Brother 885-V67 operation manual Be careful not to drop the removed screws in the machine

Page 100

APPENDIX ——————————————————————————————————————————————————————————————————————————————————————————————————————————

jUse the enclosed disc-shaped screwdriver to loosen the two screws on the needle plate.

Note

●Be careful not to drop the removed screws in the machine.

kSlightly lift up the needle plate, cut any tangled threads, and then remove the needle plate.

Remove the fabric and threads from the needle plate.

If the fabric cannot be removed, even after completing these steps, contact your nearest authorized service center.

lRemove any threads in the race and around the feed dogs.

mTurn the handwheel to raise the feed dogs.

nAlign the two screw holes in the needle plate with the two holes at the needle plate mounting base, and then fit the needle plate onto the machine.

oLightly finger-tighten the screw on the right side of the needle plate. Then, use the disc- shaped screwdriver to firmly tighten the screw on the left side. Finally, firmly tighten the screw on the right side.

Turn the handwheel to check that the feed dogs move smoothly and do not contact the edges of the slots in the needle plate.

aCorrect position of feed dogs

bIncorrect position of feed dogs

Note

●Be careful not to drop the removed screws in the machine.

98

Image 100

Contents Sewing Machine Product CodePage Important Safety Instructions Electrical HazardsFor a longer service life For repair or adjustment This machine is intended for household useContents 106 107Included accessories AccessoriesAbout zigzag foot J Optional accessories Accessory compartmentNames of Machine Parts and Their Functions Main partsOperation buttons Needle and presser foot sectionButtons provided on some models Keys and indicators provided on some models Operation panelSpool pin Storing the spool capInstalling the spool pin Storing the spool pinHole on the back of the machine, as Shown.1 BPushplace.the spool pin down until it locks intoUsing Your Sewing Machine Power supply precautionsPower supply Sewing light comes on when the machine is turned onFoot controller Changing the needle stop positionNeedle stop position changes to the raised position Aright to select the desired sewing speedChanging the initial needle position Cancelling the operation beepMachine is now set so that it will not beep Threading the Machine Winding the bobbinSpool pin swings up BRemove the spool capDSlide the spool cap onto the spool pin KTrim the excess thread above the bobbin Make sure that the thread passes under the pre-tension diskPull 1 cm 3/8 inch of thread from the hole on the bobbin For models equipped with the fast bobbin winding system Thread is cut to a suitable length Lower threading Actual size 11.5 mm 7/16 inch This modelFor models equipped with the quick-set bobbin Then, pull the thread toward you to cut it with the cutter c Upper threading Remove the spool cap GSlide the spool cap onto the spool pinThread take-up lever Needle bar thread guide DFully lower the needle threader lever Catch the thread on the hook as shown belowDrawing up the lower thread For models equipped with the quick-set bobbinLightly hold the end of the upper thread Bobbin cover should still be removedNeedle precautions Replacing the NeedleNeedle types and their uses DenimChecking the needle Replacing the needleBall point needle Transparent nylon threadInstall the twin needle in the same way CLower the presser foot leverInstallthread.the thread spool and thread the upper Sewing with the twin needleThread the upper thread for the left needle For details, refer to steps a through l of Upper threadingTwo lines of stitching are sewn parallel to each other HAttach zigzag foot JModels equipped with a needle threader Turn on the sewing machine Select a stitchReplacing the Presser Foot Replacing the presser footReplace the presser foot as described below Mark on the wheel points up. With modelsRemoving the presser foot holder Presser foot is attachedAttaching the presser foot holder Remove the presser footFollow the basic procedures below to sew General sewing procedureSewing Ifwidth.necessary, adjust the stitch length Selecting a stitchStitch is selected DAttach the presser foot indicated in the LCDAdjusting the stitch length and width Starting to sew Machine starts sewingOn the wheel points up. With models equipped BRaise the presser foot leverMachine stops sewing Raise the presser foot leverSewing reinforcement stitches Each otherThread tension Correct tensionUpper tension is too tight Upper tension is too looseUseful Sewing Tips Trial sewingChanging the sewing direction Sewing curvesSewing hook-and-loop Fastener Presser foot remains level, allowing the fabric to be fedSewing thin fabrics Sewing stretch fabricsStitching cylindrical pieces Slide the flat bed attachment to the left to release itUsing zigzag foot Overcasting StitchesAttach zigzag foot J Select a stitch CSew with the edge of the fabricUsing overcasting foot Attach overcasting foot G Select stitch orWhen sewing is finished, cut the thread Basic StitchingBasic stitching Changing the needle positionBlind HEM Stitching Reverse the skirt or pantsFold back the fabric inside along the basting Stitch widthThick fabric Normal fabric If the needle does not catch the hem foldButtonholes can be sewn and buttons can be sewn on Buttonhole SewingAuto Rfc. Automatic Reinforcement Size of the buttonhole is set Once sewing is completed, Raiseposition.the buttonhole lever to its originalSewing buttonholes on stretch fabrics Trim off any excess of the gimp threadButton sewing Feed dogs are loweredAfter sewing for about 10 seconds at low Normally, the feed dog position lever is Positioned atZipper Insertion Refer to Basic stitching onFSelect stitch Sew the stitching in order, from a to cSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching BAttach zigzag foot J CSelect a stitchUtility Stitches APPLIQUÉ, Patchwork and Quilt Stitching 7/32 1/16Appliqués Patchwork crazy quilt stitchingPiecing Remove the basting, if necessaryQuilting For a seam allowance on the left sideDSelect stitch SewingUsing the optional quilting guide Free-motion quilting† Walking foot † Presser foot holder ARemoveholder. the presser foot and the presser footPattern Reinforcement Stitching Triple stretch stitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Fagoting Scallop stitching SmockingDTrim along the stitches CSew parallel stitching at intervals of 10 mm 3/8 inchShell tuck stitching JoiningFold the fabric along the bias BAttach zigzag foot J Unfold the fabric, and then iron the tucks down to one sideHeirloom stitching Characters can be sewn by following the procedure below Selecting charactersFollowing display is shown on Attach the presser foot indicated on the LCDCombining characters Repeat steps band c to add M No and E NoAftersewing.checking the entered characters, start Adding new characters after sewingChecking characters Deleting charactersLast character will be deleted Making a new combination of characters after sewingSewing the character stitches Stitch is sewn in the direction indicated by the arrowSelect a character stitch Attach monogramming foot NCharacters 1 changes to Select No for making adjustmentsCombine the character stitches 034 No + No + No Display returns to the normal character stitching mode Sew the characters 034 againStitch Settings Utility stitchesSatin scallop Auto Rfc.Automatic Reinforcement 1/4 3/32 1/4 1/64 Select a stitch width of 5.0 mm 3/16 inch or less Mirror image stitches Stitch WidthHemming, heirloom Walking Foot Reverse Rev Reinforcement Rfc. Stitching Stitch Type Maintenance Cleaning the racePrecautions on storing the machine Cleaning the machine surfaceRemove the bobbin case Grasp the bobbin case, and then pull it outDo not put oil on the race Align the S and z marksNeedle plate cover Frequent troubleshooting topics TroubleshootingUpper thread tightened up Symptom For details, refer to Cleaning the race onTangled thread on wrong side of fabric Cause Incorrect upper threadingHFeed the upper thread as shown in the illustration below Thread take-up lever Symptoms † SymptomIncorrect thread tension Cause/remedy/check detailsDRemoveholder. the presser foot and presser foot Fabric is caught in the machine and cannot be removedIf threads remain in the bobbin case, remove them Be careful not to drop the removed screws in the machine Memo 100 Checking machine operationsTurn on the machine Select middle needle position stitch Correctly thread the machineList of symptoms 101102 103 Is tangled orFabric is Wrinkled104 105 Operation beep Error Messages106 Numerics Index107 108 Page English 885-V67 XF3961-1011