Brother 885-V51, XE5427-001 operation manual Hand as shown below

Page 41

————————————————————————————————————————————————————

fSlide the spool cap onto the spool pin and return the spool pin to its original position. Slide the spool cap as far as possible to the right as shown, with the rounded side on the left.

hPass the thread behind the thread guide cover and to the front.

While holding the thread near the spool with your right hand, pull the thread with your left

hand as shown below.

1

CAUTION

●If the spool or the spool cap is not positioned correctly, the thread may become tangled around the spool pin or the needle may break.

gPull the thread from the spool and pass the thread under the hook of the thread guide.

a

aThread guide

a

bd

c

aThread guide cover

bThread guide spring

cThread

dWhen the presser foot lever is lowered

Note

zWhen passing the thread behind the thread guide cover, be sure to use both hands. If you do not hold the thread with your right hand, the thread will be loose and you will not be able to secure the thread in the thread spring guide. It may cause incorrect thread tension.

zMake sure that the presser foot lever is raised before passing the thread behind the thread guide cover. If the presser foot lever is lowered, the thread guide spring is shut and you cannot hang the thread on the thread guide spring correctly.

iPassshownthebelow.thread through the guides in the order

3

1

4 2

Upper Threading 39

Image 41

Contents Product Code Page Introduction Important Safety InstructionsFor repair or adjustment For Users in the UK, EIRE, Malta and Cyprus only Page Contents Care and Maintenance Using the Memory FunctionTroubleshooting EmbroideringUSB port Machine FeaturesIncluded accessories AccessoriesFollowing are available as optional accessories Optional accessoriesFront view Names of Machine Parts and Their FunctionsRight-side/rear view Needle and embroidery foot sectionStart/stop button Operation buttonsLCD liquid crystal display touch panel Operation panelPage Getting Ready Basic Steps for Embroidering Turning the Machine On/Off Power supply precautionsDUnplugjack. the power cord from the power supply CUnplug the power supply cord from the electrical outletTurning on the machine Turning off the machineAttaching the Embroidery Unit Embroidery unit precautionsAttaching the embroidery unit AMake sure that the machine is turned offCarriage moves to its initial position CTurn on the machineConfirmation message is displayed ARemove the embroidery frame Removing the embroidery unitBPress , and then press CTurn off the machineViewing the LCD LCD Liquid Crystal Display OperationPattern type selection Moves the embroidery unit carriage to its storage positionChanging the machine settings DWhen settings are complete, press Back key BPresspanel. Settings key on the operationATurn on the machine CPress the item to be setDPressnext page. Next page key to switch to Checking machine operating proceduresBPresspanel. Help key on the operation CPress the item to be displayedPreparing Items for Embroidering Checking the needle Needle precautionsPreparing the Needle DLower the presser foot lever Replacing the needleBobbin precautions Winding/Installing the BobbinWinding the bobbin This model Other modelUse the embroidery bobbin thread for embroidering Start/stop button lights up in orangeMake sure that the thread passes under the pretension disk Bobbin winding will stop LPress Start/stop button onceStart/stop button immediately to stop the bobbin winding When the thread became tangled under the bobbin winder seat Install the bobbin wound with thread Installing the bobbinActual size This modelBe careful not to drop the bobbin Bobbin cover opensBe sure to insert the bobbin correctly Cutter cuts the thread Reattach the bobbin cover Information about the spools of thread is described below Upper ThreadingAbout the spool of thread Embroidery foot is raised Threading the upper threadATurn on the machine BRaise the presser foot lever Hand as shown below Thread take-up lever Upper threading is finished Such a case, start from m againGetting Ready Material to the fabric Preparing the FabricAttaching a stabilizer Embroidery frame medium Setting the fabric in the embroidery frameEmbroidery frame small option Embroidery frame large optionMedium Option Embroidery sheet large option Embroidery sheetFor details, refer to BPlace the embroidery sheet on the inner frameAbobbin and set it into the bobbin case Attaching the Embroidery FrameAttaching the embroidery frame ARaise the presser foot lever Removing the embroidery frameEmbroidery Embroidery pattern types Selecting Embroidery PatternsCopyright information † Setting the display while embroidering Setting for embroideringLCD button Example Selecting alphanumeric characters Specify the characters for embroidery Selecting alphanumeric charactersExample Selecting an embroidery pattern Select the pattern Selecting an embroidery patternAPress Selecting a frame pattern Using an embroidery cardSelect the frame shape Select the stitchOperation is the same as in Selecting an embroidery pattern CTurn on the machine DPress On the screenESelect a pattern Embroidering a pattern EmbroideringPrepareon the screen.embroidery thread of the color shown c BSet the embroidery thread, and thread the needleHPress Start/stop button again EPress Start/stop buttonPress Thread cutter button once Needle is raised and the threads are cutKRemove the upper thread AppliquéingMCut the excess thread ASelect an appliqué patternPosition for the appliqué is stitched, and the machine stops Editing and Saving Patterns Adjusting the layout and the sizeChange position keys Size keyLayout key Rotation keyAdjusting the upper thread tension Bobbin thread is too tight Adjusting the bobbin thread tensionBobbin thread is too loose Bobbin thread appears slightly on the right side of fabricEnter DEF and press Press KPress to turn it to Connecting character patternsStitching starting point is set to lower left of the design APressmachine. Start/stop button to stop ResewingStopping while embroidering Thread runs out partway through a designASet the upper thread or bobbin thread Press Forward one stitch increases the stitch numberETurn off the machine Always remove the embroidery unit when you move the machineFTurnpattern.on the machine, and then select KRestart the embroideryEmbroidery data precautions Using the Memory FunctionPrecautions on Using the Computer to Create and Save Data Tajima .dst Embroidery DataSaving patterns Switch screens using Previous page keySelected pattern is shown in reverse highlighting CPressRetrieving embroidery patterns from the computer GAdjust the pattern as desired, and then begin embroidering Switch screens usingESelect the pattern you wish to retrieve FPressAppendix Cleaning the machine surface Care and MaintenanceCleaning the race FRemove the bobbin caseDo not apply oil to the bobbin case Attaching the Embroidery Foot This section describes how to attach the embroidery foot QAttaching the embroidery foot DHold the embroidery foot Q with your right hand, as shownSet the embroidery foot perpendicular Correctly install the needle TroubleshootingBurr on it Service center Area around the hole Embroidery foot is scratched, orBobbin-winding thread guide Correctly Remove the tangled thread. IfOn it Thread is tangledThread tension is incorrect Correctly install the needle Thread tension is incorrectBobbin thread Needle is bent or blunt Replace the needle SkippedNo pattern selected Select a pattern Be sure to rethread the machine. If you press Error messagesPressing Retrieve key Error Message Probable CauseEmbroidery key was pressed when the embroidery unit is not When the embroidery unit is attachedRefer to An Embroidery Memory Card that may not compatible with yourOperation beep Adjusting the LCDThen start the procedure again from step When the following screen appears, upgrading is completedUpgrading Your Machines Software Following screen appearsAir vent Index10, 31 Page 885-V51 English XE5427-001