Craftsman 139.53335SRT3, 139.53834SRT3 Tighten the Chain & Cable, Trolley before adjusting chain

Page 11

Assembly Step 5

I

 

Tighten the Chain & Cable

 

Lock

Outer Nut Washer Inner Nut

•Spin the inner nut and lock washer down the threaded shaft, away from the trolley.

___z:__T°:z:zTighten Outer Nut _

•To tighten the chain, turn outer nut in the direction shown. As you turn the nut, keep the chain from twisting.

•When the chain is approximately 1/2" above the base of the T-rail at its midpoint, re-tighten the inner nut to secure the adjustment.

Sprocket noise can result if chain is either too loose or too tight.

When installation is complete, you may notice some chain droop with the door closed. This is normal. If the chain returns to the position shown when the door is open, do not re-adjust the chain.

NOTE: During future maintenance, ALWAYS pull the emergency release handle to disconnect

I_n_r NUt

e__

_

To Tighten

Troll

Chain

II II II I! It II fl II II II

1/2 Inch

I

Base of T-rail

trolley before adjusting chain.

You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section:

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of severe injury or death to persons:

1.READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2.Install only on a properly balanced and lubricated garage door. An improperly balanced door may not reverse and could result in severe injury or death. Repairs to cables, spring assemblies and other hardware must be made by a professional service person before installing opener.

3.Disable all locks and remove all ropes connected to the garage door before installing the opener. Ropes connected to a garage door can cause entanglement and death.

4.It possible, install door opener 7 feet or more above floor with the emergency release handle mounted 6 feet above the floor.

5.Do not connect the opener to power source until instructed to do so.

6.Locate the Door Control within sight of the door at a minimum height of 5 feet where small children cannot reach and away from all moving parts of the door.

7.Install the User Safety Instruction Label on the wall adjacent to the door control and the Maintenance Instruction Label in a prominent location on the inside of the garage door.

8.Upon completion of the installation, the door must reverse when it comes in contact with a one-inch high object or a 2x4 laid flat on the floor.

9.Do not wear watches, rings or loose clothing while installing or servicing an opener. Jewelry or loose clothing can be caught in the mechanism of the garage door or the opener.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Craftsman Start by reviewing these important safety alert symbols YoullNeed Tools Closed Position Sectional Door InstallationOne-Piece Door With Track ONE-PIECE Door Installation One-PieceDoor Without TrackTO your Installation Carton Inventory Wit w edT oHardware Installation HardwareSafety Reversing Sensor Installation Hardware Shown Actual Size Assembly Section Pages 8Assemble the T-rail & Attach Cable Pulley Bracket Operation,noiseand/or RightWrongFasten Raft to Opener Install the Trolley on the T-railHardware Shown Actual SizeMasterFigure Assembly StepInstall the Chain/Cable Attach the Sprocket Cover Tighten the Chain & Cable Trolley before adjusting chainIll AbovethedoorIF1 --L--Ji One-piece door without track Pivot hardware One-piece door without track Jamb hardwareFasten the Header Bracket to the Ceiling Install the Header BracketFasten the Header Bracket to the Wall Attach the T-rail to the Header Bracket Sectional Door & ONE-PIECE Door with Track Position the OpenerHang the Opener L!LIIllllllllltllllllllllll Install the Door ControlDo not connect to live electrical wiring. Connect Door Control Button Fasten securely with 6ABx1-1/2 screwsAttach the Emergency Release Rope and Handle Install the Light and the Lens32 explains how to use the door control RightWrong Permanent Wiring ConnectionsElectrical Requirements Facing the door from inside the garage Safety Reversing SystemAlternate Wall Mount Install the Safety Reversing SensorRight sides of the door Finger tighten the lock nuts Shown Actual SizeTrouble Shooting Fasten Door Bracket IIIIIII!!11111!111II!!l!ll!!!lLllllllllllllllI!l!l!l Alternative Connect Door Arm to TrolleySEC!ONA DoorS Oniy Hole AlignmentAssemble the Door Arm Adjustment Procedures for One-PieceDoorsOpen Door Adjustment Decrease UP limit Closed Door Adjustment Decrease Down limitPages 28 Adjustment Section Adjustment StepTo Adjust the Limits Adjust the UP and Down LimitsTest the Down close force Adjust the ForceHow and When to Adjust the ForcesMust reverse on striking the obstruction Adjustment StepTest The Safety Reversing Sensor Test the Safety Reverse SystemSchedule MaintenanceTo reduce the risk of severe injury or death to persons Care of Your OpenerLockout position Operation of Your Opener53000SRT Series Garage Door Openers Receiver and Remote Control ProgrammingSituation Having a Problem?Probable Cause and Solution Probable Cause & Solution Having a Problem?Installation Parts Repair PartsWie \Fr Opener Assembly PartsAccessories Index Product Type Part Number Model Number Part Description For the repair or replacement parts you needFor in-home major brand repair service Give the following information

139.53648SRT2, 139.53645SRT3, 139.53834SRT3, 139.53335SRT3, 139.53646SRT2 specifications

The Craftsman 139.53660SRT1, 139.53646SRT2, 139.53335SRT3, 139.53834SRT3, and 139.53645SRT3 are a series of advanced garage door openers designed for homeowners looking to enhance convenience, security, and functionality in their daily lives. Each model is equipped with cutting-edge technologies that streamline garage access while ensuring safety and durability.

One of the standout features across these models is the use of a powerful motor system, providing reliable performance for heavy garage doors. The motor's horsepower rating varies across the models, but all ensure consistent lifting strength and rapid opening and closing speeds, catering to different door weights and sizes.

In terms of security, these Craftsman models incorporate advanced encryption technologies, making unauthorized access nearly impossible. The security features include rolling code technology, which changes the access code each time the remote is used, thus preventing cloning and ensuring that only authorized users can operate the door.

These openers also prioritize ease of use. With their compatible smartphone app integration, users can remotely control and monitor their garage doors. Whether they are at home or away, users can receive notifications, check the status of their doors, and even open or close them at the touch of a button, adding an extra layer of convenience.

The installation process is also user-friendly, with many of these models featuring an easy-to-follow instruction manual. Homeowners can typically complete the installation themselves, saving time and money compared to hiring a professional. The durable construction of these openers ensures that they withstand the test of time, with many units equipped with weather-resistant materials that protect against rust and corrosion.

In addition to their functional features, the aesthetic designs of the Craftsman series are noteworthy. They fit seamlessly into a variety of garage styles, with a sleek finish that enhances overall garage appeal.

Overall, the Craftsman 139.53660SRT1, 139.53646SRT2, 139.53335SRT3, 139.53834SRT3, and 139.53645SRT3 garage door openers represent a blend of functionality, security, and user convenience. Homeowners seeking reliable, smart, and efficient solutions for managing their garage doors will find these models highly effective, offering peace of mind and ease of use in their everyday lives.
Top Page Image Contents