Kenmore 625.3486 Program, Timer, Gpg hardness 2ppmironx5=10+10 Times 30 Hardness Number, Recharoe

SECTION 1

1 C.PROGRAM

2.SET WATER HARDNESS NUMBER:

• Press the SELECT button once to display 25 (flashing) and HARDNESS.

The	grains		per	gallon			(gpg)
hardness		of	your	water		supply
is on	your		water		analysis		re-
port.	Be	sure	to enter		water		test	HARDNESS
results		on	page	2,	for	future

reference.

NOTE:

If your water supply contains iron, compensate for

it by adding to the water hardness number. For example, ass ume your water is 20 gpg hard and con tains 2 ppm iron. Add 5 to the hardness number for each 1

ppm of iron. In this example, you would use 30for your hardness n umber.

20 gpg hardness

2ppmironx5=10+10

(times) 30 HARDNESS NUMBER

•Press the UP / DOWN buttons to set your water

hardness number in the display. The DOWN

button moves the display to 1. The UP button

moves the display to the highest setting (see

maximum setting for your model in the specifica- tions).

NOTE:

Each press of the UP / DOWN button changes the

display by I between I and 25. Between 25 and the

highest number, the display changes 5 at a

time...25, 30, 35, etc. Holding the UP or DOWN

button in changes the display twice each second.

3. SET RECHARGE (REGENERATION) TIME:

• Press the SELECT button to display 2:00 AM

(flashing) and RECHARGE TIME.

At the 2:00 AM recharge						time			q,nnA_
									I_-'UU
setting,	the	softener		begins		re-			RECHAROE
									TIME
generation		(see	pages		12	and
13) at	2:00	AM,	ending		no	later
than	4:00	AM.	This		is	a	good	time	in	most
households		because			water	is	not	being	used	(see

WATER SOFTENER START-UP

THE TIMER

Automatic Bypass, page 14). If a different recharge

time setting would be better for your household, do the following.

•Press the UP / DOWN buttons to set the desired

recharge starting hour. Be sure to observe the

AM-PM as you did when setting the present time of day.

NOTE:

Each press of the UP / DOWN buttons changes the

display i hour. Holding the buttons in changes the

display twice each second.

4. SET CLEAN FEATURE (optional):

• Press the SELECT button to display OFF

(flashing) and CLEAN.

This

feature

is

beneficial

on

nrr

water

supplies

containing

iron

ur

r-

and/or

high

amounts

of

sedi-

CLEAN

ments

(sand,

silt,

dirt,

etc.).

When

set

to

ON,

a

backwash

n I

and

fast

rinse

cycle

will

occur

Ur-

first,

preceeding

the

normal

re-

CLEAN

generation

sequence

(see page

12).

This

provides

extra

clean-

ing of the resin bed before it is

regenerated

with

the

salt

brine.

To

conserve

water,

if your

water

supply

does

not

contain

iron

or

sediments,

be

sure

this feature

is set to

OFF. Use

the

UP

/ Down

buttons

to

change

the

ON

/

OFF

displays.

• Press the SELECT button once again, to return

the present time, and RECHARGE TONIGHT in the display.

5 RECHARGE TO_iGR?

3

2

4WAI_HPLOW

1

IF YOU NEED HELP PROGRAMMING THE TIMER, CALL TOLL FREE, NUMBER

1-800-426-9345.SEE PAGES 10 AND 11 FOR OTHER FACE PLATE TIMER FEATURES.

7