Brother CS 8060 manual Thread cassette is raised

Page 26

GETTING READY ———————————————————————————————————————————————————

3Push the thread cassette eject lever on the left side of the machine toward the back.

1

1Thread cassette eject lever

XThe thread cassette is raised.

•If the sewing machine is turned off, the thread cassette will not be ejected correctly.

4Remove the thread cassette.

5Pull the cover of the thread cassette out toward you, and then pull off the spool cap that is inserted onto the spool pin.

1

2

3

1Spool cap (orange)

2 Spool pin

3 Cover

6Place the spool for the upper thread onto the spool pin.

Slide the spool onto the spool pin so that the thread unwinds from the left, as seen from the top.

1

1Spool

7Slide the spool cap onto the spool pin. With the rounded side of the spool cap positioned toward the top, slide the spool cap onto the spool pin as far as possible until the down side of the spool touches the down end of the spool pin.

•Only the orange spool cap should be placed on the spool pin in the thread cassette.

CAUTION

●If the spool or the spool cap is not positioned correctly, the thread may become tangled around the spool pin or the needle may break.

CONTENTS GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX

INDEX

20

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Page Enclosed Accessories AccessoriesNames of Machine Parts and Their Functions Front viewNeedle and presser foot section Right-side/rear view Getting ReadyContents Getting Ready Operation buttonsOperation panel StitchesOptional Accessories Following are available as optional accessoriesSewing Machine Features IntroductionContents Sewing Adjusting the Thread TensionAdjusting the Stitch Width and Length Useful Sewing TipsTroubleshooting Stitch SettingsMaintenance Error messagesImportant Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Congratulations on Choosing OUR Machine Getting Ready Power supply precautions Turning the Machine On/OffTurning on the machine 3Unplug the power supply cord from the electrical outlet4Unplug the power supply cord from the power supply jack Turning off the machineWinding the bobbin Winding/Installing the BobbinBobbin precautions Move the bobbin thread spool pin up as far as possibleWinding/Installing the Bobbin Thread is cut to a suitable length Thread guide for bobbin winding Two slitsBPress start/stop button once Sewing machine stopsInstalling the bobbin Slide the bobbin cover latch to the right7Reattach the bobbin cover Spools that can be loaded into the thread cassette Upper ThreadingAbout the spool of thread Spools that cannot be loaded into the thread cassetteLoading the spool into the thread cassette Upper ThreadingThread cassette is raised Place the spool for the upper thread onto the spool pinFollow arrow 2 indicated on the thread cassette Follow arrow 5 indicated on the thread cassetteSpool of thread is now loaded in the thread cassette Check that the thread cassette indicator is lit up in greenThreading the needle Upper threading is finished 1Placepin. the spool of thread onto the extra spool Using the extra spool pin5Close the thread cassette compartment cover For more details, refer to About the spool of threadRemove the needle Extra spool pin is now installed3Install a needle Refer to Replacing the needleUsing the twin needle For details, refer to Replacing the needleInstall the twin needle For details, refer to Thread the needle manuallyGetting Ready Insert the bobbin into the shuttle Refer to steps 1 through 5 of Installing the bobbinPulling up the bobbin thread Needle types and their uses Needle precautionsReplacing the Needle FabricsIncorrect needle Checking the needleCorrect needle Replacing the needle Install the twin needle in the same way 3Using the screwdriver, loosen the needle clamp screwNeedle can be removed from the needle bar Needle is installed4Lower the needle-changing tool 8Lowerneedle.the needle-changing tool offReplacing the presser foot Presser foot precautionsReplacing the Presser Foot Presser foot holder releases the presser foot Presser foot is attachedFor details, refer to Replacing the presser foot Removing the presser foot holderRemoving the presser foot holder 1Remove the presser foot 2Turn off the sewing machine Using the optional walking footAttaching the walking foot 1Remove the presser foot holder 5Attach the presser foot holder For details, refer to Removing the presser foot holderFree-arm sewing Then,position.install the flap back to its originalSewing Cylindrical Pieces Slide the flap off to the leftSewing Basics Sewing General sewing procedure 3Place the fabric under the presser foot Positioning the fabricTurn on the sewing machine Fabric is now positioned to be sewnStarting to sew Machine stops sewing with the needle lowered in the fabric Machine stops sewing Securing the stitchingFor details, refer to Starting to sew Machine starts sewing Machine starts sewing in the normal sewing directionRelease the start/stop button or foot controller Sewing reinforcement stitches2Raise the presser foot lever When you have finished sewing, cut the threadsCutting the thread Threads are cut and the needle is raisedCorrect thread tension Adjusting the Thread TensionChanging the tension of the upper thread Upper thread is too tightStitch width adjustment indicator lights up Adjusting the Stitch Width and LengthAdjusting the stitch width Changing the needle positionAdjusting the stitch length Stitch length adjustment indicator lights upChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing thick fabrics Sewing an even seam allowance Sewing thin fabricsSewing stretch fabrics Aligning the fabric with the presser footSewing Basics Utility Stitches Selecting stitching When the machine is first turned on, 00 will be displayedSelecting Stitching Attach the presser footSelecting Stitching Stitch Sewing overcasting stitches using overcasting foot GOvercasting Stitches Attach overcasting foot GReverse stitching Sewing overcasting stitches using zigzag foot JPreventing fraying center baseline Stretch fabricsSewing overcasting stitches using the optional side cutter Contents Getting Ready Sewing9sewing 8Position the fabric in the side cutterLower the presser foot lever, and then start Basic stitching When sewing is finished, cut the threadBasic Stitching Position3Attach blind hem foot R Sew a blind hem according to the following procedureBlind Hem Stitching 4Select a stitchIf the needle catches too much of the hem fold Buttonhole Stitching ButtonholeButtonhole sewing 3Attach buttonhole foot a If the button does not fit in the button guide plateSize of the buttonhole is set Pullpossible.down the buttonhole lever as far asFor details, refer to Adjusting the stitch width Changing the stitch widthTrim off any excess of the gimp thread Button sewingSewing buttonholes on stretch fabrics Feed dogs are lowered9Start Aftersewing.sewing for about 10 seconds at low 4Place the button into button-sewing foot M5Select stitch Zipper can be sewn in place Zipper InsertionInserting a centered zipper Are described below7Topstitch around the zipper Inserting a side zipper6Select stitch 7Select stitch Wrong side of fabric Mm 1/8 inchBTopstitch around the zipper Elastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching 3Select stitch Sew the elastic tape to the fabric whileAppliqué, Patchwork and Quilt Stitching Quilting4Attach zigzag foot J Appliqué stitchingRemove the thick paper after pressing the seam allowance Piecing Edge of the fabric, and sew using stitchPatchwork crazy quilt stitching Baste the fabric to be quilted Attach the walking foot For details, refer to Using the optional walking footQuilting Walking foot Presser foot holder Using the optional quilting guideFree-motion quilting 1Removeholder. the presser foot and the presser footNormally, the drop feed lever is positioned at the left 4Slide the drop feed lever, located at the rear7After sewing is finished, slide the drop feed Bar tack stitching Reinforcement StitchingTriple stretch stitching 5Pullpossible.down the buttonhole lever as far as Attach monogramming foot N 3Adjust the stitch width to select the desired eyelet sizeEyelet Stitching Decorative Stitching Decorative4Select stitch Fagoting3Attach zigzag foot J Set the stitch width to 7.0 mm 1/4 inch4Trim along the stitches Scallop stitchingSmocking 3Sew parallel stitching at intervals of 1 cm 3/8 inchJoining 3Select stitch , orHeirloom stitching 4Sew along the center of the unfrayed section Utility Stitches Stitch Settings Maintenance AppendixStitch Settings Utility stitchesStitch Settings Stitch Width Stitch Length Mm inch Utility Stitches Cleaning the shuttle MaintenanceCleaning the machine surface Needle plate cover is removedDo not apply oil to the shuttle Remove the shuttleGrasp the shuttle, and then pull it out Loosen the upper thread tension TroubleshootingPresser foot lever is raised Lower the presser foot lever There are knots or tangles Clean the shuttle Bobbin designed specifically forCorrectly install the presser foot Needle is bent or blunt Replace the needleStitch is not Needle was not raised Press the needle position button.Red Green ShuttleSewing lamp is damaged Contact your retailer or the nearest Fabric doesNot feed Error messages Operation beepChanging the needle stop position Needle stop position changes to the raised positionIndex NumericsIndex English

CS 8060 specifications

The Brother CS 8060 is a versatile and user-friendly sewing machine designed to cater to both beginners and experienced sewists. This robust and reliable model stands out in the market due to its combination of modern technology, versatility, and range of features, making it an excellent choice for various sewing projects.

One of the main features of the Brother CS 8060 is its comprehensive array of built-in stitches. With over 60 stitch options available, including utility, decorative, and quilting stitches, users can easily find the perfect stitch for their project. The machine also offers an automatic one-step buttonholer, which simplifies the process of creating buttonholes. This functionality eliminates the guesswork typically associated with buttonhole creation, ensuring consistent and professional results.

The Brother CS 8060 is equipped with a user-friendly LCD display that makes navigating through stitch options and settings intuitive. This digital interface provides clear information on selected stitches, including a visual representation, and allows users to adjust stitch length and width easily. Additionally, the machine supports automatic needle threading, a feature that saves time and minimizes frustration for users.

Another highlight of the Brother CS 8060 is its lightweight and portable design, making it ideal for taking to sewing classes or crafting gatherings. This sewing machine boasts a built-in handle, ensuring easy transportation without compromising stability during operation. Furthermore, the free arm design facilitates sewing hems and cuffs, making it easier to work on smaller projects or tricky areas of fabric.

The Brother CS 8060 also features a drop-in bobbin system, allowing for quick and straightforward bobbin changes. The transparent cover allows users to monitor thread levels easily. This machine supports various fabric types, from lightweight materials like silk and cotton to heavier fabrics like denim and canvas, making it a perfect choice for all sewing enthusiasts.

In summary, the Brother CS 8060 is an exceptional sewing machine that combines numerous features and advanced technologies, making it suitable for a wide range of sewing tasks. Its built-in stitches, user-friendly interface, portability, and adaptability to different fabric types make it a reliable choice for anyone looking to enhance their sewing experience. Whether you are crafting garments, home decor, or quilting projects, the Brother CS 8060 provides the tools necessary to achieve beautiful results effortlessly.
Top Page Image Contents