Brother 885-V67 operation manual 100, Checking machine operations, Correctly thread the machine

Page 102

APPENDIX ——————————————————————————————————————————————————————————————————————————————————————————————————————————

■Checking machine operations

If the needle plate has been removed, check machine operations to confirm that installation has been completed correctly.

aTurn on the machine.

bSelect (middle needle position stitch).

Note

●Do not yet install the presser foot and thread.

cSlowly turn the handwheel toward you (counterclockwise), and look from all sides to check that the needle falls at the center of the hole in the needle plate.

If the needle contacts the needle plate, remove the needle plate, and then install it again, starting with step m in “Removing the fabric from the machine” (page 98).

aHole in the needle plate

bHandwheel

dSelect zigzag stitch . At this time, increase

the stitch length and width to their maximum settings.

•For details on changing the settings, refer to “Adjusting the stitch length and width” (page 38).

eSlowly turn the handwheel toward you (counterclockwise) and check that the needle bar and feed dogs operate correctly.

If the needle or feed dogs contact the needle plate, the machine may be malfunctioning; therefore, contact your nearest authorized service center.

fTurn off the machine, and then install the bobbin and presser foot.

•Refer to “Lower threading” (page 20) and “Replacing the presser foot” (page 34).

gCorrectly thread the machine.

•For details on threading the machine, refer to “Upper threading” (page 23).

Note

●The thread may have become tangled as a result of incorrect upper threading. Make sure that the machine is correctly threaded.

hPerform trial sewing with normal fabric.

Note

●Incorrect sewing may be the result of incorrect upper threading or sewing thin fabrics. If there are poor results from the trial sewing, check the upper threading or the type of fabric being used.

100

Image 102

Contents Sewing Machine Product CodePage Important Safety Instructions Electrical HazardsFor a longer service life For repair or adjustment This machine is intended for household useContents 106 107Accessories Included accessoriesAbout zigzag foot J Optional accessories Accessory compartmentNames of Machine Parts and Their Functions Main partsNeedle and presser foot section Operation buttonsButtons provided on some models Spool pin Keys and indicators provided on some modelsOperation panel Storing the spool capHole on the back of the machine, as Shown.1 Installing the spool pinStoring the spool pin BPushplace.the spool pin down until it locks intoPower supply Using Your Sewing MachinePower supply precautions Sewing light comes on when the machine is turned onNeedle stop position changes to the raised position Foot controllerChanging the needle stop position Aright to select the desired sewing speedCancelling the operation beep Changing the initial needle positionMachine is now set so that it will not beep Spool pin swings up Threading the MachineWinding the bobbin BRemove the spool capDSlide the spool cap onto the spool pin Make sure that the thread passes under the pre-tension disk KTrim the excess thread above the bobbinPull 1 cm 3/8 inch of thread from the hole on the bobbin For models equipped with the fast bobbin winding system Thread is cut to a suitable length Lower threading Actual size 11.5 mm 7/16 inch This modelFor models equipped with the quick-set bobbin Then, pull the thread toward you to cut it with the cutter c Upper threading Remove the spool cap GSlide the spool cap onto the spool pinThread take-up lever Needle bar thread guide DFully lower the needle threader lever Catch the thread on the hook as shown belowLightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Bobbin cover should still be removedNeedle types and their uses Needle precautionsReplacing the Needle DenimBall point needle Checking the needleReplacing the needle Transparent nylon threadInstall the twin needle in the same way CLower the presser foot leverThread the upper thread for the left needle Installthread.the thread spool and thread the upperSewing with the twin needle For details, refer to steps a through l of Upper threadingModels equipped with a needle threader Two lines of stitching are sewn parallel to each otherHAttach zigzag foot J Turn on the sewing machine Select a stitchReplace the presser foot as described below Replacing the Presser FootReplacing the presser foot Mark on the wheel points up. With modelsAttaching the presser foot holder Removing the presser foot holderPresser foot is attached Remove the presser footGeneral sewing procedure Follow the basic procedures below to sewSewing Stitch is selected Ifwidth.necessary, adjust the stitch lengthSelecting a stitch DAttach the presser foot indicated in the LCDAdjusting the stitch length and width On the wheel points up. With models equipped Starting to sewMachine starts sewing BRaise the presser foot leverSewing reinforcement stitches Machine stops sewingRaise the presser foot lever Each otherUpper tension is too tight Thread tensionCorrect tension Upper tension is too looseChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing hook-and-loop Fastener Presser foot remains level, allowing the fabric to be fedStitching cylindrical pieces Sewing thin fabricsSewing stretch fabrics Slide the flat bed attachment to the left to release itAttach zigzag foot J Select a stitch Using zigzag footOvercasting Stitches CSew with the edge of the fabricUsing overcasting foot Attach overcasting foot G Select stitch orBasic stitching When sewing is finished, cut the threadBasic Stitching Changing the needle positionBlind HEM Stitching Reverse the skirt or pantsFold back the fabric inside along the basting Stitch widthThick fabric Normal fabric If the needle does not catch the hem foldButtonhole Sewing Buttonholes can be sewn and buttons can be sewn onAuto Rfc. Automatic Reinforcement Size of the buttonhole is set Once sewing is completed, Raiseposition.the buttonhole lever to its originalSewing buttonholes on stretch fabrics Trim off any excess of the gimp threadButton sewing Feed dogs are loweredAfter sewing for about 10 seconds at low Normally, the feed dog position lever is Positioned atZipper Insertion Refer to Basic stitching onFSelect stitch Sew the stitching in order, from a to cElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching BAttach zigzag foot J CSelect a stitchUtility Stitches APPLIQUÉ, Patchwork and Quilt Stitching 7/32 1/16Piecing AppliquésPatchwork crazy quilt stitching Remove the basting, if necessaryDSelect stitch QuiltingFor a seam allowance on the left side Sewing† Walking foot † Presser foot holder Using the optional quilting guideFree-motion quilting ARemoveholder. the presser foot and the presser footPattern Bar tack stitching Reinforcement StitchingTriple stretch stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Fagoting DTrim along the stitches Scallop stitchingSmocking CSew parallel stitching at intervals of 10 mm 3/8 inchFold the fabric along the bias BAttach zigzag foot J Shell tuck stitchingJoining Unfold the fabric, and then iron the tucks down to one sideHeirloom stitching Following display is shown on Characters can be sewn by following the procedure belowSelecting characters Attach the presser foot indicated on the LCDAftersewing.checking the entered characters, start Combining charactersRepeat steps band c to add M No and E No Adding new characters after sewingLast character will be deleted Checking charactersDeleting characters Making a new combination of characters after sewingSelect a character stitch Sewing the character stitchesStitch is sewn in the direction indicated by the arrow Attach monogramming foot NSelect No for making adjustments Characters 1 changes toCombine the character stitches 034 No + No + No Display returns to the normal character stitching mode Sew the characters 034 againStitch Settings Utility stitchesSatin scallop Auto Rfc.Automatic Reinforcement 1/4 3/32 1/4 1/64 Select a stitch width of 5.0 mm 3/16 inch or less Mirror image stitches Stitch WidthHemming, heirloom Walking Foot Reverse Rev Reinforcement Rfc. Stitching Stitch Type Precautions on storing the machine MaintenanceCleaning the race Cleaning the machine surfaceDo not put oil on the race Remove the bobbin caseGrasp the bobbin case, and then pull it out Align the S and z marksNeedle plate cover Troubleshooting Frequent troubleshooting topicsUpper thread tightened up Tangled thread on wrong side of fabric SymptomFor details, refer to Cleaning the race on Cause Incorrect upper threadingHFeed the upper thread as shown in the illustration below Thread take-up lever Incorrect thread tension Symptoms† Symptom Cause/remedy/check detailsFabric is caught in the machine and cannot be removed DRemoveholder. the presser foot and presser footIf threads remain in the bobbin case, remove them Be careful not to drop the removed screws in the machine Memo Turn on the machine Select middle needle position stitch 100Checking machine operations Correctly thread the machineList of symptoms 101102 Fabric is 103Is tangled or Wrinkled104 105 Error Messages Operation beep106 Index Numerics107 108 Page English 885-V67 XF3961-1011