Kenmore 625.38825 owner manual Keeping the Water Softener Clean, Cleaning Nozzle & Venturi

Page 17

[i:ii:ii:ii:_i:i:ii:_i:i:ifSECTION 3 F!i:ii:_i:i:ii:_i:i:ii:_i:] CARE OF YOUR WATER SOFTENER

B. KEEPING THE WATER SOFTENER CLEAN

NOZZLE & VENTURI

A clean nozzle and venturi (FIG. 11) is a must for the softener to work right. This small unit moves brine from the salt storage tank to the resin tank during re-

generation. If it becomes plugged with sand, silt,

dirt, etc., the softener will not work and you will get hard water.

To get to the nozzle and venturi, remove the softener top cover. Be sure the softener is in service cycle (no

water pressure at nozzle and venturi).

1)Turn off the cap from the nozzle and venturi hous- ing.

2)Lift out the screen support and screen, do not lose the large o-ring seal.

3)Then the nozzle and venturi. Wash and rinse the

parts in warm water until clean. If needed, use a small brush to remove iron or dirt. Also check and

clean the gasket, flow plugs and screens.

Carefully replace all parts in the correct order. Lu- bricate the o-ring seal with silicone grease or Vase-

line and place in position. Install and tighten the

cap, by hand only. Do not overtighten and break the cap or housing.

IRON FROM RESIN BED

Your water softener takes hardness minerals (cal-

cium and magnesium) out of the water. It can also

control some "dear water" iron. See maximum al-

lowed in the specifications on page 4-1. With clear water iron, water from a faucet is clear when first put into a glass. After 15 to 30 minutes, the water be- gins to cloud or turn rust colored. A water softener WILL NOT remove any iron which makes the water cloudy or rusty as it comes from the faucet (called red water iron). To take red water iron out of water,

or over the maximum of clear water iron, an iron fil-

Cleaning Nozzle & Venturi

Cap _

O-ring Seal _'-m_.

Screen

Support

_

 

 

 

 

*Flow Plug

Nozzle

Screen

-.................._ _

(1 -EP)

& Venturi

 

 

 

Gasket

_

Screen

 

 

IMPORTANT: Be sure _ holes in the gasket are

feted directly over the small holes in the nozzle & venturi

housing,

*Flow Plug

(HVDC)

Nozzle & Venturi

Housing

*Install with numbered side up concave

side down. Be sure the largest flow plug is located in the nozzle & venturi housing,

ter or other equipment is needed. Your local Sears store has trained people to help you with iron water problems.

If your water supply has clear water iron, even

though less than the maximum allowed, regular

resin bed cleaning is needed. Sears has resin bed cleaner, Item No. 42-34426 for this. Clean the bed at least every 6 months. If iron shows up in the soft wa-

ter before 6 months, clean more often. Printed

instructions are on the resin bed cleaner bottle.

3-2

Page 16 Page 18
Image 17
Page 16 Page 18
Contents UltraSoft 200 Water Softener Sears Residential Water Softener Full ONE Year Warranty on Water SoftenerFull TEN Year Warranty Against Leaks Contents t Safety Guides Plastic Check List of STEP-BY-STEP Guides to InstallSET Present Time DAY Program TimerSET Water Hardness Number Program the TimerHardness Number SET Recharge Regeneration TimeStorage tank Sanitize the Water SoftenerWater Softening Salt with Iron Removing Tank with SaltExtra Recharge Faceplate Timer FeaturesSalt Monitor System Recharge TonightSelect Tions and 12 / 24 Hour ClockWater Flow Through SoftenerI1 Error Code Position IndicatorsI1 Recharge Time Remaining and Valve I1 Program MemorySoftener in Service ServiceRegeneration Softener in FillSoftener Fast Rinse Softener in BackwashWater Flow Electronics SectionAutomatic Bypass Salt Bridge When to Refill with SaltCleaning Nozzle & Venturi Keeping the Water Softener CleanCare of Your Water Softener Problem Cause Correction Checklist ... to Help YOU Save MoneyBypass Valves Timer SR Code SR27Pressure Drop His Possible Defect Code Procedure in transformerManual Initiated Electronics Diagnostics NONI Cycle Flow Rates Gallons PER MIN Manual Advance Regeneration CheckHold Disassembly Rotary Valve ServiceAssembly Lieve PressureBottom distributor Service CycleBackwash Cycle Brining and Brine Rinse CyclesFast Rinse Cycle Iiiiiiiiiiiii Repair Parts for Water Softener Description Water Softener CompleteInlet Outlet Grounding Clamps Part Brine Valve AssemblyValve Assembly KEY Part NO. Number AssemblyBypass Installation Valve Sears

625.38825, 625.3882 specifications

The Kenmore 625.3882 and 625.38825 are two notable models in the Kenmore lineup, designed to meet the needs of modern consumers seeking performance, efficiency, and reliability in their home appliances. These models are particularly celebrated for their advanced features and technologies, making them standout options in their category.

One of the main features of the Kenmore 625.3882 and 625.38825 is their user-friendly interface, which allows for intuitive operation. Both models come equipped with a digital display that provides clear feedback and simplifies the selection process for various settings and functions. This accessibility ensures that users can easily navigate through the appliance’s multiple features with minimal hassle.

A significant highlight of these models is their impressive filtration technology. The Kenmore 625.3882 and 625.38825 utilize advanced HEPA filtration systems, which effectively capture allergens, dust, and particles from the air, ensuring a cleaner living environment. This technology is particularly beneficial for allergy sufferers or anyone looking to improve indoor air quality.

In addition to their filtration capabilities, these models also boast energy-efficient performance. Designed with sustainability in mind, they consume less power without compromising on cleaning efficiency. This aspect not only helps to reduce energy bills but also promotes eco-friendliness, aligning with the growing consumer trend towards environmentally conscious appliances.

Another characteristic that sets the Kenmore 625.3882 and 625.38825 apart is their overall durability. Built with high-quality materials, these models are designed to withstand the rigors of daily use. The construction enhances their longevity, making them a wise investment for homeowners looking for long-lasting performance.

Additionally, both models feature various speed settings and cleaning modes, allowing users to customize their cleaning experience based on specific needs. Whether addressing light dusting or deep cleaning chores, the versatile functionality accommodates a range of cleaning tasks, providing flexibility for users.

In summary, the Kenmore 625.3882 and 625.38825 are equipped with numerous features that make them reliable choices for homeowners. With their advanced filtration systems, user-friendly design, energy efficiency, and robust construction, these models exemplify the quality and performance that Kenmore is known for. Whether for everyday cleaning or special tasks, these appliances are well-suited to meet the demands of modern living, ensuring satisfaction for years to come.
Top Page Image Contents