Kenmore 170, 275 installation manual Before Installing Checks & Tests, Safety Guides

Page 4

S

C

T

N

_JJJJJJJJJJJJJJJJJ

_JJJJ JJJJJJJJJJJ

_JJJJJJJJJJJJJJJ

_JJ_JJJJJJJJJJ

_JJJJJJJJJJJJJJJ

_dJJdJdJd_d_d

_JJJJJJJJJJJJJJJJJ

_JJJJJJJJJJJJJJJJJ

SECTION1BEFORE INSTALLING CHECKS & TESTS

A. SAFETY GUIDES

Read all steps, guides and rules carefully before installing and using your new water softener. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage.

Reading this book will also help you to get all of the benefits from your water softener.

Your water softener will remove hardness minerals

and "clear water" iron* from water, up to the limits

shown on the specifications page in your owner's manual. It will not remove other types of iron, acids, tastes and odors, etc. It will not purify polluted water or make it safe to drink.

Check with your local public works department for plumbing, electric and sanitation codes. You must fol- low their guides as you install your softener. Codes in

the State of Massachusetts require installations by a

licensed plumber. For installation, use plumbing code

248-CMR of the Commonwealth of Massachusetts.

Use only LEAD-FREE SOLDER AND FLUX, as re- quired by federal and state codes, when installing sol- dered copper plumbing.

Protect the softener and piping from freezing. Dam- age from freezing voids the softener warranty. See how to protect from freezing in your owner's manual.

[] CAUTIONS

PLEASE READ AND COMPLY WITH THE FOLLOWING

GUIDES TO PREVENT DAMAGE TO THE SOFTENER

OR OTHER PROPERTY, PERSONAL INJURY, OR POS-

SIBLE FATAL SHOCK.

THIS SOFTENER WORKS ON 24 VOLTS ONLY. BE

SURE TO USE ONLYTHE TRANSFORMER INCLUDED,

AND PLUG IT INTO A NOMINAL 120V, 60 CYCLE

HOUSEHOLD OUTLET THAT IS GROUNDED AND

PROPERLY PROTECTED BY AN OVERCURRENT DE-

VICE SUCH AS A CIRCUIT BREAKER OR FUSE. IF

TRANSFORMER IS REPLACED, USE ONLY THE AU-

THORIZED SERVICE, CLASS II, 24 VOLT, 10 VA

TRANSFORMER.

Unplug the transformer right away if the power cable should become damaged or frayed. Make re-

pairs, or replace the transformer, before plugging back into the power outlet.

Always unplug the softener from electrical power before removing outer valve covers.

*The capacity to reduce clear water iron is substantiated by WQA test data.

1-1

Deluxe Valve

Image 4
Contents Installation Manual Save this ManualIntroduction Plan Your Installation Restart the Water HeaterBefore Installing Checks & Tests Safety GuidesParts Descriptions Unpacking the Water SoftenerSmall Parts Before Installing Checks & Tests Water System TestsWhere to Install the Water Softener HeaterTOOLS, Pipe and FITTINGS, Other Materials Needed Out fittings included with the softener arePipe and FITTINGS, Plan Drawing ElectricalI1UTypical Soldered Copper or PVC in and OUT Pipes to Softener Deluxe Valve ModelsAdaptoric,o? Typical Threaded in and OUT Pipes to SoftenerAssemble INLET-OUTLET ADAPTORS, or Plastic Bypass Valve GO to Inlet and Outlet Threaded AdapOr the Inlet Outlet Threaded GO toInstalling Holding Clips Bypass Valve Turned DownwardInstalling 3 Valve Bypass and Pipes Install 3-VALVE BypassValve Bypass Move Softener Into Place Move the Softener Into PlaceTypical Soldering Connections Connect Valve and Salt Tank Drains Connect the Valve Drain HoseOl Connect Valve and Salt Tank Drains Connect Salt Tank Overflow TU- BingHouse Main Pressure Test / Check for LeaksShutoff Valves To Electrical Power Install Grounding Wire Between Softener in and OUT PipesElectrical Power Outlet for Your Softener Grounding / ConnectInstall Covers Grounding / Connect to Electrical PowerPlug Transformer Connecting Restart Water HeaterWith High Performance valve High Performance Valve Before Installing Checks & Tests Safety Guides Ring Parts Descriptions Small PartsWater System Tests Where to Install the Water Softener TOOLS, Pipe and FITTINGS, Other Materials Needed YO UR HO USE MAI N Water %--------.. Maine Threaded adaptor Install Sears Bypass Valve and / or Assemble INLET-OUTLET ADAPTORS, or Plastic Bypass ValveInstalling Holding Clips Bypass Valve Turned Downward Install 3-VALVE Bypass Locate Water Softener Connect PipesStep by STE P G Uides to Install Connect Valve and Salt Tank Drains= Connect Valve and Salt Tank Drains Connect Salt Tank Overflow TUHouse Main Water Install Grounding Wire Between Softener in and OUT Pipes Cold Water Pipe Grounding Meter Jumper WireInstall Covers Restart the Water Heater