Brother 885-V67 operation manual Shell tuck stitching, Joining

Page 73

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

Shell tuck stitching

The gathers that look like shells are called “shell tucks”. They are used to decorate trims, the front of blouses or cuffs made of thin fabrics.

aFold the fabric along the bias.

bAttach zigzag foot “J”.

cSelecttension.stitch , and then increase the thread

•For details, refer to “Selecting a stitch” (page 37).

dSew while making sure that the needle drops slightly off the edge of the fabric.

1

aNeedle drop point

eUnfold the fabric, and then iron the tucks down to one side.

Joining

Decorative bridging stitches can be sewn over the seam allowance of joined fabrics. This is used when making a crazy quilt.

aAttach zigzag foot “J”.

bSew together the right sides of the two pieces of fabric, and then open up the seam allowances.

2

1 3

1

3

aWrong side of fabric

b6.5 mm (1/4 inch) seam allowance

cStraight stitch

cSelect stitch , or .

dTurn the fabric over so that the right side faces up, and then sew over the seam with the center of the presser foot aligned with the seam.

aRight side of fabric

71

Image 73

Contents Product Code Sewing MachinePage Electrical Hazards Important Safety InstructionsFor a longer service life This machine is intended for household use For repair or adjustmentContents 107 106Included accessories AccessoriesAbout zigzag foot J Accessory compartment Optional accessoriesMain parts Names of Machine Parts and Their FunctionsOperation buttons Needle and presser foot sectionButtons provided on some models Operation panel Keys and indicators provided on some modelsSpool pin Storing the spool capStoring the spool pin Installing the spool pinHole on the back of the machine, as Shown.1 BPushplace.the spool pin down until it locks intoPower supply precautions Using Your Sewing MachinePower supply Sewing light comes on when the machine is turned onChanging the needle stop position Foot controllerNeedle stop position changes to the raised position Aright to select the desired sewing speedChanging the initial needle position Cancelling the operation beepMachine is now set so that it will not beep Winding the bobbin Threading the MachineSpool pin swings up BRemove the spool capDSlide the spool cap onto the spool pin KTrim the excess thread above the bobbin Make sure that the thread passes under the pre-tension diskPull 1 cm 3/8 inch of thread from the hole on the bobbin For models equipped with the fast bobbin winding system Thread is cut to a suitable length Actual size 11.5 mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Then, pull the thread toward you to cut it with the cutter c Upper threading GSlide the spool cap onto the spool pin Remove the spool capThread take-up lever Needle bar thread guide Catch the thread on the hook as shown below DFully lower the needle threader leverFor models equipped with the quick-set bobbin Drawing up the lower threadLightly hold the end of the upper thread Bobbin cover should still be removedReplacing the Needle Needle precautionsNeedle types and their uses DenimReplacing the needle Checking the needleBall point needle Transparent nylon threadCLower the presser foot lever Install the twin needle in the same waySewing with the twin needle Installthread.the thread spool and thread the upperThread the upper thread for the left needle For details, refer to steps a through l of Upper threadingHAttach zigzag foot J Two lines of stitching are sewn parallel to each otherModels equipped with a needle threader Turn on the sewing machine Select a stitchReplacing the presser foot Replacing the Presser FootReplace the presser foot as described below Mark on the wheel points up. With modelsPresser foot is attached Removing the presser foot holderAttaching the presser foot holder Remove the presser footFollow the basic procedures below to sew General sewing procedureSewing Selecting a stitch Ifwidth.necessary, adjust the stitch lengthStitch is selected DAttach the presser foot indicated in the LCDAdjusting the stitch length and width Machine starts sewing Starting to sewOn the wheel points up. With models equipped BRaise the presser foot leverRaise the presser foot lever Machine stops sewingSewing reinforcement stitches Each otherCorrect tension Thread tensionUpper tension is too tight Upper tension is too looseTrial sewing Useful Sewing TipsChanging the sewing direction Sewing curvesPresser foot remains level, allowing the fabric to be fed Sewing hook-and-loop FastenerSewing stretch fabrics Sewing thin fabricsStitching cylindrical pieces Slide the flat bed attachment to the left to release itOvercasting Stitches Using zigzag footAttach zigzag foot J Select a stitch CSew with the edge of the fabricAttach overcasting foot G Select stitch or Using overcasting footBasic Stitching When sewing is finished, cut the threadBasic stitching Changing the needle positionReverse the skirt or pants Blind HEM StitchingStitch width Fold back the fabric inside along the bastingIf the needle does not catch the hem fold Thick fabric Normal fabricButtonholes can be sewn and buttons can be sewn on Buttonhole SewingAuto Rfc. Automatic Reinforcement Size of the buttonhole is set Raiseposition.the buttonhole lever to its original Once sewing is completed,Trim off any excess of the gimp thread Sewing buttonholes on stretch fabricsFeed dogs are lowered Button sewingNormally, the feed dog position lever is Positioned at After sewing for about 10 seconds at lowRefer to Basic stitching on Zipper InsertionSew the stitching in order, from a to c FSelect stitchStretch stitching Sewing Stretch Fabrics and Elastic TapeElastic attaching BAttach zigzag foot J CSelect a stitchUtility Stitches 7/32 1/16 APPLIQUÉ, Patchwork and Quilt StitchingPatchwork crazy quilt stitching AppliquésPiecing Remove the basting, if necessaryFor a seam allowance on the left side QuiltingDSelect stitch SewingFree-motion quilting Using the optional quilting guide† Walking foot † Presser foot holder ARemoveholder. the presser foot and the presser footPattern Triple stretch stitching Reinforcement StitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingPullpossible.down the buttonhole lever as far as Once sewing is completed, Decorative Stitching Fagoting Smocking Scallop stitchingDTrim along the stitches CSew parallel stitching at intervals of 10 mm 3/8 inchJoining Shell tuck stitchingFold the fabric along the bias BAttach zigzag foot J Unfold the fabric, and then iron the tucks down to one sideHeirloom stitching Selecting characters Characters can be sewn by following the procedure belowFollowing display is shown on Attach the presser foot indicated on the LCDRepeat steps band c to add M No and E No Combining charactersAftersewing.checking the entered characters, start Adding new characters after sewingDeleting characters Checking charactersLast character will be deleted Making a new combination of characters after sewingStitch is sewn in the direction indicated by the arrow Sewing the character stitchesSelect a character stitch Attach monogramming foot NCharacters 1 changes to Select No for making adjustmentsCombine the character stitches 034 No + No + No Sew the characters 034 again Display returns to the normal character stitching modeUtility stitches Stitch SettingsSatin scallop Auto Rfc.Automatic Reinforcement 1/4 3/32 1/4 1/64 Select a stitch width of 5.0 mm 3/16 inch or less Stitch Width Mirror image stitchesHemming, heirloom Walking Foot Reverse Rev Reinforcement Rfc. Stitching Stitch Type Cleaning the race MaintenancePrecautions on storing the machine Cleaning the machine surfaceGrasp the bobbin case, and then pull it out Remove the bobbin caseDo not put oil on the race Align the S and z marksNeedle plate cover Frequent troubleshooting topics TroubleshootingUpper thread tightened up For details, refer to Cleaning the race on SymptomTangled thread on wrong side of fabric Cause Incorrect upper threadingHFeed the upper thread as shown in the illustration below Thread take-up lever † Symptom SymptomsIncorrect thread tension Cause/remedy/check detailsDRemoveholder. the presser foot and presser foot Fabric is caught in the machine and cannot be removedIf threads remain in the bobbin case, remove them Be careful not to drop the removed screws in the machine Memo Checking machine operations 100Turn on the machine Select middle needle position stitch Correctly thread the machine101 List of symptoms102 Is tangled or 103Fabric is Wrinkled104 105 Operation beep Error Messages106 Numerics Index107 108 Page English 885-V67 XF3961-1011