Operations, Cues, Troubleshooting, Specifications

your CD. Turning the wheel in a clockwise direction scans forward while a counter-clockwise turn scans the track in reverse. Scan speed increases as the wheel is turned.

11.SEARCH DIAL: The SEARCH DIAL (8) has two func- tions. Use the SEARCH DIAL (8) to make fine adjust- ments in pause mode. Use the SEARCH DIAL (8) to bend the pitch for precise synchronization in play mode.

12. SEARCH: The SEARCH (20) buttons are used to move forward or reverse while in play or pause mode, SEARCH (20) can also be used to find a CUE POINT. Hold down either button for ultra fast searching.

13.STOP: The STOP (14) button ends CD play.

14.SINGLE: Pressing the SINGLE (15) activates the AUTO CUE function. The AUTO CUE function causes the unit to pause at the beginning of music of the following track and allows you to start play immediately from the start of music without any blank space (which exists at the beginning of every track). Pressing the SINGLE (15) but- ton a second time activates the CONTINUOUS function causing the unit to play continuously (after the last track, the unit will return to the first track of the disc and contin- ue to play). Pressing the SINGLE (15) button a third time deactivates the CONTINUOUS function.

15.TIME/OUTRO: The TIME BUTTON (13) switches the time display between the 4 available choices listed under DISPLAY (10). This also switches on/off the Outro func- tion, which only plays the last 30 seconds of each track.

16.PITCH: Pushing the PITCH BUTTON (16) activates the PITCH CONTROL SLIDE (17). The pitch of the CD will change according to the position of the PITCH CON- TROL SLIDE (17).

17. PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (18) will automatically raise the pitch up to +16% or lower the pitch down to -16% from the existing pitch setting. Releasing the buttons will return the pitch to the original pitch setting. You can use this function to match the pitch bend when mixing from one song to another.

18.PITCH CONTROL SLIDE: Moving the PITCH CON- TROL SLIDE (17) up or down will lower or raise the pitch

percentage.

OPERATIONS:

1.Press the OPEN/CLOSE (9) button, place a CD in the DISC TRAY (6) and press the OPEN/CLOSE (9) button again. The tray will close into the unit.

2.Push the TRACK SKIP(12) buttons to select the track you want to play.

3.Press the PLAY/PAUSE (21) buttons and the unit will instantly play.

CUES:

1.To program a cue point (the spot on a CD at which you want play to start) select a track and push PLAY/PAUSE

(21)so the unit enters the PLAY mode. (PLAY/PAUSE LED glows green).

2.When the CD reaches the approximate musical spot you wish to make your cue, push PLAY/PAUSE (21) so the unit enters the PAUSE mode (PLAY/PAUSE LED blinks and the unit will enter stutter mode). Move the SEARCH DIAL (8) forward or in reverse until you reach the precise frame is located, at which point you will want the CD to begin play. Push CUE (22). The cue point is now pro- grammed, the blue LED will remain on. Press and hold

CUE (22) to preview the cue point. Release CUE (22) to return to the cue point. Press CUE (22) to return to this pre-programmed cue point to play at any time.

NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER AGAIN ONCE YOU HAVE SKIPPED TO ANOTHER TRACK. THE CUE WILL BE PRESET TO THE BEGINNING OF THE SELECTED TRACK. PRESS THE CUE BUTTON AND YOU WILL BEGIN AT THE BEGINNING OF YOUR SELECTED TRACK. START YOUR CUE PROGRAMMING SEQUENCE OVER AGAIN.

3.To fine tune your pre-programmed cue point, push the CUE (22) button and the CD will return to the cue point you programmed in step #2. Push PLAY/PAUSE (21) so the unit enters the PAUSE mode at that point. Use the SEARCH DIAL (8) to move forward or backward to find- the proper Cue point. Repeat step #2. If you decide this cue or starting point is okay, leave the unit alone until you are ready to play.

4.If, however, the selected spot is not exactly where you want it, push the CUE (22) button while the CD is playing and the disc will return to the preprogrammed cue point. Repeat step #1 - #3.

NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT (TO HELP YOU FIND THE BEAT). THE STUTTERING EFFECT WILL END WHEN YOU PRESS THE PLAY/PAUSE (21) TO SAVE THE CUE POINT.

TROUBLESHOOTING:

·If the disk will not play, check to see if the disc was loaded correctly (label side up). Also check the disc for excessive dirt, scratches, etc.

·If the disc turns but there is no sound, check the cable connections. If they are okay, check your amplifier or receiver.

·If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many CDs are recorded out of spec and will skip on most or all CD play- ers. Before sending the unit in for repair, try playing a CD that you are sure plays properly.

SPECIFICATIONS:

GENERAL:


Type		Compact Disc Player
Disc Type	Standard Compact discs (12 cm & 8 cm)
Time Display...	Track Elapsed, Track Remain, or Total remain
Variable Pitch		± 16% Slider with Resume Switch
Pitch Bend		± 16% Maximum
Instant Start		Within 0.03 seconds
Track Selection		1 to 99 Tracks
Installation		19" each
Dimensions		19” x 3.5” x 10”
Weight (total)		10.21 lbs. (6.21 Kg)
AUDIO SECTION:
Quantization	1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate		8 Times
Sampling Frequency		44.1 kHz
Frequency Response		20 Hz to 20 kHz
Digital Output		IEC958
Total Harmonic Distortion		Less Than 0.05%
Signal to Noise Ratio		85 dB
Dynamic Range		85 dB
Channel Separation		85 dB
Output Level		2.0 +/- 0.2V R.M.S.
Power Supply		AC 115/230V, 60/50 Hz

SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITH- OUT NOTICE FOR PURPOSE OF IMPROVEMENT.

(5)