Craftsman 39535006 Operation of Your Opener, Using the Opener, Opening the Door Manually

Page 21

Operation of Your Opener

CAUTION:

®START B Y READING THE SAFETY RULES ON PAGE 3.

e READ THE OPERATING INSTRUCTIONS ON THIS PAGE CAREFULLY° e DO NOT PERMIT CHILDREN TO PLAY IN AREA OF DOOR.

e OPERATE ONLY WHEN OPENER IS PROPERLYADJUSTEDAND DOOR IS IN SIGHTAND FREE OF OBSTRUCTION°

THE SAFETY REVERSE SYSTEM IS IMPORTANT (SEE PAGE 20). GARAGE DOOR MUSTREVERSE ON CON-

TACTWITH A ON E_iNCH OBSTACLE PLACED ON THE FLOOR. FAILURE TO PROPERLYADJUSTOPENER MAY

RESULT IN SERIOUS PERSONAL INJURY FROM A CLOSING GARAGE DOOR° REPEATTHE TEST AT LEAST ONCE A YEAR AND MAKE NEEDED ADJUSTMENTS°

USING THE OPENER

Your garage door opener can be activated by any of the following methods:

1o Pressing the transmitter push button. Hold the button down until door starts to move, 2. Pressing the Wall Control push buttons°

3.. By turning the Key Switch (if you have installed this accessory),,

WHEN EITHER THE WALL CONTROL OR TRANSMITTER PUSH BUTTONS ARE PRESSED, ONE OF THE FOLLOWING WILt. OCCUR (Vacation Light OFF):

1..If open, the door wilt close, if ctosed, the door will open.

2..if closing, the door will reverse.

3..If opening, the door will stop (allowing space for entry and exit of pets and for fresh air).. 4, tf the door has been stopped in a partially open position (refer to 3o above), it will close,. 5_ if an obstruction is encountered while closing, the door wilt reverse..

6. If an obstruction is encountered while opening, the door will stop..

7o The optional Infrared Reversing Sensor, if installed, will signal the opener to reverse the door in the closing cycle when the IR beam is obstructed and prevent an open door from closing. It has no effect in the opening cycle..

THE LIGHTS

When the opener is activated, lights will turn on_ They will turn off automatically after 4-1/2 minutes, BULB SIZE-75 watts maximum.. When Work Light is ON, the lights will remain on.

OPENING THE DOOR MANUALLY

The door can be operated manually by disconnecting it from the opener. Simply pull down sharply on the red

emergency release handle.. The door may now be lifted manually_ DO NOT USE EM ERGE NCY ROPE AND HANDLE TO PULL TH E DO0 R OPEN OR CLOSED. To automatically reconnect the door to the open er, press the Wall Control

push button

CARE OFTHEOPENER

When properly installed, your opener wilt perform efficiently with a minimum of maintenance. You will be required to replace a light bulb or change a transmitter battery from time to time° A 9-Volt AIkaline battery is the most reliable, and is available at Sears..

The opener does not require additional lubrication - HOWEVER - the door rollers, bearings and hinges should be oiled yearly.,

Most complaints of unsatisfactory opener operation can be traced to problems with the door itself. The opener is not intended to correct problems caused by an unbalanced or binding door, broken door springs or fautty door hardware. When operating the door manually, a properly balanced door will stay in any point of travel while being supported soley by its springs. If you encounter any difficulty when operating door manually, call a garage door serviceman.

RADIO CONTROLS

Refer to pages 22 and 23 for complete details°

LIMIT AND FORCE ADJUSTMENTS

Refer to pages 18 and 19 for limit and force adjustmentsThese adjustments must be checked and properlyset when opener is installed_Weather conditions may cause minor changes in door operation requiring some change in adjustments,

particularly during the first year of operation. Only a screwdriver is required. Follow instructions carefully_

CHAIN TENSION ADJUSTMENT

After installation of opener and adjustment of forces and limits, chain may appear loose,. This is normal. TO CHECK CHAIN TENSION: disconnect the trolley by pulling red emergency handle_ If chain returns to position described in Step 5, Page 9, DO NOT make further adjustments,

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 39535006 Youll Need Tools Tial Reinforcement to Avoid Door DAMAGE. see page 10o Illustratedbelow Opener Carton ContainsFrared Open Door IndicatorReversing SensorSTE P Assembmy=E P 2 Connect Trolley & Attach Chain Retainer Bracket AssembInstall Chain and Cable AssemblyGg P 5Tighten the Chain and Cable Ass÷mbUvInstall Door Bracket and Plate InstalaationBracket and Plate Example NstanUationNstamlation ProcedureSTE P 4 po,,io. Opener Chassis Attach Tee Rail to Header BracketHang Opener Chassis UnstaIlationTE P Attach Emergency Release Rope & HandleControl Operation Wall0nstatUation ConnectElectricPowerConnect Door Arm to Trolley InstalationProcedures Adjustment Procedure Open Door AdjustmentProcedure Closed Door Adjustment Nstam ationAdjust UP and Down Limits Test Door for BindingIf Opener Reverses Before Door Closes Fully Adjust Sectional Door Install tnfraredDown ONE-PIECE DoorOperation of Your Opener Using the OpenerOpening the Door Manually Care OftheopenerBattery Radio ControlsTransmitter Radio ControlJs Sears Td nanj Radio ControJ Matching Your Code in a NEW TransmitterChange the Code in Your Transmitters LI Dl Transmitter SchematicPage RAI L Assembly Parts List Repair PartsKEY Part Description Chassis Assembmy Parts ListFull 90 DAY Warranty on Garage Door Opener HOW to Order Repair PartsLimited Warranty Limited Warranty on Motor

39535006 specifications

The Craftsman 39535006 is a versatile and reliable tool designed for both professionals and DIY enthusiasts. This utility tool is part of Craftsman’s extensive range of power tools, known for their durability and innovation. The 39535006 is particularly recognized for its ergonomic design, which makes it comfortable to handle during extended use.

One of the main features of the Craftsman 39535006 is its powerful motor, delivering robust performance suitable for a variety of tasks. Whether you're working on heavy-duty projects or simple home repairs, this tool provides consistent power and efficiency. Its high-torque capabilities allow it to tackle demanding applications, while maintaining precision and control.

Another standout characteristic is the adjustable speed settings. The Craftsman 39535006 allows users to select the optimal speed for their specific project, enabling enhanced control and accuracy. This feature is especially beneficial when working with different materials, as it minimizes the risk of damage while maximizing effectiveness.

In terms of technology, the Craftsman 39535006 incorporates advanced safety features designed to protect the user. The built-in electronic brake is an excellent addition, stopping the tool quickly to minimize potential hazards. Additionally, the tool features an integrated LED light, which illuminates the workspace, providing clarity in low-light conditions.

The build quality of the Craftsman 39535006 is another hallmark of its design. Constructed with high-grade materials, the tool is not only robust but also resistant to wear and tear. This durability ensures that it can withstand the rigors of frequent use, making it an excellent investment for anyone looking to enhance their tool collection.

Furthermore, the Craftsman 39535006 is compatible with a wide array of accessories, allowing for customization based on individual project needs. This versatility means that users can adapt the tool for various tasks, from drilling to sanding, adding to its overall functionality.

In summary, the Craftsman 39535006 combines power, precision, and safety in a single, user-friendly package. With its ergonomic design, adjustable speed settings, and durable construction, this tool stands out in the market. Whether for professional use or home improvement projects, the Craftsman 39535006 is equipped to meet the needs of any user.
Top Page Image Contents