Moen 9300 manual Lavatory Waste Installation Instructions, III. Vandal Proof

Page 3

INSTALLATION INSTRUCTIONS

1

6

9

2

6

4

 

 

 

5

7

3

Before installing new faucet make sure that the cartridge nuts are in place. The cartridge and cartridge nuts were properly installed and tested before leaving the factory. Although it is unlikely, it is nevertheless possible that through the handling of the valve by any number of persons the cartridge nuts may not be properly installed. This should be carefully checked at time of installation. If the cartridge nuts are not properly installed, water pressure could force the cartridge out of the casting. Personal injury or water damage to the premises could result.

1.Insert head of spout bolt (6) into the slot at the back of the valve body (7). With the ears of the mounting bracket (5) facing up, screw in the spout tube (9) with the longer unthreaded end up. Mounting bracket (5) should be approximately 1/2" up from spout tube (9). A 7/32" hex wrench is supplied. Lubricate both spout tube o-rings (A) with silicone grease supplied, position the mounting bracket over spout bolt and insert spout tube into valve body.

2.Apply plumber’s putty (not supplied) to bottom of top mounting washers (4). Center washers over holes in deck. Slide valve assembly from under the deck up through sink/deck holes, washers. Insert retaining clips (3) into lower grooves on valve assembly. Release valve assembly down until it rests on top of the washers. Place the 7/32" hex key wrench into the tube bolt (6) and tighten mounting bracket securely.

A

1

2

13

15

3

4

5

7

6

15

12

 

 

1

Drain Plug Base Part

13

Plumbers Putty

 

 

 

 

2

Seat

14

Pivot Rod

 

 

 

 

3

Bottom Gasket

15

Teflon Tape

 

 

 

10

4

Mounting Washer

 

 

 

 

 

 

 

5

Mounting Nut

 

 

 

 

 

 

 

6

Drain Body

4

 

4

 

 

 

 

7

Pivot Rod Seat

 

 

 

 

9

 

 

 

 

 

 

8

Pivot Nut

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

Lift Rod Strap

 

 

 

 

 

 

11

10

Lift Rod Strap Screw

 

 

 

 

(b)

8

 

11

Spring Clip

 

18

(a)

18

14

 

 

 

12

Tailpiece

 

 

 

 

 

 

 

 

 

 

 

 

B

1

2

13

 

12

3

 

4

 

5

 

6

 

9

 

7

 

1

Drain Plug Base Part

13

Plumbers Putty

 

 

2

Seat

14

Pivot Rod

 

 

 

3

Bottom Gasket

 

 

 

 

 

4

Mounting Washer

 

 

 

 

10

5

Mounting Nut

 

 

 

 

 

6

Tail Piece

4

 

4

 

 

7

Pivot Rod Seat

 

 

 

 

 

 

 

8

8

Pivot Nut

 

 

 

 

9

Lift Rod Strap

 

 

 

 

 

10

Lift Rod Strap Screw

 

 

 

 

11

11

Spring Clip

18

(a)

18

(b)

14

12

Seal

 

 

 

 

 

 

 

 

 

 

A. Lavatory Waste Installation Instructions

1)Thoroughly clean around drain opening of lavatory sink.

2)Apply plumbers putty under seat

(2).

3)Thread mounting nut (5), mounting washer (4) and bottom gasket (3) onto drain body (6). Wrap top threaded end of drain body with Teflon tape (15).

4)Position drain body up through drain opening and screw seat onto drain body.

5)Align drain body so that pivot rod opening faces the rear of the sink and tighten the mounting nut snug.

6)Apply Teflon tape to the threaded end of the tailpiece (12) and screw into the drain body. Tighten firmly by hand.

7)Drop in plug base (1) and install pivot rod in one of the following ways:

I.Vandal proof: Prevent unauthorized removal of drain plug. Place pivot rod seat (7) into

opening of drain body as shown. Place the pivot rod (14) into the opening and position the pivot rod through the upper hole of the pop-up base as shown in installation (a). Slide the pivot nut onto the pivot rod and thread snugly onto the drain body, be careful not to over tighten.

II.Easy removal: After inserting drain plug into waste tube, turn drain plug 90 degrees. For quick removal of drain plug for cleaning, follow the instructions above except position parts as shown in illustration (b) above. Do not insert pivot rod into opening of pop-up base.

8)Connect the pivot rod (14) to lift rod strap using spring clip (11) as shown above.

To disassemble waste assembly, reverse steps as listed above. In order to remove seat cover, use screwdriver to bend snap features back from the inside as shown in picture. Do not try to lift seat cover with tool from the outside.

B. Lavatory Waste Installation Instruction

1)Thoroughly clean around drain opening of lavatory sink.

2)Apply plumbers putty under seat

(2).

3)Drop seat into the drain opening in sink.

4)From underneath the sink. Slide bottom gasket (3), mounting washer (4) and mounting nut (5) onto drain seat and hand tighten.

5)Fit seal (12) inside the drain tailpiece (6).

6)Install the tailpiece and hand tighten. Align the entire assembly so that the pivot rod is facing the rear of the sink, hand tighten the mounting nut (5) until snug.

7)Drop in plug base (1) and install pivot rod in one of the following ways:

III. Vandal

proof:

Prevent

unauthorized removal

of drain

plug. Place pivot rod seat (2) into

opening of drain body as shown.

Place the pivot rod (14) into the

opening

and position

the pivot

rod through the upper hole of the pop-up base as shown in installation (a). Slide the pivot nut onto the pivot rod and thread snugly onto the drain body, be careful not to over tighten.

IV. Easy removal: For quick removal of drain plug for cleaning, follow the instructions above except position parts as shown in illustration (b) above. Do not insert pivot rod into opening of pop-up base.

8)Connect the pivot rod (14) to lift rod strap using spring clip (11) as shown above.

To disassemble waste assembly, reverse steps as listed above. In order to remove seat cover, use screwdriver to bend snap features back from the inside as shown in picture below. Do not try to lift seat cover with tool from the outside.

2

Image 3
Contents English Español Helpful Tools Herramientas Utiles Outils UtilesEnglish Français Español Parts Diagram Diágrama DE Piezas Tableau DES PiècesIII. Vandal Proof Installation InstructionsLavatory Waste Installation Instructions Lavatory Waste Installation InstructionHelpline Moen Lifetime Limited Warranty Consumer Information18 a 18 b Instrucciones Para LA InstalacionLineas Telefonicas DE Servicio Moen Garantia Limitada DE Vida Informacion AL ConsumidorDirectives d’installation de la bonde de lavabo Directives D’INSTALLATIONAppeler Sans Frais Notre Service À LA Clientèle

9300 specifications

The Moen 9300 is an innovative kitchen faucet that combines style, functionality, and cutting-edge technology to elevate your culinary experience. Known for its sleek design and robust features, this model is a popular choice for homeowners seeking a perfect blend of aesthetics and convenience.

One of the standout features of the Moen 9300 is its pull-down sprayer. This sprayer offers the flexibility needed for various tasks, from rinsing dishes to filling large pots. The hose extends easily and retracts smoothly, thanks to the Reflex system, which ensures that the sprayer returns to its original position seamlessly after use. This thoughtful design element enhances usability while adding a modern touch to the kitchen.

The Moen 9300 is equipped with the Power Clean technology, which delivers a concentrated spray for superior cleaning performance. This feature is particularly useful for tackling tough messes, making it easier to rinse off stubborn food residue from dishes and surfaces. The high arc of the spout provides ample clearance for filling pots and cleaning bulky items, enhancing the faucet’s overall functionality.

Another notable characteristic of the Moen 9300 is its easy installation process. The faucet is designed with a Duralast cartridge that offers smooth operation and longevity. Its one-handle design not only contributes to a streamlined look but also makes it easy to control the water temperature and flow with precision.

Durability is a key selling point for the Moen 9300, as it is constructed from high-quality materials with a corrosion-resistant finish that ensures it looks great even after years of use. The faucet is also designed with a spot-resistant finish, which helps maintain its pristine appearance by minimizing water spots and fingerprints.

In terms of water efficiency, the Moen 9300 is optimized to meet contemporary standards, incorporating leading technologies that help conserve water without sacrificing performance. This makes it an eco-friendly choice for the environmentally conscious consumer.

Overall, the Moen 9300 is a multifunctional kitchen faucet that stands out for its innovative features and user-friendly design. With its combination of aesthetic appeal, practical functionality, and advanced technology, it is a solid choice for any modern kitchen. Whether you're preparing a gourmet meal or simply washing up, this faucet is designed to make your tasks easier and more enjoyable.