiesLength of Coverage Mission Oaks Blvd. PO Box 6009 Camarillo, CA

68375 specifications

Harbor Freight Tools is well-known for providing high-quality tools and equipment at affordable prices, and the Harbor Freight Tools 68375 is no exception. This versatile and powerful tool is designed to meet the needs of both DIY enthusiasts and professionals alike. The 68375 model is particularly favored for its robust features and user-friendly design.

One of the standout characteristics of the Harbor Freight Tools 68375 is its powerful motor. The tool is equipped with a high-efficiency motor that delivers impressive performance, making it suitable for various applications, from automotive repairs to woodworking projects. Users can expect a reliable power output, which enhances productivity and helps accomplish tasks with precision.

Another key feature of the 68375 is its ergonomic design. The tool is crafted with user comfort in mind, boasting a lightweight structure and intuitive controls. This ensures that even during extended use, operators experience minimal fatigue. The grip is designed to provide maximum control, allowing for precise handling, which is particularly important for intricate tasks.

The Harbor Freight Tools 68375 also integrates advanced safety features that enhance user experience and peace of mind. These include protective guards and safety switches that prevent accidental starts, ensuring that users can operate the tool without unnecessary risks. This focus on safety is a critical consideration for Harbor Freight, reflecting their commitment to customer satisfaction.

Furthermore, the 68375 model is designed for versatility. It comes with multiple attachments and accessories, allowing users to tackle a broad range of projects. Whether you are drilling, sanding, or cutting, this tool adapts easily, making it a valuable addition to any toolkit.

Additionally, the durability of the Harbor Freight Tools 68375 is impressive. Constructed with high-grade materials, it withstands the rigors of daily use, ensuring that it remains reliable over time. This durability is complemented by Harbor Freight's reputation for quality assurance, which further solidifies the trust users place in their products.

In summary, the Harbor Freight Tools 68375 is a well-rounded tool that excels in power, comfort, safety, and versatility. Its thoughtful design and robust features make it a preferred choice among both hobbyists and professionals. Whether for personal projects or professional commitments, the 68375 stands out as an essential tool that delivers consistent performance and reliability. This model exemplifies Harbor Freight's commitment to affordability without compromising on quality, making it a wise investment for anyone in need of a reliable addition to their toolbox.