Craftsman 139.53335SRT3, 139.53834SRT3, 139.53646SRT2, 139.53648SRT2 L!Li, Hang the Opener

Page 17

Installation Step 5

Hang the Opener

Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener. The bracket and fastening hardware are not _rovided. See accessory page 38.

Measure the distance from each side of the opener to the structural support.

Cut both pieces of the hanging bracket to required lengths.

Drill 3/16" pilot holes in the structural supports.

Attach one end of each bracket to a support with 5/16"-18xl -7/8" lag screws.

Fasten the opener to the hanging brackets with 5/16"-18x7/8" screws, lock washers and nuts.

Check to make sure the T-rail is centered over the door (or in line with the header bracket if the bracket is not centered above the door).

Remove the 2x4. Operate the door manually. If the door hits the rail, raise the header bracket.

Grease the top and underside of the_ rail surface where the trolley __ slides. A tube of grease is /__ supplied.

Hardware Shown Actual Size

I!!l!l!;LI!

5/16'18xl-7/8"

Hex Screw

5/16'- 18x7/8"

Nut 5/16"-18

Lock Washer 5/16"

Figure 1

Supports

Screws

5/15/-18xl-7/8'

Measure

5/16'-18x7/8" Screw

_16" Lock Washer

5/16"-18 Nut

Figure

2

 

 

 

 

 

 

 

 

 

 

 

 

 

Hidden

 

 

 

/

"

_ t

 

 

 

 

 

Support

I

"

"

 

 

 

/

 

 

/.

/

"_

_

_._f

 

 

_

_

--

FINISHED

CEILING --

 

 

 

- _

 

 

 

Lag Screws

 

 

 

-

 

 

 

 

 

5/16 -18xl-7/5/_

_ "

 

Bracket

 

 

 

 

o

o

o

o

 

 

_ _-

.

 

 

 

.

 

."-_

 

 

 

 

___5/16"

Lock Washer.u,

5/16 18_

17

Image 17
Contents Craftsman Start by reviewing these important safety alert symbols YoullNeed Tools Closed Position Sectional Door InstallationOne-Piece Door With Track ONE-PIECE Door Installation One-PieceDoor Without TrackTO your Installation Carton Inventory Wit w edT oHardware Installation HardwareSafety Reversing Sensor Installation Assemble the T-rail & Attach Cable Pulley Bracket Assembly Section Pages 8Operation,noiseand/or RightWrong Hardware Shown Actual SizeHardware Shown Install the Trolley on the T-railActual Size Fasten Raft to OpenerMasterFigure Assembly StepInstall the Chain/Cable Attach the Sprocket Cover Tighten the Chain & Cable Trolley before adjusting chainIll AbovethedoorIF1 --L--Ji One-piece door without track Pivot hardware One-piece door without track Jamb hardwareFasten the Header Bracket to the Ceiling Install the Header BracketFasten the Header Bracket to the Wall Attach the T-rail to the Header Bracket Sectional Door & ONE-PIECE Door with Track Position the OpenerHang the Opener L!LIDo not connect to live electrical wiring. Connect Install the Door ControlDoor Control Button Fasten securely with 6ABx1-1/2 screws IllllllllltllllllllllllAttach the Emergency Release Rope and Handle Install the Light and the Lens32 explains how to use the door control RightWrong Permanent Wiring ConnectionsElectrical Requirements Facing the door from inside the garage Safety Reversing SystemRight sides of the door Finger tighten the lock nuts Install the Safety Reversing SensorShown Actual Size Alternate Wall MountTrouble Shooting Fasten Door Bracket IIIIIII!!11111!111II!!l!ll!!!lLllllllllllllllI!l!l!l SEC!ONA DoorS Oniy Connect Door Arm to TrolleyHole Alignment AlternativeOpen Door Adjustment Decrease UP limit Adjustment Procedures for One-PieceDoorsClosed Door Adjustment Decrease Down limit Assemble the Door ArmTo Adjust the Limits Adjustment Section Adjustment StepAdjust the UP and Down Limits Pages 28How and When to Adjust the ForceAdjust the Forces Test the Down close forceTest The Safety Reversing Sensor Adjustment StepTest the Safety Reverse System Must reverse on striking the obstructionTo reduce the risk of severe injury or death to persons MaintenanceCare of Your Opener ScheduleLockout position Operation of Your Opener53000SRT Series Garage Door Openers Receiver and Remote Control ProgrammingSituation Having a Problem?Probable Cause and Solution Probable Cause & Solution Having a Problem?Installation Parts Repair PartsWie \Fr Opener Assembly PartsAccessories Index For in-home major brand repair service For the repair or replacement parts you needGive the following information Product Type Part Number Model Number Part Description

139.53648SRT2, 139.53645SRT3, 139.53834SRT3, 139.53335SRT3, 139.53646SRT2 specifications

The Craftsman 139.53660SRT1, 139.53646SRT2, 139.53335SRT3, 139.53834SRT3, and 139.53645SRT3 are a series of advanced garage door openers designed for homeowners looking to enhance convenience, security, and functionality in their daily lives. Each model is equipped with cutting-edge technologies that streamline garage access while ensuring safety and durability.

One of the standout features across these models is the use of a powerful motor system, providing reliable performance for heavy garage doors. The motor's horsepower rating varies across the models, but all ensure consistent lifting strength and rapid opening and closing speeds, catering to different door weights and sizes.

In terms of security, these Craftsman models incorporate advanced encryption technologies, making unauthorized access nearly impossible. The security features include rolling code technology, which changes the access code each time the remote is used, thus preventing cloning and ensuring that only authorized users can operate the door.

These openers also prioritize ease of use. With their compatible smartphone app integration, users can remotely control and monitor their garage doors. Whether they are at home or away, users can receive notifications, check the status of their doors, and even open or close them at the touch of a button, adding an extra layer of convenience.

The installation process is also user-friendly, with many of these models featuring an easy-to-follow instruction manual. Homeowners can typically complete the installation themselves, saving time and money compared to hiring a professional. The durable construction of these openers ensures that they withstand the test of time, with many units equipped with weather-resistant materials that protect against rust and corrosion.

In addition to their functional features, the aesthetic designs of the Craftsman series are noteworthy. They fit seamlessly into a variety of garage styles, with a sleek finish that enhances overall garage appeal.

Overall, the Craftsman 139.53660SRT1, 139.53646SRT2, 139.53335SRT3, 139.53834SRT3, and 139.53645SRT3 garage door openers represent a blend of functionality, security, and user convenience. Homeowners seeking reliable, smart, and efficient solutions for managing their garage doors will find these models highly effective, offering peace of mind and ease of use in their everyday lives.