Kenmore 625.348321 Care of Your Softener 3B. Keeping the Water Softener Clean, Coversnote

Page 15

SECTION 3

CARE OF YOUR SOFTENER

3B. KEEPING THE WATER SOFTENER CLEAN

COVERSNOTE:

To keep your new Kenmore water softener looking nice, apply a coat of paste wax and repeat once a year. When dusty, wipe it with a damp cloth to keep it sparkling.

Never use cleaners having ammonia or abra- sives. They may scratch and dull the surface.

NOZZLE AND VENTURI

A clean nozzle and venturi (FIG. 13) is a must for the softener to work right. This small unit moves brine from the salt storage tank to the resin tank during regeneration. If it becomes plugged with sand, silt, dirt, etc., the softener will not work and you will get hard water.

To get to the nozzle and venturi, remove the softener top cover. Be sure the softener is in service cycle (no water pressure at nozzle and venturi), then turn off the cap from the nozzle and venturi housing. DO NOT LOSE THE LARGE O-RING SEAL. Lift out the screen

FIG. 13

Cap

O--ring Seal

Screen Support

Screen

Nozzle & Venturi

Gasket

*Flow Plug

(1--EP)

Screen

support and screen, then the nozzle and venturi. Wash and rinse the parts in warm water until clean. If needed, use a small brush to remove iron or dirt. Also check and clean the gasket, small screen and flow plug.

Carefully replace all parts in the correct order. Lubricate the o-ring seal with silicone grease or Vaseline and place in position. Install and tighten the cap, by hand only. Do not overtigh- ten and break the cap or housing.

NOTE: Be sure holes in the gasket align with the holes at the bottom of the nozzle & venturi housing.

*Flow Plug

(HVDC)

Nozzle & Venturi

Housing

*INSTALL WITH NUMBERED SIDE UP CONCAVE SIDE DOWN.

IRON FROM THE RESIN BED

Your water softener takes hardness minerals (calcium and magnesium) out of the water. Also, it can control some “clear water” iron0see maximum allowed in the specifications on page

21.With clear water iron, water from a faucet is clear when first put into a glass. After 15 to 30 minutes, the water begins to cloud or turn rust colored. A water softener WILL NOT remove any iron which makes the water cloudy or rusty as it comes from the faucet (called red water iron). To take red water iron out of water, or over

the maximum of clear water iron, an iron filter or other equipment is needed. Your local Sears store has trained people to help you with iron water problems.

If your water supply has clear water iron, even though less than the maximum allowed, regular resin bed cleaning is needed. Sears has resin bed cleaner, Stock No. 42-34426 for this. Clean the bed at least every 6 months. If iron shows up in the soft water before 6 months, clean more often. Printed instructions are on the resin bed cleaner bottle.

IF YOU HAVE QUESTIONS ABOUT CLEANING AND MAINTAINING YOUR SOFTENER,

CALL TOLL FREE, NUMBER 1-800-426-9345.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Save this Manual OWNER’S ManualWarranty Full ONE Year Warranty on Water SoftenerFull TEN Year Warranty Against Leaks Softener Start UP Table of ContentsService Tech Information Repair PartsSection Water Softener START-UP Safety GuidesWater Softener START-UP 1B. Check List of ALL STEP-BY-STEP Guides to InstallSET Time of DAY Water Softener START-UP 1C.PROGRAM the TimerSET the Timer See page 9 for Other Timer Controls and FeaturesWater Softener START-UP 1D. Sanitizing the Water Softener Water Softening Salt with Iron RE Water Softener START-UP 1E. Fill the Storage Tank with SaltHOW Your Water Softener Works Face Plate Timer Features Flashing display is to remind you to reset the timer HOW Your Water Softener Works 2A. Face Plate Timer FeaturesRegeneration ServiceWater Flow Through the Softener in Brining and Brine Rinse Automatic Bypass Salt Bridge Please see page 8 for Salt Filling Directions Salt BridgeIron from the Resin BED Care of Your Softener 3B. Keeping the Water Softener CleanCoversnote Nozzle and VenturiSoftener Keep the Softener from FreezingNo Soft Water Problem Cause CorrectionSET Days and Time of REGENERA- TION, or Recharge Other Things to Know 4A. HOW to FINE-TUNE Your SoftenerSET the Fill Cycle Minutes See Instructions for Using the TABLE, Other Things to Know HOW to FINE-TUNE Your SoftenerInches Other Things to Know 4B. DIMENSIONS/SPECIFICATIONSFaceplate Timer Service TECH. Information 5A. Electrical ConnectionsSee Regeneration Table on page 20, and SPECIFICATIONS, Service TECH. Information 5B. Regeneration Cycle TimesService TECH. Information 5C.TROUBLESHOOTING Automatic Electronic DiagnosticsManual Advance Diagnostic Brine Valve Float Setting Freeboard Measurement Section Servicing the Valve Service TECH. Information 5D.ROTARY Valve ServiceDisassembly AssemblyFill Cycle Service CycleBackwash Cycle Brining and Brine Rinse CyclesFast Rinse Cycle Service TECH. Information Sears Water Softener KEY Part Description Number Repair Parts Brine Valve AssemblyValve Assembly Bypass Installation Valve Model no Parts ListSolid State

625.348321 specifications

The Kenmore 625.348321 is a highly regarded model in the realm of water softeners, designed to alleviate the challenges posed by hard water in households. This unit effectively addresses the mineral buildup caused by calcium and magnesium ions, improving water quality and enhancing the longevity of plumbing fixtures, appliances, and laundry.

One of the standout features of the Kenmore 625.348321 is its impressive grain capacity. With a capacity of 31,000 grains, it is well-suited for medium to large households. This ensures that families experience consistent and reliable soft water, preventing the telltale signs of hard water, such as scale buildup and dry skin.

The unit employs a powerful ion exchange technology, a widely recognized method for softening water. The process involves exchanging the hard water minerals for sodium ions, effectively capturing the unwanted hardness and leaving users with soft, palatable water. This not only enhances the efficiency of soaps and detergents but also promotes the health of plumbing systems and appliances by preventing mineral deposits.

An additional feature is its demand-initiated regeneration system. This technology allows the unit to monitor water usage and regenerate only when necessary, which results in reduced salt and water consumption. This energy-efficient approach not only helps lower utility bills but also contributes to a more sustainable household environment.

The Kenmore 625.348321 also boasts user-friendly programming options, enabling homeowners to easily set and adjust preferences for optimal performance. The intuitive interface allows for quick access to diagnostics and system performance, ensuring that users are well-informed about the status of their water softening system.

Moreover, this model is equipped with a large brine tank that can hold a significant amount of salt, minimizing the frequency of refills and simplifying maintenance. With its compact design, the water softener fits seamlessly into various spaces, making it a convenient choice for homes with limited installation areas.

In summary, the Kenmore 625.348321 stands out as an effective water softener, combining advanced technology with user-friendly features. It provides households with the benefits of soft water, ensuring cleaner clothes, softer skin, and extended appliance life—all key advantages for any modern home.
Top Page Image Contents