Harman-Kardon AVR65 manual Code Readout, Programmed Device Functions

Page 34

Programming the Remote

34

4.Press the Device Control Selector

again, and note that the red light will flash twice to confirm the entry before going dark.

5.Try all of the functions on the remote to make certain that the product operates. Keep in mind that many manufacturers use a number of different combinations of codes, and it is a good idea to make certain that that not only the Power control works, but the volume, channel and transport controls, as appropriate. If all functions do not work properly, you may need to Auto-Search for a different code, or enter a code via the Direct Code Entry method.

Code Readout

When the code has been entered using the Auto Search method, it is always a good idea to find out the exact code so that it may be easily reentered if necessary. You may also read the codes to verify which device has been programmed to a specific Control Selector button.

1. Press and hold both the Device Control Selector bfor the type of product to be entered (e.g., VCR, TV) and the Mute button dat the same time. Hold both buttons until the red light under the button stays lit. Note that the next step must take place while the red light is on, and it must begin within 20 seconds after the light illuminates.

2.Press the Night button j. The red light under the Device Control Selector bwill blink in a sequence that corresponds to the three-digit code, with a one-second pause between each digit. Count the number of blinks between each pause to determine the digit of the code. One blink is the number 1, two blinks is the number 2, and so forth. Ten blinks are used to indicate a “0”.

Example: One blink, followed by a one- second pause, followed by six blinks, fol- lowed by a one-second pause, followed by ten blinks indicates that the code has been set to 160.

For future reference enter the Setup Codes for the equipment in your system here:

CD

 

 

TAPE

 

AUX

 

 

SAT

 

 

 

TV

 

 

 

VCR

 

 

CBL

 

 

 

 

 

 

Programmed Device Functions

Once the AVR65’s remote has been pro- grammed for the codes of other devices, press the appropriate Device Control Selector bto change the remote from control over the AVR65 to the additional product. When you press any of the Device Control Selectors, it will briefly flash in red to indicate that you have changed the device being controlled.

When operating a device other than the AVR65, the controls may not correspond exactly to the function printed on the remote or button. Some commands, such as the volume control, are the same as with the AVR65. Other buttons will change their function so that they corre- spond to a secondary label on the remote. For example, the Sleep and Surround Mode selector buttons also function as the Channel Up and Channel Down buttons when operating most TV sets, VCRs or cable boxes. The Channel Up/Down indi- cation is printed directly on the remote. The same is true for standard CD player, cassette deck, VCR and DVD functions, which follow the standard function icons printed on top of the buttons.

For some products, however, the function of a particular button does not follow the command printed on the remote. In order to see which function a button controls, consult the Function List tables printed in this manual. To use those tables, first check the type of device being controlled (e.g., TV, VCR). Next, look at the remote control diagram pictured on the following page. Note that each button has a number on it.

AVR65 120 volt Rev (C) 10/6/98

Image 34
Contents Description and Features IntroductionSafety Information Important Safety InformationTypographic Conventions CleaningUnpacking Moving the UnitFront Panel Controls ÷ õTMon Selector Press this but 33, into the AVR65’s memory Front Panel Information Display T S R Q P ONight Indicator This indicator Rear Panel Connections Edba á¡ c à ߣ¢Surround Connect these terminals to the surround speakers Remote Control Functions Remote Control Functions OFF Audio Equipment Connections Installation and ConnectionsSystem Installation Connect the analog output of a CD player to the CD inputs ¤AC Power Connections Remote Control ExtensionExternal Audio Power Amplifier Connections Speaker’s manufacturerSystem Configuration Speaker PlacementPlug the Power Cable Þto an unswitched AC outlet System SetupUsing the On-Screen Display Speaker Configuration Press the Set button i÷Output Level Adjustment On the front panel to change the display to SÐW SpeakerAdjustment Letters FLwill flash once each secondDelay Settings To set the delay times, follow these stepsMain Information Display U Basic Operation Using the On-Screen DisplayOperation Semi-OSDDuring a listening session you may Source SelectionFull-OSD For private listening, plug the 1/4Surround Mode Selection Surround Mode Chart Digital Audio Playback Dolby DigitalTuner Operation Night ModePCM Audio Playback Tape Recording Preset TuningRecalling Preset Stations Station SelectionProcessor Reset Memory BackupChannel Direct Input Multiroom Operation InstallationMultiroom Setup IR LinkMultiroom Operation Press the Set button i÷to enter the settingOn the rear panel Direct Code Entry Programming the RemoteProgramming the Remote Auto Search MethodCode Readout Programmed Device FunctionsMacro Programming Device Control Selector bforReassigning Device Control Selectors Volume Punch-ThroughPress the Volume Up button z Press either the AVR aor Program into the reassigned buttonTape Function ListNo. Button Name CD Aux DVDReference for Function List Setup Code Tables Manufacturer/Brand Setup Code NumberSetup Code Tables TV Realistic VCR Setup Code Tables VCR Setup Code Tables AUX DVD Cable Troubleshooting Guide Troubleshooting GuideTechnical Specifications AVR65 120 volt Rev C 10/6/98 AVR AVR65 Table of Contents AVR65 Audio/Video ReceiverStaple or clip original invoice here