Kenmore 625.3882 Manual Advance Regeneration Check, Hold, Cycle Flow Rates Gallons PER MIN

Page 25

[ii:ii:ii:ii: i:ii:ii: i:ii:ii:SECTIONi:i 5 Ii ii:ii: i:ii:ii: i:ii:ii:Si:ii:ii]E RVIC E TEC H. INFO RMATIO N

A.TROUBLESHOOTING

MANUAL ADVANCE REGENERATION CHECK

This check verifies proper operation of the valve

motor, brine tank fill, brine draw, regeneration flow

rates, and other controller functions. Always make

the initial checks, and the manual initiated diag- nostics.

Notes:

The faceplate display must show a steady time (not flashing). If an error code shows, first press the SE-

to enter the diagnostic display.

Press the ON / OFF-HOLD button and hold in for

3 seconds. *RECHARGE and Fill begin to flash

(or clean backwash begins, if set) as the softener

enters the fill cycle of regeneration. When FILL is

on steady, remove the brinewell cover and, using

a flashlight, observe fill water entering the tank. *Note:

If the CLEAN feature is set to ON, a cleaning back- wash (CLEAN and Bkwsh or Rinse flashes in the dis-

play, along with the minutes of the clean cycle re-

maining), precedes the recharge.

a. If water does not enter the tank, look for an ob- structed nozzle, venturi, fill flow plug, brine tubing, or brine valve riser pipe.

Note: If water system pressure is low, an elevated

drain hose may cause back pressure, stopping brine draw.

_1_ Again press ON/OFF-HOLD to move the soft-

ener into backwash. Look for a fast flow of water from the drain hose.

a. An obstructed flow indicates a plugged top dis-

tributor, backwash flow plug, or drain hose.

_

Press ON/OFF-HOLD

to move

the softener

into

 

fast rinse. Again look for a fast drain flow. Allow

 

the softener to rinse for a few minutes to flush out

 

any brine that may remain in the resin tank from

 

the brining

cycle

test.

 

 

_To

return

the softener

to service,

press ON

/ OFF-

 

HOLD.

 

 

 

 

 

 

 

r]

 

BRINE VALVE

 

 

 

 

,

'

FLOAT SETTING

 

 

/. / float stop

CYCLE FLOW RATES (GALLONS PER MIN.)

FILL (flow to salt storage tank)

0.3

(1.1

liters)

BRINING

'}

.16

(.61

liters)

BACKWASH

(flow to drain)

1.8

(6.8

liters)

BRINE

RINSE

l

.12

(.45

liters)

FAST

RINSE

 

1.8

(6.8

liters)

E After observing fill, press the ON/OFF-HOLD button to move the softener into brining. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight

into the brinewell and observing a noticeable drop in the liquid level.

Note:

Be sure a salt bridge is not preventing water with salt contact.

a. If the softener does not draw brine...

...nozzle and/or venturi dirty or defective. See page 3- 2

...nozzle and venturi not seated properly on gasket. See page 3-2

...restricted drain (check drain fitting and hose).

...defective nozzle and venturi seal. See page 3-2

...other inner valve defect (rotor seal, rotor & disc, wave washer, etc.).

float

FREEBOARD MEASUREMENT

Distance from top of resin tank, to top of resin bed.)

t

resin tank

FREEBOARD

7"-11"

5-4

Page 24 Page 26
Image 25
Page 24 Page 26
Contents UltraSoft 200 Water Softener Full TEN Year Warranty Against Leaks Full ONE Year Warranty on Water SoftenerSears Residential Water Softener Contents t Safety Guides Plastic Check List of STEP-BY-STEP Guides to InstallSET Present Time DAY Program TimerSET Water Hardness Number Program the TimerHardness Number SET Recharge Regeneration TimeStorage tank Sanitize the Water SoftenerWater Softening Salt with Iron Removing Tank with SaltExtra Recharge Faceplate Timer FeaturesSalt Monitor System Recharge TonightSelect Tions and 12 / 24 Hour ClockWater Flow Through SoftenerI1 Error Code Position IndicatorsI1 Recharge Time Remaining and Valve I1 Program MemorySoftener in Service ServiceRegeneration Softener in FillWater Flow Softener in BackwashSoftener Fast Rinse Automatic Bypass SectionElectronics Salt Bridge When to Refill with SaltCleaning Nozzle & Venturi Keeping the Water Softener CleanCare of Your Water Softener Problem Cause Correction Checklist ... to Help YOU Save MoneyBypass Valves Timer SR Code SR27Pressure Drop His Manual Initiated Electronics Diagnostics Procedure in transformerPossible Defect Code NONI Hold Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Disassembly Rotary Valve ServiceAssembly Lieve PressureBottom distributor Service CycleBackwash Cycle Brining and Brine Rinse CyclesFast Rinse Cycle Iiiiiiiiiiiii Repair Parts for Water Softener Description Water Softener CompleteInlet Outlet Grounding Clamps Part Brine Valve AssemblyValve Assembly Bypass Installation Valve AssemblyKEY Part NO. Number Sears

625.38825, 625.3882 specifications

The Kenmore 625.3882 and 625.38825 are two notable models in the Kenmore lineup, designed to meet the needs of modern consumers seeking performance, efficiency, and reliability in their home appliances. These models are particularly celebrated for their advanced features and technologies, making them standout options in their category.

One of the main features of the Kenmore 625.3882 and 625.38825 is their user-friendly interface, which allows for intuitive operation. Both models come equipped with a digital display that provides clear feedback and simplifies the selection process for various settings and functions. This accessibility ensures that users can easily navigate through the appliance’s multiple features with minimal hassle.

A significant highlight of these models is their impressive filtration technology. The Kenmore 625.3882 and 625.38825 utilize advanced HEPA filtration systems, which effectively capture allergens, dust, and particles from the air, ensuring a cleaner living environment. This technology is particularly beneficial for allergy sufferers or anyone looking to improve indoor air quality.

In addition to their filtration capabilities, these models also boast energy-efficient performance. Designed with sustainability in mind, they consume less power without compromising on cleaning efficiency. This aspect not only helps to reduce energy bills but also promotes eco-friendliness, aligning with the growing consumer trend towards environmentally conscious appliances.

Another characteristic that sets the Kenmore 625.3882 and 625.38825 apart is their overall durability. Built with high-quality materials, these models are designed to withstand the rigors of daily use. The construction enhances their longevity, making them a wise investment for homeowners looking for long-lasting performance.

Additionally, both models feature various speed settings and cleaning modes, allowing users to customize their cleaning experience based on specific needs. Whether addressing light dusting or deep cleaning chores, the versatile functionality accommodates a range of cleaning tasks, providing flexibility for users.

In summary, the Kenmore 625.3882 and 625.38825 are equipped with numerous features that make them reliable choices for homeowners. With their advanced filtration systems, user-friendly design, energy efficiency, and robust construction, these models exemplify the quality and performance that Kenmore is known for. Whether for everyday cleaning or special tasks, these appliances are well-suited to meet the demands of modern living, ensuring satisfaction for years to come.
Top Page Image Contents