Bissell 7950 warranty Possible Causes Remedies

Page 21

Troubleshooting Continued

DirtLifter PowerBrush does not turn.

Possible Causes

Remedies

1 The Brush Belt or Pump Belt is off or broken

1 Turn the machine OFF and unplug from

 

the outlet. To check if a Pump Belt has

 

broken, you will need a flat head screwdriver.

 

Insert the blade end into the lower slot of the

 

Belt Access door to release the lower snap. If

 

necessary, insert the blade end into the upper

 

slot to release the upper snap. Examine the

 

belt for breakage. If broken refer to pages 18-19.

Carpet Protector is not spraying.

Possible Causes

1Bottle not connected properly to the tool.

2Solution clogging the Spray trigger.

3Applicator tool spray is blocked.

4SmartMix not set on water/rinse

carpet protector setting.

5ReadyTool dial not set on tool setting.

Cleaner not picking up solution.

Possible Cause

1Ready Tools dial may be at the wrong setting for the cleaning job.

2Nozzle Window may not be properly attached.

3Tank-in-Tank lid is not properly installed.

4Tank-in-Tank is not properly seated.

5Poor tool position. (Hand held attachments only).

6Tank-in-Tank has picked up maximum dirty water.

Remedies

1Follow instructions on cartridge

assuring proper fit.

2Soak applicator tool only in hot water. Spray without the cartridge attached to purge any residual Solution left in the tool.

3Soak applicator tool only in hot water.

Spray without the cartridge attached to purge any residual Solution left in the tool.

4Set to proper setting.

5Set to tool setting.

Remedies

1Set ReadyTools dial to either Tools or PreTreat or Floor Cleaning.

2Press down firmly on the black oval gasket at the top window to make sure the two tabs on the back of the Nozzle Window are snapped into the mating slots in the main housing.

3Re-install lid; refer to The Operations section, page 10

4Tank-In-Tank must be firmly seated to function; remove and reseat Tank-in-Tank.

5Adjust angle; apply more downward pressure.

6Empty Tank-in-Tank, refer to The Operations section, page 10

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents ProHeat Thanks for buying a Bissell ProHeat Self Propelled Important Safety Instructions Tough Stain PreCleaner Formula withReadyTools 4 Upholstery Tool Tough Stain Brush How to Put It Together How to Use This GuideRefer to Assembly Diagram on ProHeat assembly is now completeSmartTemp Ready Light indicates when the heater is Push the handle slightly forward to engageWill not allow it to exceed SmartMix DirtLifter PowerBrushReplace the valve cap turning until snug Replace SmartMix concentrate TankLid Tank-in-TankFlow Indicator When It’s Time to Empty Tank-in-TankFinal cleanup ReadyTools DialFloor Cleaning Before You Clean CarpetsOperation Machine PreparationCleaning Formula Carpet CleaningSolution or water only Result in premature belt failureStain Removal Residue with a sweeper or vacuumNot use a knife or other utensil with sharp edges When You’re Done AssemblyTurboBrush UseImmediately after cleaning and rinsing your carpets, empty Flush water through the hose to eliminate cleaning solutionScotchgard protector Applicator Optional May bleed through fabric when wet Cleaning TechniqueImportant Check Upholstery Tags Set SmartMix Dial to NormalCleaning Bare Floors Floor Cleansing Formula in the SmartMix TankAttach the Bare Floor Tool Bare Floor Cleaning Technique Routine MaintenanceWipe all exterior surface with a soft cloth Turn the machine OFF 0 and unplug from the wall outlet Pump Belt Replacement Locate and remove broken pump belt Step on the Handle Release and recline the handle down ontoAssembly is now complete To Install the Replacement Pump BeltPlace the black brush arm onto the brush and slide black See illustrationClean out Flow Indicator Filter, TroubleshootingPossible Cause RemediesPossible Causes Possible Causes RemediesAm 10 pm ET Bissell Consumer ServicesItem Part No Part Name Warranty
Related manuals
Manual 24 pages 1.55 Kb
Top Page Image Contents