aSlide the sewing speed controller to the right (so that the speed will be fast).
1
1Sewing speed controller
bPress
(start/stop button) once.
1
1Start/stop button
XThe bobbin starts spinning and the thread is wound around the bobbin.
XThe bobbin spins slowly when it is full.
cWhen the bobbin begins spinning slowly,
press
(start/stop button) once.
X The sewing machine stops.
dUse scissors to cut the end of the thread wound around the bobbin.
eSlide the bobbin winder shaft to the left.
fRemove the bobbin from the shaft.
gRemove the spool cap and spool.
hSwing down the bobbin thread spool pin, close the bobbin winder cover, and then slide the sewing speed controller back to its original position.
Memo
●When the sewing machine is started or the balance wheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.
CONTENTS GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX
INDEX
Winding/Installing the Bobbin 15
Page
Accessories
Enclosed Accessories
Front view
Names of Machine Parts and Their Functions
Getting Ready
Needle and presser foot section Right-side/rear view
Operation buttons
Contents Getting Ready
Stitches
Operation panel
Following are available as optional accessories
Optional Accessories
Introduction
Sewing Machine Features
Contents
Adjusting the Stitch Width and Length
Adjusting the Thread Tension
Sewing
Useful Sewing Tips
Maintenance
Stitch Settings
Troubleshooting
Error messages
Important Safety Instructions
For Users in the UK, EIRE, Malta and Cyprus only
Congratulations on Choosing OUR Machine
Getting Ready
Turning the Machine On/Off
Power supply precautions
4Unplug the power supply cord from the power supply jack
3Unplug the power supply cord from the electrical outlet
Turning on the machine
Turning off the machine
Bobbin precautions
Winding/Installing the Bobbin
Winding the bobbin
Move the bobbin thread spool pin up as far as possible
Winding/Installing the Bobbin
Thread guide for bobbin winding Two slits
Thread is cut to a suitable length
Sewing machine stops
BPress start/stop button once
Slide the bobbin cover latch to the right
Installing the bobbin
7Reattach the bobbin cover
About the spool of thread
Upper Threading
Spools that can be loaded into the thread cassette
Spools that cannot be loaded into the thread cassette
Upper Threading
Loading the spool into the thread cassette
Place the spool for the upper thread onto the spool pin
Thread cassette is raised
Follow arrow 5 indicated on the thread cassette
Follow arrow 2 indicated on the thread cassette
Check that the thread cassette indicator is lit up in green
Threading the needle
Spool of thread is now loaded in the thread cassette
Upper threading is finished
5Close the thread cassette compartment cover
Using the extra spool pin
1Placepin. the spool of thread onto the extra spool
For more details, refer to About the spool of thread
3Install a needle
Extra spool pin is now installed
Remove the needle
Refer to Replacing the needle
For details, refer to Replacing the needle
Using the twin needle
For details, refer to Thread the needle manually
Install the twin needle
Getting Ready
Refer to steps 1 through 5 of Installing the bobbin
Pulling up the bobbin thread
Insert the bobbin into the shuttle
Replacing the Needle
Needle precautions
Needle types and their uses
Fabrics
Checking the needle
Correct needle
Incorrect needle
Replacing the needle
3Using the screwdriver, loosen the needle clamp screw
Install the twin needle in the same way
4Lower the needle-changing tool
Needle is installed
Needle can be removed from the needle bar
8Lowerneedle.the needle-changing tool off
Presser foot precautions
Replacing the Presser Foot
Replacing the presser foot
Presser foot is attached
Presser foot holder releases the presser foot
Removing the presser foot holder
Removing the presser foot holder 1Remove the presser foot
For details, refer to Replacing the presser foot
Using the optional walking foot
Attaching the walking foot 1Remove the presser foot holder
2Turn off the sewing machine
For details, refer to Removing the presser foot holder
5Attach the presser foot holder
Sewing Cylindrical Pieces
Then,position.install the flap back to its original
Free-arm sewing
Slide the flap off to the left
Sewing Basics
Sewing
General sewing procedure
Turn on the sewing machine
Positioning the fabric
3Place the fabric under the presser foot
Fabric is now positioned to be sewn
Starting to sew
Machine stops sewing with the needle lowered in the fabric
For details, refer to Starting to sew Machine starts sewing
Securing the stitching
Machine stops sewing
Machine starts sewing in the normal sewing direction
Sewing reinforcement stitches
Release the start/stop button or foot controller
Cutting the thread
When you have finished sewing, cut the threads
2Raise the presser foot lever
Threads are cut and the needle is raised
Changing the tension of the upper thread
Adjusting the Thread Tension
Correct thread tension
Upper thread is too tight
Adjusting the stitch width
Adjusting the Stitch Width and Length
Stitch width adjustment indicator lights up
Changing the needle position
Stitch length adjustment indicator lights up
Adjusting the stitch length
Trial sewing
Useful Sewing Tips
Changing the sewing direction
Sewing curves
Sewing thick fabrics
Sewing stretch fabrics
Sewing thin fabrics
Sewing an even seam allowance
Aligning the fabric with the presser foot
Sewing Basics
Utility Stitches
Selecting Stitching
When the machine is first turned on, 00 will be displayed
Selecting stitching
Attach the presser foot
Selecting Stitching
Overcasting Stitches
Sewing overcasting stitches using overcasting foot G
Stitch
Attach overcasting foot G
Preventing fraying center baseline
Sewing overcasting stitches using zigzag foot J
Reverse stitching
Stretch fabrics
Contents Getting Ready Sewing
Sewing overcasting stitches using the optional side cutter
8Position the fabric in the side cutter
Lower the presser foot lever, and then start
9sewing
Basic Stitching
When sewing is finished, cut the thread
Basic stitching
Position
Blind Hem Stitching
Sew a blind hem according to the following procedure
3Attach blind hem foot R
4Select a stitch
If the needle catches too much of the hem fold
Buttonhole
Buttonhole Stitching
Buttonhole sewing
Size of the buttonhole is set
If the button does not fit in the button guide plate
3Attach buttonhole foot a
Pullpossible.down the buttonhole lever as far as
Changing the stitch width
For details, refer to Adjusting the stitch width
Sewing buttonholes on stretch fabrics
Button sewing
Trim off any excess of the gimp thread
Feed dogs are lowered
4Place the button into button-sewing foot M
5Select stitch
9Start Aftersewing.sewing for about 10 seconds at low
Inserting a centered zipper
Zipper Insertion
Zipper can be sewn in place
Are described below
Inserting a side zipper
6Select stitch
7Topstitch around the zipper
Wrong side of fabric Mm 1/8 inch
7Select stitch
BTopstitch around the zipper
Sewing Stretch Fabrics and Elastic Tape
Stretch stitching
Elastic attaching
Sew the elastic tape to the fabric while
3Select stitch
Quilting
Appliqué, Patchwork and Quilt Stitching
Appliqué stitching
Remove the thick paper after pressing the seam allowance
4Attach zigzag foot J
Edge of the fabric, and sew using stitch
Patchwork crazy quilt stitching
Piecing
For details, refer to Using the optional walking foot
Quilting
Baste the fabric to be quilted Attach the walking foot
Free-motion quilting
Using the optional quilting guide
Walking foot Presser foot holder
1Removeholder. the presser foot and the presser foot
4Slide the drop feed lever, located at the rear
7After sewing is finished, slide the drop feed
Normally, the drop feed lever is positioned at the left
Reinforcement Stitching
Triple stretch stitching
Bar tack stitching
5Pullpossible.down the buttonhole lever as far as
3Adjust the stitch width to select the desired eyelet size
Eyelet Stitching
Attach monogramming foot N
Decorative
Decorative Stitching
3Attach zigzag foot J
Fagoting
4Select stitch
Set the stitch width to 7.0 mm 1/4 inch
Smocking
Scallop stitching
4Trim along the stitches
3Sew parallel stitching at intervals of 1 cm 3/8 inch
3Select stitch , or
Joining
Heirloom stitching
4Sew along the center of the unfrayed section
Utility Stitches
Appendix
Stitch Settings Maintenance
Utility stitches
Stitch Settings
Stitch Settings
Stitch Width Stitch Length Mm inch
Utility Stitches
Cleaning the machine surface
Maintenance
Cleaning the shuttle
Needle plate cover is removed
Remove the shuttle
Grasp the shuttle, and then pull it out
Do not apply oil to the shuttle
Troubleshooting
Presser foot lever is raised Lower the presser foot lever
Loosen the upper thread tension
Correctly install the presser foot
Clean the shuttle Bobbin designed specifically for
There are knots or tangles
Needle is bent or blunt Replace the needle
Red Green
Needle was not raised Press the needle position button.
Stitch is not
Shuttle
Fabric does
Not feed
Sewing lamp is damaged Contact your retailer or the nearest
Operation beep
Error messages
Needle stop position changes to the raised position
Changing the needle stop position
Numerics
Index
Index
English