GB
A
C
E
1 | B |
3
2
46 87
For fan
Press the 3 [selecting operation] button and bring up the “FAN” display.
•The fan operation functions to circulate the air in the room.
•The temperature of the room cannot be set by fan operation.
Caution:
Never expose your body directly to cool air for a long time. Excessive expo- sure to cool air is bad for your health, and should therefore be avoided.
Dry operation
The dry is a
1.Until reaching room temperature of your choice
The compressor and indoor fan function is linked motion according to the change of the room temperature and automatically repeat ON/OFF.
2.When reaching room temperature of your choice Both the compressor and indoor fan stop.
When stop continues for 10 minutes, the compressor and indoor fan are oper- ated for 3 minutes to keep the humidity low.
For heating
Press the 3 [selecting operation] button to bring up the “HEAT” display.
Regarding displays during heating operation “DEFROST”
Displayed only during the defrosting operation.
“STAND BY”
Displayed from the start of heating operation until the moment warm air blows out.
Caution:
•When the air conditioner is used together with burners, thoroughly ven- tilate the area. Insufficient ventilation can result in accidents due to oxy- gen deficiency.
•Never place a burner at a place where it is exposed to the airflow from the air conditioner.
Doing so can result in imperfect combustion of the burner.
•The microcomputer functions in the following cases:
•Air does not blow out when heating starts.
-To prevent any cool air from escaping, the indoor fan is gradually switched in sequence from faint airflow/weak airflow/set airflow according to the tem- perature rise of the blown out air. Wait a moment until the airflow comes out naturally.
•The fan is not moving at the set speed.
-In some models, the system switches over to faint airflow when the tempera- ture of the room reaches the set temperature. In other cases, it stops to prevent any cool air from escaping during the defrosting operation.
•Air flows out even if operation is stopped.
-Approximately 1 minute after the stop of operation, the indoor fan sometimes rotates to eliminate extra heat generated by the electric heater, etc. The fan speed comes to low or high.
3.3. Room temperature adjustment
To change room temperature
Press the 1 [room temperature adjustment] button and set the room tem- perature of your choice.
Pressing 
or 
once changes the setting by 1 °C [2 °F].
If the pressing is continued, the setting continues to change by 1 °C [2 °F].
•Indoor temperature can be set within the following range.
Cooling/dry: 19 °C [67 °F] – 30 °C [87 °F]
Heating: | 17 °C [63 °F] – 28 °C [83 °F] |
•It is impossible to set the room temperature by the
*The range of room temperature display is 8 °C [46 °F] - 39 °C [102 °F]. Outside this range, the display flashes either 8 °C [46 °F] - 39 °C [102 °F] to inform you
if the room temperature is lower or higher than the displayed temperature.
3.4. Fan speed adjustment
To change fan speed
Every time you press the 6 [fan speed] button once, it switches from the low- speed to
In the electronics dry operation, the indoor fan automatically turns to
*Every time the fan speed adjustment button is once pressed, the fan speed is changed.
Fan speed : 2 stages
Display: | (Low)→ | (High) |
|
|
|
|
| ||
Fan speed : 4 stages |
|
|
| |
Display: | (Low)→ | (Mid2)→ | (Mid1)→ | (High) |
3.5. Adjustment of up/down airflow direction
To change the up/down airflow direction
PFFY-NEMU-A
While pulling the blowout grill out toward you, raise the rear, remove it, change the direction, and set it in place.
Caution:
Avoid putting your hand into the air outlet of the indoor unit any more than necessary during operation. If you get your hands caught in the metal parts when adjusting the
3.6. Time setting
•Set the current time after turning ON the power of the air conditioner or after restoration from a power failure.
•It can be set regardless of the operation of the indoor unit.
•During the time operation, the
1.Press the 4 [time selection] button and bring up the A “current time” display
•Every time it is pressed, the display changes.
| | “current | AUTO | | “timer start | AUTO | “timer end |
| |||
CLOCK | time” | | ON | time” | OFF | | time” | (no display) | |||
| | | |||||||||
|
| ||||||||||
|
|
|
|
|
|
|
| ||||
Caution:
When the current time is not yet set, the “CLOCK (current time)” display flashes, disabling the setting of timer operation.
2. Set the current time by pressing the 4 
or 
button
• The time cannot be set while the C “
” is displayed.
• While the A “CLOCK” time is displayed, press the time setting 4
/ buttons and set the time.
• The setting advances one minute every time the 4 
button is pressed once, and retrogresses one minute every time the 4
button is pressed once.
When respective 4 
/
buttons are pressed continuously, the time display goes fast forward. It advances in the order of 1 minute unit - 10 minute unit - one hour unit.
•About 10 seconds after the button operation has been completed, the C “cur- rent time” and A “CLOCK” displays disappear.
Caution:
•Remote controller is equipped with a simplified clock with a precision of about + or - one minute per month.
•The time must be readjusted (reset) every time the air conditioner is sub-
jected to a power stop of the air conditioner or a power failure.
6