[i!i !! :;:_!! :;:_!i SECTION 2
HOW YOUR WATER SOFTENER WORKS
A. FACEPLATE TIMER FEATURES
OPTIONAL SETTINGS - SALT EFFICIENCY,
CLEAN FEATURE, CLEAN FEATURE MINUTES,
MAXIMUM DAYS BETWEEN REGENERA-
TIONS, 12 / 24 HOUR CLOCK and GALLONS /
LITERS:
1.To set any of the following options, press and hold
SELECT 1 for 3 seconds. Press the SELECT 1 key
and the SALT EFFICIENCY display shows. Use the
UP / Down button to change the ON / OFF dis- plays.
.... 2°_"_ | - | I- | _ ______ | ||
| I_l | I- | r- |
| u |
ically sets to 7 minutes. However, you can adjust
this time from I to 15 minutes in length. To change
this cycle time, use the UP button to increase the time, or the DOWN button to shorten the time. If no
change is desired, continue below.
4.Press SELECT 1 to show the 12 HOUR display.
Continue with next step if no change is desired.
.......... | - | I I_1I |
C | ||
|
| TIME |
_2_ _
[]SALT EFFICIENCY: 0 When this feature is ON, the unit will operate at salt efficiencies of 4000 grains
of hardness per pound of salt or higher. (May re- charge more often using smaller salt dosage and less
water). For installations in the state of California,
you must turn the Salt Efficiency Feature setting to ON.
2.Press SELECT 1 again to show the CLEAN dis- play.
..... | ...... | ||
.... | I_lF | .... | U |
| CLEAN |
| CLEAN |
[]CLEAN: This feature is beneficial on water sup-
plies containing iron and/or high amounts of sedi- ments (sand, silt, dirt, etc.). When set to ON, a back- wash and fast rinse cycle will occur first, preceeding
the normal regeneration sequence (see page
This provides extra cleaning of the resin bed before
it is regenerated with the salt brine. To conserve wa-
ter set this feature OFF if your water supply does
not contain iron or sediments. Default for UltraSoft 425 is OFF, default for UltraSoft 480 is ON.
3.Press SELECT 1 again and the CLEAN TIME dis- play shows.
|
| sALTSSGS_',_ |
....EVEU_VEL | i I | MIN |
CLEAN | TIME | CLEAN TiME |
default minutes | example: time set to 3 minutes |
|
[CLEAN feature minutes: If you are using this fea-
ture the length of the extra backwash cycle automat-
[12 or 24 hour clock: All time displays are shown
in standard clock time (1 to 12 PM; and I to 12 AM) at the 12 hr default setting. If military time displays
are desired, set to 24 hr by pressing the UP button.
5.Press SELECT 1 again to show the GALLONS or LITERS display.
.... SRI_5 |
| i, |
. | 5 |
|
.... | __ _ | LITERS |
GALLONS |
|
|
[]Gallon or Liter readings: Water usage and flow displays are shown in gallons. If you prefer to have the same displays in liters, press the UP button until Liter shows.
6.Press SELECT 1 again to show the RECHARGE display.
8 | DA_ |
| _l | DAy |
|
|
7 |
|
|
|
|
|
|
SaLTSSGNat6 | RECHARGE | S_LT_GNA | RECHARGE | L |
| mple: set to |
5 |
|
|
|
|
| |
|
|
|
| I | 4 | days maxi- |
2 |
|
|
| I | mum | between |
j__ |
|
|
| ii | regenerations | |
default display |
|
|
|
|
|
[]Maximum days between regenerations: The face-
plate timer automatically controls regeneration fre-
quency (see page
operating efficiency, and under most conditions, this feature will be left in its default mode. Howev-
er, modify this feature if you want to force a regen-
eration every set number of days. For example, if
your water supply contains iron and you want the
softener to regenerate at least once every few days to keep the resin bed clean, set the display as typical-
ly shown above. Setting is available from 1 to 15 days by using the UP and DOWN buttons.
7. Press SELECT i to return the present time display.
Problems, Questions? Call 1- 800- 426- 9345 Kenmore Water Line