GE PNSF35B, GXSF23Z01 owner manual Safety Precautions

Page 3

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of electric shock, property damage or personal injury.

SAFETY PRECAUTIONS

Safety Instructions

■Check and comply with your state and local codes. You must follow these guidelines.

■Use care when handling the water softening system. Do not turn upside down, drop, drag, or set on sharp protrusions.

■Water softening systems using sodium chloride (salt) for regeneration add sodium to the water.

Persons on sodium restricted diets should consider the added sodium as part of their overall intake. Potassium chloride can be used as an alternative to sodium chloride.

■Keep the salt hole cover in place on the softener unless servicing the unit or refilling with salt.

■The water softening system works on 24 volt-60 Hz electrical power only. Be sure to use only the included transformer.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Operating Instructions

PROPER INSTALLATION

This water softening system must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive Installation Instructions, you can receive one by calling us toll-free at the GE Answer Center® 800.626.2000.

■Install or store where it will not be exposed to temperatures below freezing or exposed to any type of weather. Water freezing in the system will break it. Do not attempt to treat water over 120°F.

■Do not install in direct sunlight. Excessive sun heat may cause distortion or other damage to non- metallic parts.

■Properly ground to conform with all governing codes and ordinances.

■Use only lead-free solder and flux for all sweat- solder connections, as required by state and federal codes.

■The water softening system requires a minimum water flow of three gallons per minute at the inlet. Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve to reduce the flow

if necessary.

WARNING: Discard all unused parts and packaging material after installation. Small parts remaining after the installation could be a choke hazard.

Troubleshooting Tips

Read and follow this Safety Information carefully.

SAVE THESE INSTRUCTIONS

3

Customer Service

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Part No C1002P008 Pub. No -500357-99 JR Water Softening SystemOperating Instructions Safety InformationService Telephone Congratulations You are Now Part of the GE FamilySafety Precautions Rated capacity Specification guidelinesService flow rate Water temperature maximum FAbout the water softener system Set Water Hardness Number Control Settings RequiredSpecification Guidelines table on Set Present Time of DaySet Regeneration Starting Time Feature Optional Recharge ControlsFeature Program Memory Feature/Service Automatic Electronic DiagnosticsERR Service Control/Softener, Service Checkout ProcedureTo remove an error code 1 Unplug transformer Power lossOperating If the water softening system does not draw brine, check Care and cleaning of the water softening systemElectronic Diagnostics Checking the Salt Storage Level and RefillingSanitizing Procedure Cleaning Iron Out of the Water Softening SystemBreaking a Salt Bridge Care and cleaning of the water softener systemClean the Nozzle and Venturi Assembly Tighten the cap or housingBefore you call for service… Water Problem Possible Causes What To Do No soft waterWater. Note Be sure sample Single lever kitchen faucet, ifPage Page We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Warrantor General Electric Company. Louisville, KY GE Water Softening System WarrantyGE Will Replace What GE Will Not CoverGE Answer Center Service Telephone Numbers

GXSF23Z01, PNSF35B specifications

The GE PNSF35B and GXSF23Z01 are two advanced models of refrigerators manufactured by General Electric, renowned for their innovation and commitment to energy efficiency. These refrigerators incorporate a range of cutting-edge technologies aimed at enhancing food preservation while maintaining a user-friendly interface.

The GE PNSF35B stands out due to its spacious interior and high storage capacity, designed to meet the needs of families and individuals alike. With a counter-depth design, it seamlessly blends into kitchen cabinetry, providing a sleek appearance without sacrificing space. One of the primary features of the PNSF35B is the Advanced Cooling System, which ensures a consistent temperature throughout the refrigerator. This feature is crucial for preserving the freshness of fruits, vegetables, and perishable goods.

Another notable characteristic of the PNSF35B is its smart technology integration. It comes equipped with Wi-Fi connectivity, allowing users to control the appliance remotely through a mobile app. This capability includes temperature adjustments, alerts for door openings, and even a grocery list feature, providing convenience for the modern consumer.

On the other hand, the GXSF23Z01 model is designed with a focus on sustainability and energy efficiency. It features the Energy Star certification, indicating its ability to reduce energy consumption without compromising performance. This model incorporates LED lighting that not only enhances visibility but also consumes less energy compared to traditional lighting solutions.

The GXSF23Z01 also boasts a unique water and ice dispenser, which provides chilled water and ice at the touch of a button. This feature is optimized for ease of use, making it an essential addition to any kitchen. Moreover, the model includes adjustable shelving and a versatile interior layout, allowing users to customize the storage experience to accommodate various food and beverage items.

In conclusion, both the GE PNSF35B and GXSF23Z01 refrigerators encapsulate General Electric's commitment to quality, innovation, and sustainability. With their modern designs, advanced cooling technologies, and user-friendly features, these models are ideal choices for consumers seeking reliable and efficient refrigeration solutions that cater to contemporary lifestyles.
Top Page Image Contents