Craftsman Complete Guide on How to Install Garage Door Opener Keypad
Page 33

Receiver and Remote Control Programming

To comply with FCC rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code sening or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Models with 3-function remote controls: The

remote control(s) has been factory set to operate with the large push button. However, you can use either of the two small buttons, if you prefer. And, the 3-function remote control(s) can also activate additional garage door openers and/or light controls.

Below are instructions for programming your opener to match the other buttons on your remote controls and any additional remote controls you may )urchase. See available accessories on page 38.

53000SRT Series Garage Door Openers

(With "SRT" Button)

Your "SRT" garage door opener will operate with as many as four "SRT" portable remote controls and one Multi-Function Keyless Entry.

To Add A Remote Control

1.Press and ho/dthe selected remote push button, see Figure 1.

2.Then press and release the "SRT" (learn) button on the back panel of the opener, Figure 2. The opener light will flash once.

3.Release the remote push button.

Now the opener will operate when the remote control push button is pressed.

If you release the remote control push button before the opener light flashes, the opener will not accept the code.

To Change the Selected Push Button

On the Same Remote Control

If you decide to use a different remote control button than originally programmed into the opener, you need to erase allthe learned codes and reprogram each remote control used to operate the garage door opener.

To Erase All Remote Control Codes

•Press and hold the "SRT' button on the opener panel until the indicator light turns off (about 6 seconds). AIIthe codes the opener has learned will be erased.

•To reprogram, repeat Steps 1,2 and 3 for each remote control in use.

Code programming instructions are also located on the opener panel.

Children operating or playing with a garage

door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the door push button(s) or remote control(s).

A moving garage door could injure or kill someone under it. Activate the opener only

when you can see the door clearly, it is free of obstructions, and is properly adjusted.

Figure I

Select a remote control push

butlon to operate opener

3-Function Remote Control

Figure 2

Garage Door Opener

 

(With "SRT" Button)

'SRT" (learn)

Indicator

BACK

Button

Light

PANEL

To Add the Keyless Entry

We recommend that you program your code before you install the Keyless Entry. You will not need assistance, and you can test the reception at the mounting location before installation.

1.Choose a 4-digit code using numbers from 0 to 9. You can use a number more than once (for example, 4, 0, 4, 1). Press the selected code digits on the keypad.

2.Press and ho/dthe Enter button while you press the "SRT" (learn) button on the opener panel. The

indicator light will blink and the door will begin to move.

3.Release the Enter button. Now the opener has learned the selected keypad code.

To ensure that your portable remote control codes were not disturbed while you were programming the Keyless Entry, test your remotes and reprogram them if necessary.

To change the code at any time, repeat steps 1-3.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Craftsman Start by reviewing these important safety alert symbols YoullNeed Tools Closed Position Sectional Door InstallationONE-PIECE Door Installation One-PieceDoor Without Track TO your InstallationOne-Piece Door With Track Carton Inventory Wit w edT oInstallation Hardware Safety Reversing Sensor InstallationHardware Assemble the T-rail & Attach Cable Pulley Bracket Assembly Section Pages 8Operation,noiseand/or RightWrong Hardware Shown Actual SizeHardware Shown Install the Trolley on the T-railActual Size Fasten Raft to OpenerAssembly Step Install the Chain/Cable Attach the Sprocket CoverMasterFigure Tighten the Chain & Cable Trolley before adjusting chainAbovethedoor IF1 --L--JiIll One-piece door without track Pivot hardware One-piece door without track Jamb hardwareInstall the Header Bracket Fasten the Header Bracket to the WallFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Sectional Door & ONE-PIECE Door with Track Position the OpenerHang the Opener L!LIDo not connect to live electrical wiring. Connect Install the Door ControlDoor Control Button Fasten securely with 6ABx1-1/2 screws IllllllllltllllllllllllInstall the Light and the Lens 32 explains how to use the door controlAttach the Emergency Release Rope and Handle Permanent Wiring Connections Electrical RequirementsRightWrong Facing the door from inside the garage Safety Reversing SystemRight sides of the door Finger tighten the lock nuts Install the Safety Reversing SensorShown Actual Size Alternate Wall MountTrouble Shooting Fasten Door Bracket IIIIIII!!11111!111II!!l!ll!!!lLllllllllllllllI!l!l!l SEC!ONA DoorS Oniy Connect Door Arm to TrolleyHole Alignment AlternativeOpen Door Adjustment Decrease UP limit Adjustment Procedures for One-PieceDoorsClosed Door Adjustment Decrease Down limit Assemble the Door ArmTo Adjust the Limits Adjustment Section Adjustment StepAdjust the UP and Down Limits Pages 28How and When to Adjust the ForceAdjust the Forces Test the Down close forceTest The Safety Reversing Sensor Adjustment StepTest the Safety Reverse System Must reverse on striking the obstructionTo reduce the risk of severe injury or death to persons MaintenanceCare of Your Opener ScheduleLockout position Operation of Your Opener53000SRT Series Garage Door Openers Receiver and Remote Control ProgrammingHaving a Problem? Probable Cause and SolutionSituation Probable Cause & Solution Having a Problem?Installation Parts Repair PartsWie \Fr Opener Assembly PartsAccessories Index For in-home major brand repair service For the repair or replacement parts you needGive the following information Product Type Part Number Model Number Part Description

139.53648SRT2, 139.53645SRT3, 139.53834SRT3, 139.53335SRT3, 139.53646SRT2 specifications

The Craftsman 139.53660SRT1, 139.53646SRT2, 139.53335SRT3, 139.53834SRT3, and 139.53645SRT3 are a series of advanced garage door openers designed for homeowners looking to enhance convenience, security, and functionality in their daily lives. Each model is equipped with cutting-edge technologies that streamline garage access while ensuring safety and durability.

One of the standout features across these models is the use of a powerful motor system, providing reliable performance for heavy garage doors. The motor's horsepower rating varies across the models, but all ensure consistent lifting strength and rapid opening and closing speeds, catering to different door weights and sizes.

In terms of security, these Craftsman models incorporate advanced encryption technologies, making unauthorized access nearly impossible. The security features include rolling code technology, which changes the access code each time the remote is used, thus preventing cloning and ensuring that only authorized users can operate the door.

These openers also prioritize ease of use. With their compatible smartphone app integration, users can remotely control and monitor their garage doors. Whether they are at home or away, users can receive notifications, check the status of their doors, and even open or close them at the touch of a button, adding an extra layer of convenience.

The installation process is also user-friendly, with many of these models featuring an easy-to-follow instruction manual. Homeowners can typically complete the installation themselves, saving time and money compared to hiring a professional. The durable construction of these openers ensures that they withstand the test of time, with many units equipped with weather-resistant materials that protect against rust and corrosion.

In addition to their functional features, the aesthetic designs of the Craftsman series are noteworthy. They fit seamlessly into a variety of garage styles, with a sleek finish that enhances overall garage appeal.

Overall, the Craftsman 139.53660SRT1, 139.53646SRT2, 139.53335SRT3, 139.53834SRT3, and 139.53645SRT3 garage door openers represent a blend of functionality, security, and user convenience. Homeowners seeking reliable, smart, and efficient solutions for managing their garage doors will find these models highly effective, offering peace of mind and ease of use in their everyday lives.
Top Page Image Contents