Gemini CDJ-15X manual Operating Instructions, CUE Instructions, Trouble Shooting, Specifications

OPERATING INSTRUCTIONS:

1.Make sure that the VOLTAGE SELECTOR SLIDE (3), found on the rear panel, is set for the proper voltage. Plug the unit in and press the POWER (2) switch.

2.Press the OPEN (16) button, place a CD in the DISC TRAY (10) and close the tray door. The display will initially show the number of tracks and the total time of the CD.

3.Push the TRACK SKIP (6) buttons to select the track you want to play.

4.Press the PLAY/PAUSE (9) button and the unit will instantly play.

CUE INSTRUCTIONS:

1.To start the play at a point other than the beginning of a track, follow these instructions:

First choose the track you wish to play, and then press PLAY/PAUSE

(9) so the unit goes into the play mode. Press PLAY/PAUSE (9) to pause play at the spot where you want the play to start the CUE POINT. Use the SEARCH BUTTONS (7) to pick the precise spot you want play to begin, then press PLAY/PAUSE (9) again to save the cue point. Press the CUE (8) button to pause play at the cue point (the unit will go into the pause mode and the location indicated on the display will be the memorized cue point). You can preview the cue point by pressing and holding down CUE (8). Press PLAY/PAUSE (9) to begin play from the cue point.

NOTE: AFTER A CUE POINT IS SET, PRESSING THE TRACK SKIP (6) BUTTONS CLEARS THE CUE POINT. WHEN YOU PRESS THE CUE (8) BUTTON IN THE NEW TRACK, THE BEGINNING OF THAT TRACK WILL BE THE NEW CUE POINT.

2.Once you have saved a cue point you can fine tune or change the memorized cue point:

To change a cue point, push PLAY/PAUSE (9) so the unit plays from the cue point, then press PLAY/PAUSE (9) at the spot you wish your new cue point to be. Press PLAY/PAUSE (9) again to save the cue point. The unit will go into the pause mode and the location indicated on the display will be the new memorized cue point.

To fine tune a cue point, pause play at the memorized cue point, then use the SEARCH (7) buttons to scan frame by frame (1/75th of a second) to where you want play to begin. Press PLAY/PAUSE (9) to save the new cue point.

NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT (TO HELP YOU FIND THE BEAT). THE STUTTERING EFFECT WILL END WHEN YOU PRESS PLAY/PAUSE (9) TO SAVE THE CUE POINT. ALSO, DURING FINE TUNING IF YOU HOLD DOWN THE SEARCH (7)

BUTTON, THE UNIT WILL SCAN QUICKLY AFTER 10 FRAMES.

TROUBLE SHOOTING:

•If the disk will not play, check to see if the disc was loaded correctly (label side up). Also check the disc for excessive dirt, scratches, etc.

•If the disc turns but there is no sound, check the cable connections. If they are okay, check your amplifier or receiver.

•If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many CDs are recorded out of spec and will skip on most or all CD players. Before sending the unit in for repair, try playing a CD that you are sure plays properly.

SPECIFICATIONS:

GENERAL:
Disc Type	Standard Compact discs (12 cm & 8 cm)
Time Display	Track Elapsed, Track Remain, or Total remain
Variable Pitch	± 16% Slider with Resume Switch
Start	Within 0.03 seconds
Track Selection	1 to 99 Tracks
AUDIO SECTION:
Quantization	1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate	8 Times
Sampling Frequency	44.1 kHz
Frequency Response	20 Hz to 20 kHz
Total Harmonic Distortion	Less Than 0.005%
Signal to Noise Ratio	>96 dB
Dynamic Range	>94 dB
Output Level (nominal)	1.9 Volts R.M.S.
Power Supply	AC 120/230V, 60/50 Hz
Dimensions	8.38” x 8.86” x 3.75” (213 x 225 x 95 mm)
Weight	4.5 lbs. (2 kg)

SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.

(5)