Euro-Pro EP922H owner manual Operating Instructions, Using Your Steam Cleaner with Floor Brush

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Attaching the Shoulder Strap

Using the detachable shoulder strap allows for greater freedom of movement when both hands are needed for various cleaning tasks.

To attach the shoulder strap to the steam cleaner, simply snap the shoulder strap hooks onto the connecting rings on the unit body. See Fig. 17, 18 & 19.

Fig. 17

Fig. 18

Fig. 19

Assembling the Caddy

The casters for the caddy for the portable steam cleaner are packed and shipped unassembled. To assemble the casters to the caddy, simply insert the caster stem into one of the four (4) holes in the base and push downward with the palm of your hand. (Fig. 20.) Repeat for the next three (3) casters.

Fig. 20

Attaching the Portable Steam Cleaner to the Caddy

1.After you have inserted the castors to the base of the caddy, turn the caddy right side up on a flat, level surface. Place it with the rear locking latch to your right.

2.Hold the portable steam cleaner with the power cord also to your right.

3.Insert the left side of the portable steam cleaner (#1 in the illustration below) down into the caddy making sure that it clips into the front locking tab.

4.Then press down on the right side of the portable steam cleaner (#2 in the illustration below) so that the rear locking latch locks in place. (Fig. 21)

Using Your Steam Cleaner with Floor Brush

Step 1: Connect one of the extension tubes to the hand grip on the flexible steam hose. To attach the extension tubes one onto the other or onto the hand grip, press the locking button ensuring that it fits into the hole. (Fig. 2, Fig. 3) To disconnect, repeat the operation by pressing the locking button and pulling the two sections apart.

Fig. 2 Fig. 3

NOTE: Fit floor brush with the angle adapter on to the extension tube.

Step 2: If the angle adapter is not attached to the floor brush, hold the brush with its bristles up in your left hand. With the angle adapter pointing downward, insert it into the hole in the back of the brush, then turn the floor brush 180°.

Step 3: Insert the electrical power cord into the wall outlet. Heating time is approximately 8-10 minutes with cold water. Filling the steam generator with hot water will shorten the heat up time.

Cleaning the Floor Brush

To clean the floor brush after you have finished using:

Attaching a Towel to the Floor Brush

100% white terry cloth towel can be fitted on this brush, so as to absorb the dirt and protect delicate surfaces.

Important: Please note that bristles may break through thin towels. To cut and make your own towels, we recommend that you use one (1) towel 8” x 17” folded in half or two (2) towels 4” x 17” laid one on top of the other be used. This will ensure that the brush bristles do not break through and that the towels will be sufficiently absorbent and retain as much dirt as possible.

Very Important: When installing the towels to the floor brush, ensure that the towels do not cover the front and the back of the brush. (See Fig. 9)

Fig. 5

1.Prepare white terry cloth towel:

size 8” x 17” folded in half or place one on top of another to have two layers. (Fig. 5)

2.Place the brush on top of the towel.

IMPORTANT: When using the portable steam cleaner with the shoulder strap, avoid rocking or tilting the unit excessively as this may cause water to enter the hose and be discharged along with the steam.

Front

Locking

TabRear

Locking

Latch

Fig. 21

1.Lift the front clip on the floor

brush (Fig. 4) and remove the brush.

2.Rinse the bristle brush and the diffuser housing under warm water.

3.Replace bristle brush onto the diffuser housing.

Fig. 4

Fig. 6

3. Fold the towel as shown in Fig. 6.

9

6